Installation & Assembly

ManualsBrandsDreamSpa ManualsBathroom Remodel & Bathroom FixturesShower Combo

`ZPz

To (onnec'

3 way Show

4-A

;#®

1. Remove old shower head. Strew Lock Nut, with single Inner Thread

fo(,#y;A>©`

lNNER THREAD

YOU, onto showei arm to end of its thieod, but D0 NOT tighten (Fig.I ).

2. S(Few Water Diverfer with Thick Washer in place onto Shower Arm stopping

ot lost possible position when Hose Outlet is facing DOWN (Fig. 2).

3. Countem.ghten Lock Nut in ieverse diredion, until it presses

fl.ghfly ogoinst Diverter, thereby lo{king it in this posifl.on.

4. Remove protective (op off Shower Head Nut and make sure

Washer Tests fltlt inside Nut.

Then s(lew Shower Head onto Front Outlet (Fig. 2) .

5. Turn ON water to test connection. If leokoge o(curs, dis(onnect

Diverter and odd Thin Washer (spore) to Thi(k Washer olreody

inside its ne(k (Fig. 3), then ie{onnect and test qgoin.

lf Leokqge Otturs Due to Short Shower Arm

Threads, D0 NOT Use Lo(k Nut

Tostopleqkoge,yourShowerArmendmustohaysieochWosher

inside Divener and press against it. If your Shower Arm with Lo(k

Nut on it does not hove enough threads to reach Thi(k Washer

inside Oiverter, remove Lock Nut and D0 NOT use it.

Add Thin Washer to Thick Washer, .rf needed, for better alignment

IThin Washer (ompensotes for about 1 /2 thioud turn).

6. Screw Hose end nut with Hose Washer in place onto Hose Outlet

(Fig. 4). Strew other Hose end nut with Hose Washer in place onto

Hand Shower handle and place Hand Shower into Rototoble Holder.

£ae`

HesE OuTiET

FA(ING DOWN

lf Hand Showei does not fit well into Holder slot, check to moke sure that

wider side of Holder's Slot opening is on TOP (Fig. 5). If Holder is upside down,

rotate it 1800 into correct position. If it is too fl.ght to rotate, loosen the Philips strew

on the inner Slot wall, then rotate Holder into (orTetr position and rchghten s(rew.

If Hand Shower does not stay UP and falls down be{ause Holder rotates freely,

fightenthePhilipss(rewontheinnerSlotwoll.Ifitdoesnotfightenqnyfuther,

call Customer (ore to get free reploconent sent to you within 24 hours.

FA[lHG YOU

WIDER SLOT OPENING UP

i(REW

ROIATABL[

HOLDER

Right-hand

Side View

lMPORTANT: Hand tighten tonnedions ONLY. D0 NOT use wrench or pliers.

D0 NOT overrighten - this may cause woshor to bend and be pushed into shower arm. Use plumber's tape ONLY if needed

on shower arm thread if washers foil to stop lenkoge. D0 NOT use plumber's tape on any other connect.ons.

NOTE:Ifyoiirshowerormhasflbqllontheendinsteodofothreod,thisoldtypeofshowerormwillnotworkwiththis

and most other showers on the market toddy. Your existl.ng shower arm con be easily replaced with a stondord

1/2"threodshowerormovoiloblcotmostplumbingsupplystores.

Summary of content (2 pages)

PAGE 1
4-A;#® 3 way Show `ZPz To (onnec' 1. Remove old shower head. Strew Lock Nut, with single Inner Thread fo(,#y;A>©` YOU, onto showei arm to end of its thieod, but D0 NOT tighten (Fig.I ). 2. S(Few Water Diverfer with Thick Washer in place onto Shower Arm stopping £ae` ot lost possible position when Hose Outlet is facing DOWN (Fig. 2). lNNER THREAD FA[lHG YOU 0 3. Countem.ghten Lock Nut in ieverse diredion, until it presses fl.ghfly ogoinst Diverter, thereby lo{king it in this posifl.on. 4.
PAGE 2
lf it oppeflrs that you ore missing Washer(s) To Use 3 way Water I)ivener or other port(s), or hove a defectwe port, To change water flow, turn D.iverfer Switch 90° with Knob pointing toll (ustomer (ore to get free in the shutoff direction (Fig. 6). Point Lever STRAIGHT to use Hand replocementsenttoyou Shower, DOWN to use Shower Head or UP to use (ombinotion of both. within 24 hours. \DIAL To Adiusl Angle of Hand Shower LIVER Rotate Holder in vein.col directions to set desired Hand Shower angle.