User Manual

/$%,/--%2#)!,544%2
.34!,,!4)/.!).4%.!.#%0%2!4).'.3425#4)/.3
/$%,0%#)&)#!4)/.3
Thickness Capacity (24# bond) . . . . . . . . .1 1/2"
Width Capacity (With Stop) . . . . . . . . . . . . . .12"
Length Capacity . . . . . . . . . . . . . . . . . . . . . . .12"
Cutting Method . . . . . . . . . . . . . . . . . . . . . .Lever
Clamping Method . . . . . . . . .Manual Handwheel
Dimensions . . . . . . . . . . . . . . .19" x 19" x 13 1/8"
Shipping Weight . . . . . . . . . . . . .48 lbs. (21.8 kg)
!",%/&/.4%.43
1.0 Parts . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
2.0 Installation . . . . . . . . . . . . . . . . . . . . . Page 2
3.0 Operation. . . . . . . . . . . . . . . . . . . . . . Page 2
4.0 Maintenance . . . . . . . . . . . . . . . . . . . Page 3
5.0 Parts List . . . . . . . . . . . . . . . . . . . . . . Page 6
6.0 Parts Diagram . . . . . . . . . . . . . . . . . . Page 7
7.0 Troubleshooting. . . . . . . . . . . . . . . . . Page 8
Serial # ____________________

Thank you for selecting the Martin Yale Model 7000E Commercial Cutter. The 7000E has been performance-tested at the
Martin Yale factory. With recommended maintenance, the unit will provide years of trouble-free service. Please review this
publication in its entirety before attempting to operate your 7000E. Thorough understanding of this information will help
eliminate most operator-associated errors and ensure years of trouble-free performance.
 (%#544).'",!$%/&4(%)3%842%-%,93(!20%6%20,!#%(!.$3/2&).'%235.$%24(%
#544).'",!$%/2).4/4(%#544).'!2%!%2)/53"/$),9).*529#/5,$2%35,4%6%2!,,/7#(),$2%.4//0%2!4%
4(%5.350%26)3%$(%7%)'(4/&4(%(!.$,%#!.#!53%4(%#544).'",!$%4/$2/0)&4(%302).',/!$%$
3!&%49!2-)3./4&5,,9%.'!'%$,7!93-!+%352%4(%302).',/!$%$3!&%49!2-)3&5,,9%.'!'%$50/.4(%
#/-0,%4)/./&%!#(#54"92%452.).'4(%(!.$,%4/4(%&5,,502)'(40/3)4)/.%34&/23!&%49!2-%.'!'%-%.4
"%&/2%2%,%!3).'4(%(!.$,%
251 Wedcor Avenue • Wabash, IN 46992
Phone [phone] • Fax [phone]
website: www.martinyale.com • email: [e-mail]
M-S027057
Rev. 5
7/15/19

!0%2/4/-0,%4%,954
Gradual wearing of the cutting stick is normal during machine operation. As a groove is formed in the stick by the cut-
ting action of the blade, the blade may not completely cut through the bottom sheets of the stack. When this condition
occurs, rotate the cutting stick, or replace, if necessary. Also make sure the blade is level and is set for proper cutting
depth. See Section 4.3.2 and Section 4.4.1.
8#%33)6%2%3352%%#%33!29//-0,%4%54
Sharpen or replace the cutting blade according to instructions in Section 4.4.2.
NOTE: As an average, the cutting blade should be sharpened or replaced after eight cutting hours of 24# bond paper
(90g/m2). Cutting heavier or more abrasive material may necessitate more frequent sharpening or replacement of the
blade.
54!0%2354&15!2%
Make sure the paper stack is correctly aligned to the side rail and back gauge. Also make sure the paper stack is cor-
rectly clamped with the paper clamp. See Section 4.3.1.
(%,!-0 (%%,3!2$/52.
Lubricate the wheel according to instructions in Section 4.1.
(%!.$,%3!2$//6%02/7.
Lubricate the handle according to instructions in Section 4.1.
(%,!$%543..%)$%54/4(%4(%2
Level the blade according to instructions in Section 4.3.2.
(%,!$%543.(%%.4%2.,9
The cutting stick is bad. Follow instructions in Section 4.4.1.