User manual

ManualsBrandsDRS ManualsHome building and DecorWatchMaster IP Elite 3000

WatchMaster

IP Elite & Elite 3000 Quick Start Guide January 2013

Document Number 1012610 Version B

written consent of the copyright owner.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Install in accordance with the manufacturer’s instructions.

6. Do not defeat the purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong is provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

7. Use only with the tripod or bracket specified by the manufacturer, or

sold with the apparatus.

8. Installation of the equipment must comply with local and national

electrical codes.

9. This product must be connected to a Power Over Ethernet IEEE

802.af compliant power source or a UL Listed “Class 2” power supply

rated 12-24 V DC or 24 V AC minimum 13 W or 0.54 A.

10. Operating the camera at voltage levels outside the specified range

may result in permanent damage to the unit and void the product

warranty.

11. Clean the camera lens only with Kodak lens cleaning paper.

12. Failure to follow the proper procedure may cause permanent

damage to the camera and void the product warranty.

WARNING

DEVICE SENSITIVE TO ELECTROSTATIC DISCHARGE

The camera electronics and electronic interfaces are sensitive to

electrostatic discharge. Please follow appropriate ESD procedures when

handling the camera and during installation. For PoE installations, DRS

strongly recommends the use of STP cabling and an earth grounded end

point to ensure proper ESD immunity. For AC or DC powered

installations, a properly earth grounded power source is strongly

recommended.

CAUTION

To ensure a proper earth ground (between the DRS camera and a PoE

switch) DRS strongly recommends the use of Shielded Twisted Pair (STP)

cabling. Installations of DRS cameras using a STP cabling and a properly

earth grounded PoE switch are tested to comply with industry immunity

standards for Electro Static Discharge. Any other installation method may

leave the camera at risk and void the warranty.

Summary of content (11 pages)

PAGE 1
WatchMaster® IP Elite & Elite 3000 Quick Start Guide January 2013 Document Number 1012610 Version B Important Safety Instructions 1. 2. 3. 4. 5. 6. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Install in accordance with the manufacturer’s instructions. Do not defeat the purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
PAGE 2
WatchMaster® IP Elite & Elite 3000 Quick Start Guide Important Legal and Regulatory Information Introducing WatchMaster® IP Elite Legal Consideration ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE ARE PROVIDED “AS IS” WITH ALL FAULTS.
PAGE 3
WatchMaster® IP Elite & Elite 3000 Quick Start Guide   Installing the IP Elite Camera Quick Start Guide (this guide) End User Licensing Agreement (EULA) You will need the following items (not included) before you can install the IP Camera (recommended tool list)  Power source: PoE Switch, 12-24V DC or 24V AC  IP Network  Ethernet Cable (STP Cat5 recommended)  Tripod or Mounting bracket for mounting the IP Camera  A Phillips head #2 screwdriver  2 Open End Wrenches – 1 inch (25mm), OR adjustable w
PAGE 4
WatchMaster® IP Elite & Elite 3000 Quick Start Guide Preparing the Cable 1. Disconnect power from any previously installed cable(s). 2. Take the number 2 Phillips head screwdriver and pierce a hole in the center of the cable gland. 3. If needed, pierce the smaller holes on the outer perimeter of the cable gland membrane for AC/DC power and RS-485 (IP Elite 3000 only) wires 4. Remove the electric nut from the sealing gland. 5. Place the O-ring (Orange) on the threaded end of the cable gland.
PAGE 5
WatchMaster® IP Elite & Elite 3000 Quick Start Guide 3. 4. Attach one open end wrench onto the flange of the cable gland and tighten the compression nut, with the second open wrench, to approximately 8 in-lbs. of torque Assemble a new RJ45 head to the Cat 5 Ethernet Cable 5. 6. Assemble a new RJ45 head to the Cat 5 Ethernet Cable Assemble a mating power connector to the 2 AC or 2 DC power cables. IP66 (PoE only) Securing for IP66 (Ethernet & AC/DC Power): 1.
PAGE 6
WatchMaster® IP Elite & Elite 3000 Quick Start Guide 3. 4. 5. 6. Measure approximately 4.5 inches of cable slack from the end of the cable to the rubber grommet of the sealing gland. Use a scale to measure the length Attach one open end wrench onto the flange of the cable gland and tighten the compression nut, with the second open wrench, to approximately 8 in-lbs.
PAGE 7
WatchMaster® IP Elite & Elite 3000 Quick Start Guide d. 12. 13. 14. 15. 16. 17. RS-485: Connect wires to power block according to the previous pin-outs (IP Elite 3000 only) Reconnect Power to the existing cable(s) Check for Solid LED on the Ethernet connector to acknowledge connectivity to the IP network. The status LED indicators are: e. LED 1: Solid Green for 10MB connection or Flashing Green for Activity f. LED 2: Solid Amber for 100MB connection.
PAGE 8
WatchMaster® IP Elite & Elite 3000 Quick Start Guide Back Cover and White Desiccant Solar Shroud and Stem Bumpers Back Cover screws and Sealing Washer Fully assembled Camera 8
PAGE 9
WatchMaster® IP Elite & Elite 3000 Quick Start Guide Mounting the IP Elite Camera The IP Elite camera can be mounted on a Tripod or Pelco or Axis Bracket. For Tripod mount, use IP Elite Tripod Adapter offered as an accessory. For Pelco Mount, secure the Camera Base Mount to the Standard Pelco Bracket (not provided) using #6-32 X 5/8” screws (not provided). For Axis Mount, secure the Standard 4-Hole Axis Adapter provided to mount to the Axis Bracket (not provided) using the Metric M5 screws (not provided).
PAGE 10
WatchMaster® IP Elite & Elite 3000 Quick Start Guide Accessing the IP Elite Camera Login to the IP Elite Camera For Windows 7 OS, double click on the name of the Camera from the Device Discovery interface. For other Operating Systems, login to the router, find the attached IP Elite Camera and find its IP address. Enter the IP address of the IP Camera on the Browser URL line. A login screen will appear. Enter the default username and password.
PAGE 11
WatchMaster® IP Elite & Elite 3000 Quick Start Guide For More Information Congratulations!! DRS WatchMaster® IP Elite Camera Installation and Configuration is now complete. 11 Category DRS WatchMaster IP Elite Documentation Online Location http://www.drsinfrared.com DRS WatchMaster IP Elite Support http://www.drsinfrared.com VLC Media Player http://www.videolan.