Owner manual

ManualsBrandsDrucker Diagnostics ManualsOpticsModel 653ES Centrifuge

Operator’s Manual

Model 653ES • Laboratory Centrifuge

Rev. B

Replacement Parts:

Part No. Description

7724177 Rubber Foot

7751068 Switch, lid safety

7735049 Motor, 1/30 H.P., 115 V.A.C. permanent split capacitor

7729009 Capacitor, 5uF, 250V A.C.

7717046 Electronic timing and locking board, w/display

7751043 Circuit Breaker

7760002 Power cord

7714101 Pawl, latch, lid

7714103 Knob, latch, lid

7712316 Lid

7724071 Hinge, friction

7732018 Seal, lid gasket

7713030 2-Place 100mm Tube Carrier

7786048 Horizontal Rotor

Available Accessories:

1” Tube cushion

p/n 1525

Made in the USA by

0.25” Tube cushion

p/n 9150

P/N 7711014

WARRANTY:

The Drucker Company warranties that this centrifuge is free

from defects in workmanship and parts for 2 years.

200 Shadylane Drive • Philipsburg, PA 16866

Phone: 814-342-6205 or 814-692-7661 • Fax: 814-692-7662 • www.druckercompany.com

Summary of content (6 pages)

PAGE 1
P/N 7711014 Replacement Parts: Part No. 7724177 7751068 7735049 7729009 7717046 7751043 7760002 7714101 7714103 7712316 7724071 7732018 7713030 7786048 Description Rubber Foot Switch, lid safety Motor, 1/30 H.P., 115 V.A.C. permanent split capacitor Capacitor, 5uF, 250V A.C.
PAGE 2
Table of Contents Model Description Supplied Equipment Features Specifications Setup Location and Procedure Front Panel Controls Operation Rotor Removal and Installation Programming Functions Tube Holder Configurations Care and Maintenance Troubleshooting Safety, Emergency Lid Removal Calibration and Ground Testing Replacement Parts Available Accessories pg. 2 pg. 2 pg. 3 pg. 3 pg. 4 pg. 5 pg. 6 pg. 7 pg. 7 pg. 7,8 pg. 9 pg. 10 pg. 11 pg. 11 pg. 12 pg.
PAGE 3
NOTE: The latch must be turned completely clockwise to its stop position in order for the centrifuge to operate. Troubleshooting: 1. 2. 3. 4. 5. Problem: The rotor does not spin freely. Solutions: – Make sure nothing has fallen into the rotor chamber. – If there is nothing obstructing the rotor, contact The Drucker Company for further assistance. Problem: Excessive noise when the machine is running. Solutions: – Check to see that the load is balanced.
PAGE 4
Setup Location: 1. Unpack the centrifuge and verify that all of the supplied equipment is present. 2. Choose a setup location which meets the following criteria: a) A bench top clearance height of 20” is required in order to open the lid. b) The clearance envelope is the space around the centrifuge which is required for safety. Choose a setup location which will allow for a clearance envelope of at least 27” x 27”, (with the centrifuge at the center).
PAGE 5
Tube Carrier Configurations: The horizontal rotor shipped with your Horizon Centrifuge is capable of spinning tubes up to 16mm x 100mm. Use the following illustration to determine if you should use a tube cushion. Configuration A (100 mm tubes): Use the tube holder as is with no additional tube cushions. Configuration B (75mm tubes): Place a 1” tube cushion in the bottom of each of the tube locations in the tube holder as shown in the picture to the right. (Continued) 11.
PAGE 6
Operation: NOTE: Follow the initial setup procedure on page 4 before initial operation. 1. If the centrifuge is not plugged in, plug it into an approved 115 Volt A.C., 60 Hz. outlet. The centrifuge performs a warm-up process at power-up that takes approximately 50 seconds. 2. Push the ‘OPEN / EMERGENCY STOP’ button and then open the lid. 3. Insert cushions (if needed) into the tube carriers for the tube size you are using. Refer to ‘Tube Carrier Configurations’ (page 8) for assistance. 4.