Installation and Operation Manual Eco-65 (DP00060 model) Safety tested according to ULC S627, UL1482 and ASTM E1509 by an accredited laboratory INSTALLATION BY A PROFESSIONAL IS STRONGLY RECOMMENDED Fabricant de poêles international inc. 250, rue de Copenhague, St-Augustin-deDesmaures (Québec) Canada G3A 2H3 After-sale service: 418-908-8002 E-mail: tech@sbi-international.com www.drolet.ca CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA.
Eco-65 Installation and Operation Manual THANK YOU FOR CHOOSING THIS DROLET PELLET STOVE As one of North America’s largest and most respected pellet stove, wood stove and fireplace manufacturers, Stove Builder International takes pride in the quality and performance of all its products. We want to help you get maximum satisfaction as you use this product.
Eco-65 Installation and Operation Manual Table of contents 1 Introduction .............................................................................................................................................. 5 1.1 About Pellet Heating .............................................................................................................................. 5 1.1.1 Top 10 Reasons for Buying a Pellet Stove ...................................................................................
Eco-65 Installation and Operation Manual 7 Maintenance ........................................................................................................................................... 34 7.1 Stove Maintenance .............................................................................................................................. 34 7.1.1 Recommended Maintenance Schedule ..................................................................................... 34 7.1.
Eco-65 Installation and Operation Manual 1 Introduction 1.1 About Pellet Heating Pellet stoves offer a dramatic improvement in the convenience of heating with solid fuel. Wood pellets are handled in bags and are therefore easily and cleanly stored. A single loading of a pellet stove can provide long hours of warmth. Pellet stoves also provide a special comfort associated with wood burning.
Eco-65 Installation and Operation Manual 1.2 Appliance performance(1) Fuel type Wood Pellet (Premium grade or better)(☨) Recommended heating area[*] 800 to 2,600 ft2 (74 to 242 m2) Hopper capacity 125 lb (57 kg) Maximum burn time [*] 104 h Maximum heat input rate(2) 65,400 BTU/h (19.1 kW) Overall heat output rate (min. to max.)(3) 8,300 BTU/h to 36,700 BTU/h (2.4 kW to 10.8 kW) Average overall efficiency(3) 68.8% (HHV(4)) 74.4% (LHV(5)) Optimum efficiency(6) 79.9% Burn rate 1.
Eco-65 Installation and Operation Manual 1.3 General Features Recommended chimney diameter 4 po (see Section 4.
Eco-65 Installation and Operation Manual 1.
Eco-65 Installation and Operation Manual PART A – INSTALLATION 2 Installation Safety Information 2.1 Installation Warnings, Cautions and Recommendations PROFESSIONNAL INSTALLATION IS HIGHLY RECOMMENDED. YOU MAY NEED TO OBTAIN A BUILDING PERMIT FOR THE INSTALLATION OF THIS STOVE AND ITS VENTING SYSTEM. CONSULT YOUR MUNICIPAL BUILDING DEPARTMENT OR FIRE DEPARTMENT BEFORE INSTALLATION TO DETERMINE THE NEED TO OBTAIN ONE.
Eco-65 Installation and Operation Manual MIXING OF APPLIANCE COMPONENTS FROM DIFFERENT COMPONENTS IS PROHIBITED AND WILL VOID THE WARRANTY. ANY MODIFICATION OF THE STOVE THAT HAS NOT BEEN APPROVED IN WRITING BY THE TESTING AUTHORITY IS PROHIBITED AND VIOLATES CSA B365 (CANADA), AND ANSI NFPA 211 (USA). STOVE BUILDER INTERNATIONAL INC.
Eco-65 Installation and Operation Manual A POWER CORD OWNER’S B MANUAL C TOP GRILL D SCRAPER DESICCANT E (drying agent) SWEEPING F BRUSH (the tie wrap must be cut) 3 Clearances to Combustible Material The clearances shown in this section have been determined by tests according to procedures set out in safety standards ULC S627 (Canada), ASTM E1509 (U.S.A).
Eco-65 Installation and Operation Manual 3.1 Certification Label Location Since the information given on the certification label affixed to the stove always overrides the information published in any other media (owner’s manual, catalogues, flyers, magazines and/or web sites), it is important to refer to it in order to have a safe and compliant installation. In addition, you will find important information about your stove (model, serial number, etc.).
Eco-65 Installation and Operation Manual 3.3 Floor Protection For floor protection clearances refer to the following table.
Eco-65 Installation and Operation Manual 4 Venting system 4.1 General Even though the chimney draft is mechanical, a suitable venting system will ensure a natural draft which will prevent smoke spillage in your home if a power outage occurs. Moreover, a suitable venting system configuration will help getting the best efficiency out of your stove when installed in accordance with the required EVL (see Section 4.3: Equivalent Vent Length (EVL)).
Eco-65 Installation and Operation Manual Here is an example to help you calculate Equivalent Vent Length. On the following figure the EVL can be calculated like this: 2 horizontal run of 1’ = (2 X 1’) X 1’ = 2’ of EVL 1 elbow 90° or "Tee" = 5’ of EVL 3 vertical length of 4’ = (3 X 4’) X 0.5’ = 6’ of EVL Total EVL = (2’ + 5’ + 6’) = 13’ NOTE: Do not include the exterior wall termination in the EVL calculation (45° elbow and termination).
Eco-65 Installation and Operation Manual 4.4 Termination Location Termination should not be located so that hot exhaust gases can be a hazard. They can reach temperatures of 500°F (260°C) and cause serious burns. CAUTION: TERMINATION COLLAR (SPARK ARRESTER) IS MANDATORY. 4.4.1 Permitted Termination Location Refer to NFPA 211 (USA) or CSA B365 (Canada) for rules for the distance of exit terminal from windows and openings.
Eco-65 Installation and Operation Manual Canada: Letter Min.
Eco-65 Installation and Operation Manual USE RTV SILICONE (Room Temperature Vulcanization), METALLIC TAPE, AND A MINIMUM OF THREE SELF-TAPING SCREWS AT ALL JOINT CONNECTIONS TO ENSURE A TIGHT SEAL. THE CHIMNEY CONNECTOR SHALL NOT PASS THROUGH AN ATTIC OR ROOF SPACE, CLOSET OR SIMILAR CONCEALED SPACE OR FLOORS OR CEILING. INSTALL VENTING SYSTEM AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER. THE USE OF A SPARK ARRESTER AT THE END OF THE TERMINATION IS MANDATORY. 4.5.
Eco-65 Installation and Operation Manual 4.5.3 Through Roof Installation 1. Position stove following clearances given in Section 3.2: Minimum Clearances to Combustibles and following vent manufacturer’s instructions. 2. Install a cleanout tee to the stove flue outlet. If necessary, use a horizontal additional length between the flue outlet and the tee.
Eco-65 Installation and Operation Manual 4.5.4 Through a Factory Built Chimney To make an installation through a factory built chimney, run a 4" stainless steel liner inside the factory built chimney. 1. Position stove following clearances given in Section 3.2: Minimum Clearances to Combustibles and following vent manufacturer’s instructions. 2. Install a cleanout tee to the stove flue outlet. If necessary, use a horizontal additional length between the flue outlet and the tee.
Eco-65 Installation and Operation Manual 4.5.5 Through an Existing Masonry Fireplace 1. Position stove, following clearances shown in Section 3.2: Minimum Clearances to Combustibles and following vent manufacturer’s instructions. 12”-18” 2. Build and Install a blocking plate inside the chimney to seal the fireplace damper. Stainless steel plate and screws are recommended. Cut a hole for the exhaust pipe. If needed, cut a second hole for the air intake pipe (see Appendix D: Combustion Air Supply). 3.
Eco-65 Installation and Operation Manual 4.5.6 Through an Existing Masonry Chimney 1. Position stove following clearances shown in Section 3.2: Minimum Clearances to Combustibles and following vent manufacturer’s instructions. 12”-18” 2. Mark the center of the hole where the vent pipe will go through the masonry chimney. 3. It is necessary to make a hole in the masonry with a one-inch diameter greater than the diameter of the vent pipe used. 4. Install a vented flashing at the top of the masonry chimney.
Eco-65 Installation and Operation Manual PART B - OPERATION 4.6 General Information 4.7 Operation Warnings, Cautions and Recommendations KEEP THIS MANUAL FOR REFERENCE. DURING THE FIRST FEW FIRES, YOUR STOVE WILL EMIT AN ODOR AND A SMALL AMOUNT OF FUMES AS THE HIGH TEMPERATURE PAINT CURES OR BECOMES SEASONED TO THE METAL. MAINTAINING SMALLER FIRES WILL MINIMIZE THIS. AVOID PLACING ITEMS ON STOVETOP DURING THIS PERIOD TO AVOID DAMAGING THE PAINT SURFACE. MAKE SURE THE ROOM IS WELL-VENTILATED.
Eco-65 Installation and Operation Manual TURNING THE STOVE OFF DOES NOT DISCONNECT ALL POWER FROM THE STOVE. DISCONNECT THE POWER CORD BEFORE PERFORMING ANY MAINTENANCE OR REPAIRS ON THE STOVE. ALLOW THE STOVE TO COOL BEFORE CARRYING OUT ANY MAINTENANCE OR CLEANING. ASHES SHOULD BE PLACED IN A METAL CONTAINER WITH A TIGHT FITTING LID. THE CLOSED METAL CONTAINER SHOULD BE PLACED ON A NONCOMBUSTIBLE FLOOR OR ON THE GROUND, WELL AWAY FROM ALL COMBUSTIBLE MATERIALS, PENDING FINAL DISPOSAL.
Eco-65 Installation and Operation Manual FIREBOX CLEARS AND BLOWERS SHUT DOWN. DO AS INSTRUCTED IN “EVERYDAY STARTUP” THEN ATTEMPT TO RESTART THE STOVE. IF THE PROBLEM PERSISTS, CONTACT YOUR DEALER. NOTE THAT SMOKE BUILD-UP DURING IGNITION MAY OCCUR. SMOKE CAN ACCUMULATE IN THE FIREBOX FOR A FEW SECONDS JUST BEFORE THE IGNITOR IS HOT ENOUGH TO FIRE-UP THE PELLETS IN THE BURN POT. THIS IS NORMAL. AS SOON AS THERE IS FIRE IN THE BURN POT, SMOKE WILL DISAPPEAR. MAINTAIN PROPER VENTILATION.
Eco-65 Installation and Operation Manual 4.8 Combustible 4.8.1 Proper Fuel Each type of pellet has its properties and will burn differently. The amount of ashes produced can also vary greatly. Conventional pellets are those ¼” or 5/16” in diameter and not over 1” long. Longer or thicker pellets will affect the constancy of pellet feed. For example, if the pellets are very short, they will have more ease to accumulate and pile into the feed screws.
Eco-65 Installation and Operation Manual 5 Stove Controls 5.1 Control Panel The blowers and automatic fuel supply are controlled from a control panel (A) on the righthand side of the ECO-65.
Eco-65 Installation and Operation Manual Control panel screen Operation mode : OFF MANUAL Button to select between modes Button to change the convection fan speeds THERMOSTAT: Thermostatic control (optional) Button to clear most error codes Button to feed and start when the auger is empty Pellet burn rate Button + and – allows to select the heat level 5.1.1 Mode Button When the mode switch is pressed, you will be able to choose the Manual or the Thermostat mode, or to turn off the appliance.
Eco-65 Installation and Operation Manual 5.1.2 Fuel Feed Button When the “Fuel Feed” button is pushed the stove will feed pellets continuously into the burn pot during 1 minute and then the ignition cycle will begin. The “Feed and Start” message will appear. Use this option when you start your stove for the first time in the season or when the stove has run out of pellets, i.e. the hopper is empty. The auger will turn and then the stove will start automatically an ignition cycle.
Eco-65 Installation and Operation Manual 5.2 Adjustments 5.2.1 Selecting the Combustion Level (Heat Rate) The heat input of the stove varies between 10,500 BTU/h to 65,000 BTU/h. To change the combustion level select the + or – button when the stove is in function. Note: Input range may vary according to the type of pellets being used.
Eco-65 Installation and Operation Manual 6 Stove Operation 6.1 First Startup Before starting your stove, make sure that the burn pot, the baffle and the maintenance access panels are properly installed. Make sure that the stove has been emptied of all tools and accessories (see Section 2.3: Before Operating Your Stove). Also make sure that the venting system is properly sealed, that all doors and hopper lid are closed. Make sure that the hopper is full of pellets. Press the auger button .
Eco-65 Installation and Operation Manual 6.5 Shutting Down Procedure To turn your stove off, press the button on the control panel until the LED light is in the OFF position. The cooling cycle will take a few minutes and the blowers will continue to function while the stove is cooling down. IMPORTANT: DO NOT DISCONNECT THE POWER CORD TO TURN OFF THE STOVE. 6.
Eco-65 Installation and Operation Manual 6.7 Signs of an Overheating Stove Under normal conditions, the flame should have a bright yellow color and be very active, but stable. If you see the flame getting lazy, very high and orange, it may be a sign that there is something wrong. Usually, overheating issues are caused by too much restriction in the venting system, a blocked heat exchanger, a lack of combustion air or a lack of maintenance. If this happens, your stove will become very hot.
Eco-65 Installation and Operation Manual 7 Maintenance 7.1 Stove Maintenance 7.1.1 Recommended Maintenance Schedule Use this as a guide when used under average conditions.
Eco-65 Installation and Operation Manual 7.1.2 Cleaning the Baffle, the Heat Exchanger and the Combustion Chamber Cleaning of the heat exchanger must be done on a regular basis (see Section 7.1.1: Recommended Maintenance Schedule). To access the heat exchanger you need to first rise up and pull towards you the decorative grill (A) above the viewing door. Unscrew the two wing nuts (B) and remove the access panel (C) to the heat exchangers.
Eco-65 Installation and Operation Manual Using the provided sweeping rod, sweep up and down each exchanger. Make sure you go all the way down to the bottom. Reinstall the access panel to the combustion chamber and tighten the wing nuts. DO NOT USE PLIERS OR OTHER TOOLS TO TIGHTEN THE WING NUTS. To clean the baffle, pivot the lock plate by 90° found above the access door of the combustion chamber. The baffle will rotate and drop the accumulated fly ash. Clean and reinstall the baffle.
Eco-65 Installation and Operation Manual 1) Open the door and turn the lock (A) that can be found above the door opening. 2) Once the baffle (B) is unlocked, it will pivot downwards automatically. 3) Lift the baffle (B) from its pivots (C). Pull it down.
Eco-65 Installation and Operation Manual 4) Take out the baffle from the combustion chamber. IT IS HIGHLY RECOMMENDED TO CLEAN THE EXHAUST CHANNEL (SEE SECTION 7.1.3: EXHAUST CHANNEL AND EXHAUST BLOWER MAINTENANCE) IMMEDIATLY AFTER CLEANING THE HEAT EXCHANGER. 7.1.3 Exhaust Channel and Exhaust Blower Maintenance Exhaust channels and the exhaust blower are located on the left hand side of the stove.
Eco-65 Installation and Operation Manual Using a Philips or Robertson screwdriver, remove both clean-out traps by unlocking them. Push the screw and give it a counter-clockwise quarter turn. Locate both openings. Using the provided scraper, remove the dirt in the bottom channel of the heat exchangers. Use an ash vacuum to complete the cleaning operation. Make sure that the gaskets are still in good condition, replace them if needed.
Eco-65 Installation and Operation Manual 7.1.4 Cleaning the Burn Pot The burn pot must remain clean and the holes should not be obstructed by combustion residues (ashes or clinkers). 1. Clean the burn pot using the scraper provided with the stove or a smaller one.
Eco-65 Installation and Operation Manual 2. The burn pot simply sits onto the air intake channel. You must lift to remove it from the stove. Two small pins guide the burn pot in place. Make sure that the burn pot is well in place before turning on the stove (as shown in the diagram). 3. If necessary, clean the air intake channel. To reach the air intake channel clean out trap, open the ash drawer access door and remove the ash drawer (A). 4. Unscrew the wing nut (C) to open the clean out trap (B).
Eco-65 Installation and Operation Manual Verify that the clean out trap gasket is still in good condition, replace it if needed (3/16’’ black round gasket, AC06815). 7.1.5 Ash Removal 1. To empty the ash drawer (A) of its contents, open the ash pan access door by loosening the round knob on the bottom left hand side. 2. Empty the ash drawer, vacuum around the drawer and at the bottom of the combustion chamber.
Eco-65 Installation and Operation Manual 7.1.6 Cleaning the Air Wash System Vacuum the ashes that may have accumulated into the airwash system inlet between the bottom glass retainer and the glass. This will allow an optimum air flow along the inside portion of the glass and prevents the glass from sooting-up. 7.1.7 Glass Care Clean door glass when necessary. The use of a stove glass cleaner is recommended. Regular household glass cleaners will not remove creosote properly.
Eco-65 Installation and Operation Manual 7.1.9 Door Gasket Maintenance It is important to maintain the door gasket in good condition. After a while, the gasket will wear and compress; adjusting the door may then be required. If the door adjustment is not sufficient, replace the door gasket with a genuine part. If the stove door is not properly sealed, it will be difficult to keep the door glass clean and combustion gases may leak into the room. 7.1.
Eco-65 Installation and Operation Manual 7.2 Venting System Maintenance CAUTION: REGULARLY EXAMINE THE VENTING SYSTEM, THE JOINTS, AND THE SEALING TRIMS TO ENSURE THAT THE SMOKE AND THE COMBUSTION GASES ARE NOT DRAWN BY THE CONVECTION BLOWER. The most efficient method to sweep the venting system is by using a 4'' pellet brush depending on your installation.
Eco-65 Installation and Operation Manual 8 Troubleshooting When you have issues with your stove, your first reaction may be to call technical support. This section will help you save time and money by enabling you to solve simple problems by yourself. Most common problems are generally caused by the following five factors: 1. 2. 3. 4. 5. Wrong operation or lack of maintenance; Bad installation; Poor quality combustible; Component failure; Factory defect.
Eco-65 Installation and Operation Manual 8.2 Testing a Component If you suspect that an electrical component to be defective, you can test it by following the procedure given below. Note that you will be able to test only components when the stove is OFF and that all the components are no more in function. (Take note that the software versions given below are an example only and may not reflect the actual software versions of your stove.
Eco-65 Installation and Operation Manual Push the control key to proceed. The frequency of the power source is displayed. Push any control key to proceed. The tension of the power source is displayed. Push any control key to proceed. Displays if polarity is good (POLP) If polarity is reversed (POLF). Push any control key to proceed. The version of software included in the control board is displayed. Push any control key to proceed. Displays the status of different components.
Eco-65 Installation and Operation Manual Displays the temperature read by the thermistor. Push any control key to proceed. Convection blower test. Push the control key to proceed. Combustion blower test. Push the control key to proceed. Exhaust blower test. Push the control key to proceed. Ignitor test. Push the control key to proceed. Auger# 1 test. Push the control key to proceed. Auger#2 test. Push the control key to proceed. Validate the absence of an SD card in the reprogramming port.
Eco-65 Installation and Operation Manual 8.3 Main Error Codes, Possible Causes and Solutions WARNING: RISK OF ELECTRICAL SHOCK. IF YOU NEED TO MANUALLY TEST, MANIPULATE OR REPLACE ANY COMPONENTS, THE STOVE NEEDS TO BE DISCONNECTED FROM THE WALL OUTLET. This section contains main error codes, possible causes and many suggestions to guide you in resolving them. After giving an error code, your stove will shut down by itself and start a cool down cycle.
Eco-65 Installation and Operation Manual 8.3.1 P Code STOVE SHUTS OFF AND APPEARS ON CONTROL BOARD Possible possible) Possible Causes: Remedies: (Unplug stove first when 1. Pressure tap (located on the Pull off the air hose from the exhaust blower pressure exhaust blower) is blocked. tap and from the negative (white) pressure switch tap. WARNING: THE TUBE MUST ABSOLUTELY BE DISCONNECTED FROM THE PRESSURE SWITCH AS TO NOT DAMAGE IT.. Blow in the air tube. If air flows freely, the hose is fine.
Eco-65 Installation and Operation Manual 8. Pressure switch (very rare). 52 is defective Even though this situation is highly unlikely, it’s possible the pressure switch is defective. To test the airflow pressure switch, you need to disconnect the air hose from the blower casing. With the other end still attached to the switch, very gently suck on the loose end of the hose (you may want to completely disconnect the hose from the stove and the switch first and make sure it is clear).
Eco-65 Installation and Operation Manual 8.3.2 H Code STOVE STOPS FEEDING PELLETS AND APPEARS ON THE CONTROL BOARD. BEFORE RESETTING TAKE CARE IN READING THE POSSIBLE CAUSES AND THEN PRESS ON AND AT THE SAME TIME FOR 2 SECONDS. Possible Cause: Possible Remedy: 1. Inadequate fuel is used. Remove the burn pot, make sure that all openings are clear and check that no ash has filled the tube around the igniter. Refer to the maintenance section.
Eco-65 Installation and Operation Manual NOTE: IF THE CODE APPEARS MORE THAN THREE TIMES, THE ERROR CODE WILL LOCK ITSELF UP. THIS PELLET STOVE IS EQUIPED WITH MULTIPLE DEVICES TO ENSURE YOUR SAFETY. IF A WARNING ERROR CODE STOPS YOUR STOVE ON SEVERAL OCCASIONS, IT IS MORE THAN LIKELY THAT THE STOVE DOES NOT EXHAUST PROPERLY. COMPLETE the stove maintenance as described in this manual before resetting the electronic board displaying an error code.
Eco-65 Installation and Operation Manual 8.3.3 E Code STOVE SHUTS OFF AND DISPLAYS WARNING CODE Possible Causes: Possible Remedies: (Unplug stove first when possible) 1. The stove ran out of pellets. Refill the hopper. Erase the error code and press the auger button (see Section 5.1.2: Fuel Feed Button). 2. The burn pot holes are blocked. Remove the burn pot and clean it thoroughly. 3. The air intake, the inner parts of Follow instructions in the Maintenance section.
Eco-65 Installation and Operation Manual 5. The flue temperature sensor failed. The “thermistor” is a heat sensor located on the exhaust motor housing. Its function is to tell the control board that the stove has ignited properly by measuring the heat at the exhaust. The pellet stove will not start feeding pellets at the desired heat setting until it has received a signal from the thermistor heat sensor. If the thermistor heat sensor is faulty, the unit will stop after the ignition cycle.
Eco-65 Installation and Operation Manual HOPPER AUGER A Screws B Auger and motor assembly C gasket BURN POT AUGER A Screws B Auger and motor assembly C GASKET 57
Eco-65 Installation and Operation Manual 8.3.4 L Code STOVE FEEDS PELLETS, BUT WILL NOT IGNITE AND CONTROL BOARD APPEARS ON THE Possible Causes: Possible Remedies: 1. Inadequate fuel is used. Remove the burn pot, make sure that all openings are clear and check that no ash has filled the tube around the igniter. Refer to the maintenance section. Also, make sure that recommended fuel is used (see Section 4.8.1: Proper Fuel). 2. The igniter is defective. See Section 8.
Eco-65 Installation and Operation Manual 8.3.5 d Code STOVE STOPS FEEDING PELLETS AND Possible Cause: APPEARS ON THE CONTROL BOARD Possible Remedy: 1. The hopper lid has stayed open for more As a security measure, the auger stops than 3 minutes. turning and feeding pellets as soon as the hopper lid opens. It will resume normal operation as soon as the hopper lid is closed. If the hopper lid stays open for more than 3 minutes, the stove will stop. 2.
Eco-65 Installation and Operation Manual 8.3.8 I Code STOVE FEEDS PELLETS, BUT WILL NOT IGNITE AND CONTROL BOARD Possible Cause: APPEARS ON THE Possible Remedy: 1. The igniter fuse on the Test the resistance (ohms, Ω) with a multimeter. If the control board has blown. value is near zero, replace the igniter and the F3 fuse. 2. The wiring shorted. harness Inspect the wiring and replace any defective wire and or connector. Make sure the wires are not shorted to the stove frame.
Eco-65 Installation and Operation Manual 8.3.10 Smoke Smell SMOKE SMELL COMING BACK INTO THE HOME Possible Causes: Possible Remedies: 1. Venting system leaks. Inspect all vent connections. This is a pressurized venting system. All vent connector joints must be sealed and fastened in accordance with the pellet vent manufacturer's instructions to ensure consistent performance and avoid smoke and ash spillage (see Section 4.5.1: Installation Warnings, Cautions and Recommendations Reminder). 2.
Eco-65 Installation and Operation Manual 8.3.11 Auger Motor Stops Momentarily AUGER MOTOR STOP FEEDING PELLETS AND COMES BACK ON Possible Cause: Possible Remedy: 1. The auger motor is overheating and It’s possible that the auger is jammed. tripping the internal temperature shutoff Remove it from its housing (see drawing (thermal protector). Section 8.3.3: E Code).
Eco-65 Installation and Operation Manual 4. Air intake channel is Visually inspect the air intake channel that leads to the burn pot for restricted. foreign material. Make sure that the air-intake shutter is functional and free of any obstruction. 5. The combustion/exhaust blower failed. See Section 8.2: Testing a Component and test the combustion and the exhaust blowers independently. If one of them does not function, make sure there is power and that the blowers are properly connected.
Eco-65 Installation and Operation Manual 9 Wiring Diagram 64
Eco-65 Installation and Operation Manual 10 Access to Fuses WARNING: UNPLUG THE STOVE BEFORE CHANGING THE FUSES. All fuses are located inside the housing of the electronic board; the housing is on the back of your stove. Unplug your stove, remove the screw and turn the four spring clips to open the housing.
Eco-65 Installation and Operation Manual LETTER A B C D E F G 66 FUSE FUNCTION MAIN BOARD FUSE CONVECTION BLOWER COMBUSTION BLOWER EXHAUST BLOWER TOP AUGER #1 BOTTOM AUGER #2 IGNITOR AMPERAGE 7.
Eco-65 Installation and Operation Manual 11 Components Location LETTER COMPONENT A HEAT EXCHANGER TUBES B BURN POT C IGNITOR D CONVECTION BLOWER E THERMISTOR F L-250 THERMAL SWITCH G HOPPER H CONTROL PANEL I HOPPER SAFETY SWITCH J PRESSURE SWITCH K F-160 THERMAL SWITCH L POWER CORD RECEPTACLE M O THERMOSTAT TERMINAL BLOCK COMBUSTION BLOWER/FRESH AIR INTAKE EXHAUST BLOWER P BOTTOM AUGER #2 Q TOP AUGER #1 R ELECTRONIC BOARD N 67
Eco-65 Installation and Operation Manual 12 Blower Replacement CONVECTION BLOWER Unscrew screw A (1), slightly pivot the fan upward then partially slide the fan out (2). Disconnect the fan from the harness and remove completely.
Eco-65 Installation and Operation Manual COMBUSTION BLOWER Remove the 9 screws (A) and the bottom grille (B). Unlatch the clamps (C). Remove the back draft shutter (G) and the gasket (D). Pull the combustion blower (F) and unplug the wire connector from the harness. Remove the plug (E) of the blower.
Eco-65 Installation and Operation Manual EXHAUST BLOWER Remove the left panel. Unplug the connections (A) and (B). Unplug the silicone tube (C).
Eco-65 Installation and Operation Manual Remove the clamp (D). With a Philips screwdriver, unlock and remove the access panel (E).
Eco-65 Installation and Operation Manual Remove the nuts (F) located in the opening of the trapdoor. Remove the duct assembly (G).
Eco-65 Installation and Operation Manual Remove the bolts (H) and nuts (I) to remove the exhaust blower (J) 73
Eco-65 Installation and Operation Manual 13 L-250 and F-160 Thermal Switch Replacement L-250 1. Remove both retaining screws (A) holding the thermal switch support bracket (B). 2. Lift up the support bracket. Rotate the bracket 90° clockwise then pull the bracket toward you.
Eco-65 Installation and Operation Manual Remove the faulty thermal switch. Replace new thermal switch (D) underneath the bracket (B) by means of 2 screws (C). F-160 Unscrew both screws (B) and take out the thermal switch F-160 (A).
Eco-65 Installation and Operation Manual 14 Exploded View and Replacement Parts SECTION A 76
Eco-65 Installation and Operation Manual SECTION B 77
Eco-65 Installation and Operation Manual SECTION C 78
Eco-65 Installation and Operation Manual SECTION D SECTION E 79
Eco-65 Installation and Operation Manual SECTION F SECTION G 80
Eco-65 Installation and Operation Manual SECTION H SECTION I 81
Eco-65 Installation and Operation Manual SECTION J SECTION K 82
Eco-65 Installation and Operation Manual IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your stove, please provide the model number and the serial number. We reserve the right to change parts due to technology upgrade or availability. Contact an authorized dealer to obtain any of these parts. Never use substitute materials. Use of non-approved parts can result in poor performance and safety hazards and will void your warranty.
Eco-65 Installation and Operation Manual # Item 36 PL67173 BAFFLE EXTENSION 1 37 30799 STEEL ROUND KNOB, 3/8"-16 THREADED 1 38 30800 FULLY THREADED STEEL EYE BOLT, 3/8"-16 1 39 SE67151 ASH DRAWER ACCESS DOOR 1 40 AC06825 GASKET KIT SELF ROUND BLACK 3/4" 1 41 30055 HINGE PIN RETAINING RING 5/16" ID X 0.512" OD 2 42 30167 HINGE PIN 5/16 DIA.
Eco-65 Installation and Operation Manual # Item Description Qty 76 44015 FUSE 5A / 250V / 1/4" DIA. X 1 1/4'' L 2 77 44016 FUSE 3A / 250V / 1/4" DIA.
Eco-65 Installation and Operation Manual Possible Vertical vent length (feet) APPENDIX A: HORIZONTAL AND VERTICAL VENT CHART Possible Horizontal vent length (feet) For example, let’s imagine an installation consisting of a horizontal vent coming out at the back of the stove on a total distance of 8 feet. This horizontal run is followed by a tee and a 6-foot vertical rise. This type of installation is not acceptable.
Eco-65 Installation and Operation Manual Instead, if the installation consisted of a horizontal vent coming out at the back of the stove on a total distance of 4 feet, followed by a tee and a 6-foot vertical rise, it would be acceptable. The termination is within the allowable configuration zone on the chart since it would have at least one foot of vertical rise for each foot of horizontal run. Furthermore, the total vertical rise is at least 3-feet high.
Eco-65 Installation and Operation Manual APPENDIX B: INSTALLING A THERMOSTAT (AC05558) Using a thermostat will help you maintain a constant temperature throughout the house. A low voltage thermostat (24 volts) is required. A fixed wall mount or hand held model can be used. Note: Thermostat manufacturer’s instructions always override the information published in the following section. Thermostat location Location of the thermostat is very important to obtain comfort and efficiency from your stove.
Eco-65 Installation and Operation Manual Wired thermostat Before installing the thermostat, unplug the power cord from the power outlet. First, connect the two thermostat wires to the terminal block located at the rear on the right hand side of the stove when facing it. Loosen the two middle screws and insert the wires in the terminals. Tighten the two screws. Open the thermostat and connect the wires as per the manufacturer’s instructions.
Eco-65 Installation and Operation Manual Wireless thermostat If you are using a wireless thermostat or a hand held thermostatic remote control, connect the two thermostat wires to the terminal block located at the rear on the right hand side of the stove while facing it. If the receiver wires are equipped with quick-connect terminals you can connect them directly to the stove’s wiring harness.
Eco-65 Installation and Operation Manual APPENDIX C: MOBILE HOME INSTALLATION Anchor the stove WARNING: FOR MOBILE HOME INSTALLATION, IT IS MANDATORY TO CONNECT THE STOVE TO AN OUTSIDE COMBUSTION AIR SOURCE. (SEE APPENDIX D: COMBUSTION AIR SUPPLY). When installed in a mobile home, the stove must be anchored to the floor with two screws. Use the two anchoring holes (A) located for this purpose on each side of the pedestal, as shown on the following image.
Eco-65 Installation and Operation Manual 92 A Fresh air intake B Tee C Pellet pipe length and/or slip section D Ceiling support E Attic insulation shield F Roof flashing G Storm collar H Pellet pipe length I Vertical rain cap
Eco-65 Installation and Operation Manual APPENDIX D: COMBUSTION AIR SUPPLY WARNING: FOR MOBILE HOME INSTALLATION, IT IS MANDATORY TO CONNECT THE STOVE TO AN OUTSIDE COMBUSTION AIR SOURCE. INSULATED PIPE SHOULD NEVER EXCEED 10 FEET. It is recommended to install an outside air inlet in or near the room where the stove is installed. When doing so, it is preferable to choose a wall which is not exposed to dominant winds, depending on the conditions surrounding your house.
Eco-65 Installation and Operation Manual To complete the installation, make a hole of1/4" to 1/2" (6 mm à 13 mm) bigger than the insulate pipe diameter in the outside wall of the house at the chosen location. From outside, place the outside air inlet cap (E) in the hole (open side down) and fasten the register to the wall, with screw. Place the insulated pipe (A) over the register tube and over the fireplace outside air connector (D).
Eco-65 Installation and Operation Manual Sources of Outside Combustion Air WARNING: IT IS FORBIDDEN TO DRAW COMBUSTION AIR FROM A BASEMENT, AN ATTIC, A GARAGE OR ANY CONFINED SPACE. You can draw air from a ventilated crawl space underneath the floor. You can draw air directly from an outside wall, behind the stove.
Eco-65 Installation and Operation Manual APPENDIX E: OPTIONAL HOT AIR PLENUM KIT (AC01330) The hot air plenum kit AC01330 is available at your local dealer. Please note that the 3.25” x 10” duct is sold separately. Duct 3.
Eco-65 Installation and Operation Manual This hot air plenum kit contains the following parts: (A) -49068 (B) -PL62444 2x 1x (D) -PL62446 (5” x 17.
Eco-65 Installation and Operation Manual DROLET LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original retail purchaser and is not transferable. This warranty covers brand new products only, which have not been altered, modified nor repaired since shipment from factory. Proof of purchase (dated bill of sale), model name and serial number must be supplied when making any warranty claim to your DROLET dealer. This warranty applies to normal residential use only.
