PillowFit Deluxe Nasal Pillow CPAP System REF 100NP 100NP-NH CAutioN : Federal (U.S.) Law restricts this device to sale by or on the order of a physician.
PILLOWFIT DELUXE NASAL PILLOW CPAP MASK REF 100NP 100NP-NH Intended Use The PillowFit Deluxe nasal pillow mask CPAP system is intended to provide an interface for Continuous Positive Airway Pressure (CPAP) or bi-level system. The mask to be used by adult patients (>66Ib/ 30kg) for whom positive airway pressure has been prescribed. The mask is for single-patient re-use in the home environment and with proper cleaning multi-patient re-use in the hospital/ institutional environment.
Parts of the Pillow t Deluxe Nasal Pillow CPAP Mask System No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Fitting your Nasal PillowFit Mask Attach the pillows on the platform. Make sure the tenons are tted. Your new PillowFit will already have the pillows attached. Attach the pillow set into the main frame. Make sure the platform concave is tted to the main frame protuberance. Match the L and the R on the platform to the L and R on the frame. Plug the tube into the main platform.
Fitting your PillowFit Deluxe Nasal CPAP System -4-
Fitting your PillowFit Deluxe Nasal CPAP System Insert the head strap B1 into A1 and fasten it. The same with the other side. Insert the head strap B2 into A2 and fasten it.
Fitting your PillowFit Deluxe Nasal CPAP System The same with the other side Both head straps are now tted. Hold the pillows at your nose, and pull the headgear over your head.
Fitting your PillowFit Deluxe Nasal CPAP System Adjust top straps (over tightening may cause excess pressure on your nose). Adjust each end of the back strap. Adjust the angle of the pillow to ensure it sits comfortably.
Fitting your PillowFit Deluxe Nasal CPAP System Now the nasal pillow mask is tted and ready for use. Fasten the air tubing through top strap. The tubing can be positioned in the center. If the pillow mask pulls on your nose, increase length of tube between mask and top strap.
Cleaning the interface: The cushion, nasal interface, and tubing should be cleaned daily or as needed. • Hand wash in warm water with a mild liquid dish washing detergent. Do not use bleach, alcohol, or cleaning solutions containing alcohol. Do not use cleaners containing conditioners or moisturizers. • Rinse thoroughly. Pat with a towel and air dry completely before use. • Inspect all parts for damage or wear; replace if necessary. Cleaning the Headgear: Hand wash the headgear weekly or as needed.
Technical Specications Pressure-Flow Curve 4 cmH2O Note: The mask contains passive venting that meets the requirements for protection against rebreathing as specied in ISO 17510-2. As a result of manufacturing variations, the vent ow rate may vary. 8 cmH2O 12 cmH2O 16 cmH2O20 cmH2O ĵı ĴĶ Ĵı ijĶ ijı IJĶ IJı Ķ ı ĵĹ cmH2O IJij IJķ ijı cmH2O cmH2O cmH2O cmH2O Standards CE designation in accordance with EC directive 93/42/EEC, class Iia. ISO 14971, ISO13485, ISO 10993-1 and ISO 17510-2.
Manufactured for: Drive Medical 99 Seaview Blvd Port Washington, NY 11050 Toll-Free 877-224-0946 www.drivemedical.
