User Manual

(6)
(3)
5. Hold the stack in position with the left hand and with the right hand, lower the clamp by turning the clamp wheel clockwise.
Proper clamping pressure is achieved when the clamp wheel is tightened 1/4 to 1/2 turn past where the clamp first makes
firm contact with the paper stack. Adding more pressure to the clamp may cause damage to the clamp, clamp mount plate,
and the roller bearing mechanism. Damage caused by over clamping is not covered under the 1-year limited warranty.
Excessive clamp pressure may cause the stock to be creased. The use of waste sheets above and below the stock to be
cut is a common protection method used to keep the finished stock from being marked or creased. If additional clamp-
ing pressure is required the blade may need to be sharpened. Continuing to cut with a dull blade may cause severe dam-
age to the cutting mechanism or handle. Damage caused by cutting with a dull blade is not covered by the 1-year
limited warranty.
See section 4.4.2 for proper blade removal
and 4.2 for sharpening instructions or call
Martin Yale Customer Service @ 260-563-
0641 for assistance.
6. Firmly grasp the blade handle grip and release
the spring-loaded safety arm. Lower the
blade handle with an even stroke to complete
the cut action (See Figure #2). The blade
should cut cleanly through the last sheet but
not too deeply into the cutting stick. If it does
not, the cutting stick may need to be rotated to
a fresh side (See 4.4.1). This condition may
occur if the blade is not level with the cutting
stick (See 4.3.2).
7. Return the blade handle to the fullest upward position. Make sure the
blade handle is securely locked in place by the safety latch.
8. Raise the paper clamp with counter clockwise rotation of the clamp
wheel.
9. Remove all cut material from the 7000E.

Please refer to the diagram and parts list in the back of this instruction booklet to assist you in identifying the parts.
5"2)#!4)/.
Whenever the blade is removed for sharpening, (see section 4.4.2) lubricate the clamp screw, the sides and slots of the
clamp mounting plate, and the lower portion of the handle assembly (where it pivots between the frame). Use a lithium
or petroleum base grease.
,!$%(!20%.).'
Dulling of the blade is a natural occurrence and is determined primarily by the type of material being cut. Many paper
products today are made of re-cycled materials and can be very abrasive to the blade. If it becomes increasingly more
difficult to cut paper, the cut is rough, or if excessive clamp pressure is required to hold the stack, then it is time to
sharpen the blade (see section 4.4.2). Always keep a spare blade on hand to use while you send out the dull one to be
sharpened by a qualified blade sharpener or machine shop. Blade is to be ground to a 19° angle for resharpening.
$*534-%.43
4.3.1 Squaring The Side Rail
To square the side rail, use a square of known accuracy and follow this procedure.
1. Lower the cutting blade until it rests on the cutting stick.
2. Loosen the three screws on the right side of the side rail.
The blade is sharp. Use extreme caution when working with or near the blade.
3. Place the short side of the square against the bottom of the blade and slide the square toward the side rail.
Figure #2
5.0 Parts List
Item. # Part # Qty. Description
1 WRA007053 1 Blade Handle Assy.
1A M-S043012 1 Handle Grip
2 M-S043046 1 Vinyl Safety Tip
3 M-O007055 1 Safety Latch Spring
3A M-S001157 1 10-32 x 5/8 Screw
4 W-A007050 1 Safety Plate Assy.
5 M-S002052 1 Blade Adjust Screw
5A M-S007019 1 5/16 - 18 Hex Nut
6 M-O007011 1 Short Spacer
7 WRA007007 1 Blade Assy.
8 W-O007022 1 Safety Plate
8A M-S003039 2 Safety Plate Screw
9 M-O007025 1 Small Wood Top
10 W-O007001 1 Front Frame
11 W-O007056 2 Spacer Extrusions
12
W-O007012
2 Blade Roller Guide
13 W-O007027 2 Stick Retainer
14 M-O007034 1 Cutting Stick
tem. # Part # Qty. Description
15
W-0007010
1 Long Spacer
16 M-O007039 1 Upper Frame Spacer
17 M-S030003 4 Frame Feet
18 W-A007005 1 Clamp Mount Plate
19 WRA007006 1 Clamp Assy.
20 W-A007015 1 Top Cover
21 M-O007013 1 Clamp Adjust Screw
21A M-S010033 1 Retaining Ring
21B M-S008041 1 Oilite Bushing
22 M-S042004 1 Hand Wheel
23 M-S043011 4 Tube Cap
24 M-O007024 1 Large Wood Top
25 W-O007042 1 Back Gauge
26 W-O007028 1 Paper Side Rail
27 M-S032041 1 Locking Knob
27A M-O007083 1 Plastic Screw Cap
NOT SHOWN
M-O007080 1 Blade Hook
M-O007016 1 Blade Assy. Roller
M-S63751051 4 1/4-20X1/2 Screws
M-O007030 1 Clamp Rubber Strip
M-S001129 1 Top Cover Screw
MRS042005 1 Spinning Knob/Clip
M-O007032 1 13” Lexan Ruler