Use and Care Manual
LR1219
DISCLAIMER:This information is furnished without
warranty, representation, inducement or license of any
kind, except that it is accurate to the best of UGL’s
knowledge, or obtained from sources believed by UGL to
be accurate, and UGL does not assume any legal
responsibility for use or reliance upon same. Before using
any product, read the label.
CAUSE SERIOUS ILLNESS, SUCH AS BRAIN
DAMAGE, ESPECIALLY IN CHILDREN.
P
REGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH-
approved respirator to control lead
exposure. Clean up carefully with a HEPA
v
acuum and a wet mop. Before you start,
nd out how to protect yourself and your
f
amily by contacting the National Lead
Information Hotline at 1-800-424-LEAD or
log on to www.epa.gov/lead.
For Active Leaks (the presence of owing
water through a break in the surface): Mix
and wait 1 minute or until the mixture
becomes warm to the touch which indicates it
is commencing to set. At this time force the
DRYLOK® Fast Plug® into the opening with
the palm of the hand. Hold in place for 3-5
minutes, assuring a complete set and
sufficient bond to stop the ow of water. e
patched area may be smoothed and
trimmed to the surrounding area in
approximately 5 minutes.
DRYLOK® Fast Plug® may be painted when
set with DRYLOK® Original Basement &
Masonry Waterproofer, DRYLOK®
Powdered Basement & Masonry
Waterproofer or DRYLOK® Concrete Floor
Paint.
For Inactive Leaks, Patching, Anchoring:
oroughly soak the area to be patched. is
will prevent the surface from sucking the
water out of the patching material. Apply
with knife or trowel, forcing the patch into the
affected area. Use the surface to smooth the
patch evenly. When anchoring, chisel or drill
hole in the masonry surface slightly larger
than item to be anchored. Make certain
mixed DRYLOK® Fast Plug® is tamped rmly
into hole and around metal part.
Cancer hazard: Contains Crystalline
Silica, which can cause cancer. (Risk of
cancer depends on duration and level of
exposure).
Use only with adequate ventilation. Do
not breathe dust. Harmful if inhaled.
O
verexposure may cause lung and kidney
damage. Avoid contact or prolonged
contact with eyes, skin, and clothing. Ensure
fresh air entry during application and
d
rying. If you experience eye watering,
headache, or dizziness, or if air monitoring
d
emonstrates vapor levels are above
applicable limits, wear an appropriate,
properly ed respirator (NIOSH
approved) during and aer application.
Follow respirator manufacturer's directions
for respirator use. Close container aer each
use. Wash thoroughly aer handling.
First Aid: If you experience difficulty in
breathing, leave the area to obtain fresh air.
If continued difficulty is experienced, call
poison control center, hospital emergency
room, or physician immediately. In case of
contact, immediately ush skin with soap
and plenty of water. In case of eye contact,
ush with plenty of water for at least 15
minutes. Consult a physician immediately.
KEEP OUT OF REACH OF CHILDREN
WARNING: Cancer and Reproductive
Harm - www.P65warnings.ca.gov.
For additional health and safety information
please refer to the “Safety Data Sheet”.
Compressive strength of cured material at:
1 Hour 311 PSI
3 Hours 365 PSI
8 Hours 396 PSI
24 Hours 2650 PSI
7 Days 3050 PSI
28 Days 11975 PSI
DRYLOK® and Fast Plug® are registered trademarks of United Gilsonite Laboratories (UGL).
Fast Plug® - Gray
1
1
⁄2 LB. 6/Case . . . . . . . . . . . . . . . .00919
4 LB. 4/Case . . . . . . . . . . . . . . .00917
10 LB. 2/Case . . . . . . . . . . . . . . .00924
50 Lb. 1/Case . . . . . . . . . . . . . . .00930