Use and Care Manual

DRYLOK® WetLook High Gloss Sealer
DRYLOK® Wetlook Sealer is a clear, non-
yellowing, water-based acrylic coating
formulated for use on interior or exterior
masonry surfaces. Provides superior
hardness and durability. Protects against
efflorescence (white, powdery, salt-like
deposits) visible on the masonry. Built in
ash rust resistance prevents orange
staining of surface when applied to
masonry containing natural metals.
Excellent chemical resistance to de-icing
salts. Compatible with polymeric sand.
Our highest level of moisture vapor
barrier protection (25% solids)
Resists de-icing salts
Interior/exterior
Use on bare masonry or previously
painted surfaces
SaltLok® Technology helps prevent the
leaching of minerals and salt
Ideal for horizontal and vertical masonry
surfaces such as walkways, concrete
driveways, garage oors, basement oors,
concrete sidewalks, pavers, bare or
painted brick, poured concrete,
Chaahoochee stone, stamped concrete
and articial stone, terrazzo, and slate
surfaces.
DRYLOK® WetLook Sealer is not for use
on wood, metal, granite, marble, over
silicone treated surfaces, or on any
masonry surface subjected to hydrostatic
pressure. Vertical masonry surfaces
subjected to hydrostatic pressure should
be treated with DRYLOK® Masonry
Waterproofer.
COMPOSITION:
Latex base
SHEEN:
High gloss
% WEIGHT SOLIDS:
25% ± 0.5%
DENSITY (LBS./US GAL.):
8.5 ± 0.3 (1.02 g/L)
VISCOSITY:
12-18 Seconds #4 Ford Cup @ 77ºF
(25ºC)
pH:
8.5-9.5
COLORS:
Transparent
DRY TIME:
• To touch: 1 hour
• To recoat: 4 hours
• Light foot traffic: 24 hours
• Heavy foot traffic: 72-96 hours
• Clean with a mild, non-abrasive
liquid detergent: 30 days
• Rain free: 24 hours
Note: Maximum cure and dry time
will be prolonged when slightly
humid and damp, cool conditions
prevail.
CLEAN UP:
Soap and water
Dispose of contaminated absorbent,
container and unused contents in
accordance with local, state and
federal regulations.
COVERAGE (SQ. FT./GAL.):
• 200-400 sq. ./gal. (33 m
2
)
Note: Actual coverage will vary
depending upon application
method, surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT:
4 wet mils/coat (100 microns)
SHELF LIFE:
5 Years unopened container
FREEZE/THAW:
Keep from freezing.
CONTAINER SIZES:
One gallon (US) and ve gallon (US)
containers
Does not exceed 100 g/L
N/A
Remove all dirt, wax, dust, mildew, and
loose or scaling material with a scraper,
wire brush, or stiff bristle brush. Masonry
surface must be dry and free of dirt, wax,
dust, mildew, and loose or scaling material.
For proper penetration and adhesion to
extremely smooth bare concrete oors,
use DRYLOK® ETCH (liquid or powder)
or muriatic acid. Rinse thoroughly
(pressure wash for best results). Allow to
dry thoroughly according to
manufacturer’s directions.
If using a pressure washer, do not use on a
pressure seing above 1750 PSI to avoid
damaging the concrete. Remember,
concrete acts like a stone sponge. Pressure
washing and general cleaning may trap
residual moisture in the concrete.
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.ugl.com
D R Y L O K ® M A S O N R Y P R O D U C T S
O V E R
S
o
a
p
DRY TIME:
1 Hour
Recoat 4 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
1 Coat,
2 Maximum
SPREAD RATE:
200-400 Sq.
Ft./Gallon
32 13 16 DECORATIVE CONCRETE PAVING
09 97 23 CONCRETE AND MASONRY COATINGS
DIV. 09 & 32