Installation Instructions for Shower kit Modal : DK111088 SAVE THIS GUIDE FOR FUTURE REFERENCE. Bar code : 0855343443870 Read all instructions carefully before proceeding.
# General Information Please inspect the product immediately upon receipt for transit damage, missing packs / parts or manufacturing defects. Damage reported later cannot be accepted. Please handle the product with care to avoid knocks and shocks on any side or edge of the glass. Note: The safety glass cannot be re-worked. Please read these instructions carefully before starting the installation. Special care should be taken when drilling the walls to avoid hidden pipes or electrical cables.
1°2 D2 Parts and components BIg Stammer B1'6 ~~ i AdB 8i4x30mm { i nme Destitution uty | ho ner Description unity i Top & boil rail z Bi Wal plugs iz 2 Ill profits 2 C1 Screw Covers 8 3 Fixed panel Z 1 Fixed panel seals A 2 5 Hiding doors 2 02 Movable panel seals B 2 8 Wal pearls 2 D3 PVG magneto dace sale 2 7 Decorative column 1 E1 Plastic covers A Fl 8 Bas 1 E22 Plastic cover B.
Fig. 1 Fig. 1a Fig. 1b Preparation of the shower installation area 36" 53/8 Fig.1 For a new construction and whenever possible in the case of a renovation, install an extra stud in each wall. Each stud has distance of 36" (914mm) from the wall's corner. Fig. 1 Figaro For the stud distribution, please refer fo Fig. 1a and Fig. 1b. Te livid the floor, use a self-leveling mortar.
Preparation of the shower installation area Fig. 2 it board maxi thick Cement board maximum 174" hi Note: The base has to be installed against the studs not the finished walls. The finished walls No must not exceed. 1/4" thick. if necessary, remove the wall covering to expanse the studs. Fig, 2. Confirm that the walls are vertical using a plumb fine within 3/8" square, and that the floor is level. Fig. 2. 3 (76.5mm) Fig. 3 a Fig.
DEICE of shower area Fig. 4 Strainer A { Wrench Key a Caulking nut Rubber caulking gasket | ' Main body of the Rubber gasket Cn Friction ring Bottom of the base Fig. 5a Figaro Install the base directly against the studs and | make sure that the drain pipe is centered with the drain head. The base has to be leveled in all directions. Please refer to the drain Installation guide.
Base installation #Bx 11/4" Fig. 5b q =) Flat head craw (recommended) important: Hard tighten only! Note: Use shims behind the fastening flange as required. Bx 14 sowers, re With a 316° bit, dr holes In the base flange, then secure the base onto the wall studs with Note: The wail panels should be installed at a temperature near and must not be installed in unheated areas where temperatures might drop below 0 °C {32 °F), i The wall panels can be Installed over drywall, plaster, Fig.
Wall Installation Fig. 7a Figaro Measuring from the shower base to the drawn line on the wall, determine the Location of the plumbing fixtures. Cut or drill the fixture holes in the wall panel. lf a knife is used, make sure that it is properly sharpened. Do not try to cut through the plastic all at once; score it over and over, cutting a little deeper each time until you reach the other side.
Decorative Column Installation Figaro Apply the adhesive on the rubber strip and install the shower wall pane! onto the rubber strip as shown on the illustration. Fig. 8b Cut a 1cm nozzle off the adhesive cartridge from the end at a 90° angle toward the tip. In no case should the adhesive bead be larger than a standard pencil diameter, which is 5mm Apply the adhesive on the back (matte side) and position the panel on the back wall. See ADHESIVE INSTRUCTIONS for installation procedure. Fig.
Decorative Column Installation Fig. 8d hl Fig. Bd Install the second shower wall panel as shown on the Illustration. ; i Figure Apply silicone to caulk the { 3 . joint between the wall panel and the base. Fig.9 Apply some silicone an the decorative column and install ihe rubber strip as illustrated.
Glass shelves installation When installing the faucet's face plate or any other component, make sure to apply some silicone on the outer edge. Fig. 10b —~ 7° 6.0mm’ Fig. 10d Figaro Place the shelf In the comer of the shower where you want to install it. Using a pencil, 8 marker or a wax crayon, mark the spots where you will drill the holes for the shelves. Drill the holes using a 1/4" drill bit. Fightback Apply some silicone in the previously drilled holes on the side and back walls.
Shower door Installation Fig. 11a Figaro Position and level both wall jambs at 3/4" from the outside edge of the shower base and mark the fastening holes. Fightback Remove the wall jambs and drill a hole where you find each marked position. i Fightback Insert the wall plugs into the holes using a hammer. { Figured Apply the silicone sealant behind the wall jambs and fasten them onto the wall with the provided screws.
Shower institutionalization Fig. 12 Fig. 12 Install the bottom rail on the panel tracks using the screws, as shown on the illustration.
Shower Door Installation Fig. 13 Fig.13 Install the top rail on the panel i tracks using the screws, as shown I © on the illustration.
Shower Door Installation Fig. Fig.14 Insert the fixed panels in the | wall jambs as Shawn. To confirm the position of the components, make sure that the glass is parallel to the base.
} Shower Door Installation Fig. 15 Fig.
Fig. 19 Shower Door Installation Fig. 19 Fig. 20 Adjust the screws on the top wheel to ensure that the sliding door can move smoothly. The magnetic door seals should close flush with each other. Install the handles on the sliding doors.
Shower Door Installation i Fig. 27a Drill through 1/8” holes in the! panel tracks as shown on the | illustration. : Fig. 21 b Fasten the door frame on the ; } I wall profile with screws, ! Fig. 21 ¢ Install the caps on the screws. : Fig.
Shower Door Installation Fig. 22b Fig.23 Caulk the joint between the fixed */ | Fig.22 Install the top rail caps as shown. \ | glass panel and the bottom rail. i | Fig.24 Apply a 100mm silicone sealant line at the bottom between | the wall profile and the fixed panel | track, | Wait 24 hours before using the shower.
Wye certify that aur products will meet your needs with their style, but also with their manufacturing quality. To make sure that they are reliable and safe, each product was carefully inspected, tested and approved during the quality control process that is in place.
