Use and Care Manual

DRYLOK® Fast Plug® is a quick seing
hydraulic cement. It sets in 3-5 minutes to
stop active leaks, even under pressure.
Seals open joints, very large cracks in
masonry walls and oor and wall joints.
Fast setting hydraulic cement
Sets in 3-5 minutes
Stops water, even under pressure
Patch mortar joints, cracks and holes in
masonry walls
No top-coat required
Reduces radon gas penetration
Anchors metal to concrete. Ideal for
sealing oor and wall joints and selement
cracks in masonry walls and swimming
pools. is fast-seing hydraulic cement
patches holes even where water is actively
owing through them.
Mix only enough for immediate use,
because DRYLOK® Fast Plug® sets in 3-5
minutes. Cannot be reworked once it has
set.
COMPOSITION:
Sand and cement
% WEIGHT SOLIDS:
100%
DENSITY (LBS./US GAL.):
24.0 ± 0.3% (S.G. 2.87 ± 0.02)
COLORS:
• Gray – ready mixed formula
SET TIME:
• 3-5 minutes
Note: Maximum cure and dry time
will be prolonged when slightly
humid and when damp, cool
conditions prevail.
CLEAN UP:
Soap and water
Dispose of contaminated absorbent,
container, and unused contents in
accordance with local, state, and
federal regulations.
COVERAGE:
16 cu. in./lb. 578 cu cm
2
/kg
Note: Actual coverage will vary
depending upon application
method, surface texture, and
porosity.
SHELF LIFE:
Unlimited in tightly closed container
FREEZE/THAW:
N/A
CONTAINER SIZES:
One and a half pound (US), four
pound (US), ten pound (US) and y
pound (US) containers
N/A
N/A
Wear eye protection, rubber gloves, and a
dust mask. e area to be patched should
be cleaned thoroughly by wire brushing,
scraping, or any other effective process.
Back chisel out the area to be patched to
the shape of an inverted “V” (the point at
the surface) until loose, crumbling
masonry is removed and a sound surface
remains. is allows the patch to expand
and lock into the surface. Wet down the
area prior to patching to help the
DRYLOK® Fast Plug® cure properly.
DRYLOK® Fast Plug® and clean mixing
water should be at room temperature
prior to mixing. Mix 3 parts DRYLOK® Fast
Plug® and 1 part water thoroughly to a
puy or heavy troweling consistency. is
mixture will set in 3-5 minutes. e use of
colder water will retard the seing time.
Mix only enough for immediate use due
to the quick seing time. In cold weather,
use warm (90°F, 32°C) water for mixing;
also soak surface with warm water before
application.
Mix only enough for immediate use,
because DRYLOK® Fast Plug® sets in 3-5
minutes. Cannot be reworked once it has
set.
Mix in small batches only. Mix only
enough for use in 3 minutes. Discard all
le over mixed patching material prior to
starting a new batch. Le over patching
material will chemically react with new
material in the mixing receptacle.
If you scrape, sand, or remove old paint,
you may release lead dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN
DRYLOK® FAST PLUG® Hydraulic Cement
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.UGL.com
D R Y L O K ® M A S O N R Y P R O D U C T S
O V E R
S
o
a
p
SET TIME:
3-5 Minutes
CLEAN-UP:
Soap and Water
COVERAGE:
1 Application
SPREAD RATE:
16 Cu. In./Pound
578 cm
2
/kg
03 15 13 WATERSTOPS | 03 01 00 MAINTENANCE OF CONCRETE
DIV. 03
correct
incorrect