4.4 VOLT CORDLESS COMBO PACK 40056 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright © 2002 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353 40056 combo pack.
Specifications Drill Circular Saw Reciprocating Saw Flashlight Batteries Charger Accessories 0 ≅ 550 RPM 3/8 inch keyless chuck Variable speed Switch Forward / Reverse Switch 6 torque settings 2400 RPM Saw Blade Size 5-3/8” 1-1/2 inch cut depth at 90 degrees 1-1/4 inch cut depth at 45 degrees Bevel: 50 degree 200 output watts 0-2800 SPM Stroke: 7/8 inch 90 degree swivel head Two 14.4 VDC batteries provided 120 VAC (input) 3 to 5 hour charging time, 1.
6. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working.
Note: Performance of these tools (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Drill Operation 1. Insert a drill or screw bit into the Chuck (8). Securely tighten. Turn the chuck counterclockwise to open, and clockwise to close while holding on to the chuck sleeve. Use 3/8 inch bits or smaller to avoid damage to gears and motor. 2. Set the desired drill torque by turning the Torque Selector to setting 1 to 6. The higher the number, the more the torque. Use # 6 for drilling, and the others for driving. Do this when the drill if off. 3.
5. Insert saw blade through the base with teeth facing forward (and up) until the center holes of the saw blade and motor adapter (5A) align. (Notice the arrow on the movable guard and the arrow on the saw blade, they should be pointing in the same direction.) 6. Replace washer (2A) and nut bolt (1). Tighten with hex key (48A) while pressing on the stop button (1A7). Verify stop button is in the up (unlocked) position. 7. Replace key to its storage hole in the housing of the saw.
Cutting Warning: this tool can cause serious injury if not used properly. Read this entire manual before using. Note: The moveable Guard (#8A) must be in place at all times. Note: verify that saw blade is securely tightened and both angle and height adjusting knobs are tight. 1. Secure rip fence or straight edge to the material to guide the saw on a straight path. 2. Place the saw base (50A) on material to be cut. Align the front notch (right edge aligns with saw blade) on the cut line. 3.
Caution: Avoid possible injuries while carrying the reciprocating saw. Lock the Trigger Switch in the off position by pressing in on the Trigger Switch Lock (14B). 3. With the blade installed, press the Switch Lock to lock the Trigger Switch. Squeeze the Trigger Switch. It should not move. 4. After the Battery is charged, insert into the housing. 5. To turn the saw on, press the Switch Lock in the opposite direction, then squeeze the Trigger Switch. 6. Prepare and secure the material to be cut.
7. Store these tools in a clean and dry area. Avoid storing in high temperature areas. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activites, contain chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm.
Drill Assembly Drawing Battery Charger (#21) PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Circular Saw Parts List A A = A = ' ] A ! A ` _ = A % A < A A ! A " $ + A > {+ %A < A > {+ < A & ' * A ] = + A * & A > {+ < A < A | ' A = A > $ " $
Circular Saw Assembly Drawing 66 NOTE: Part numbers for Circular Saw parts have an “A” suffix. Please include this suffix when ordering replacement parts. SKU 40056 40056 combo pack.
Reciprocating Saw Parts List ITEM 1B 2B 3B 4B 5B 6B 7B 8B 9B 11B 12B 13B 14B 15B 16B 17B 18B 19B 20B 21B 22B 23B 24B 25B 26B DESCRIPTION QTY Saw 1 Washer 1 Snap Washer, 5 1 Stud Screw, M5x12 1 Screw, M4x14 3 Snap Washer, 4 3 Adjustable Pad 1 Pin, A5x14 2 Flange 2 Snap Washer, 4 13 Screw, ST 4.
Reciprocating Saw Assembly Drawing 20 NOTE: Part numbers for Reciprocating Saw parts have an “B” suffix. Please include this suffix when ordering replacement parts. SKU 40056 40056 combo pack.
Flashlight Parts List C ? $ = C ` _ = C ` = & ? $ C ` C ' ! C ` ? _ % C ' } C = $ \ + C = +C >
Flashlight Assembly Drawing NOTE: Part numbers for Flashlight parts have an “C” suffix. Please include this suffix when ordering replacement parts. SKU 40056 40056 combo pack.
