CHARISMA SHOWER/TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or any other details please refer to the support.BathAuthority.com web page. Please read these instructions carefully before installing.
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the package, by marking all the components on the “Detailed Diagram of Shower/Tub Door Components”. Examine boxes and packages for shipping damage. If the unit has been damaged, has a finishing defect, or has missing parts, please contact our customer support department within 5 business days of the delivery date.
Detailed Diagram of Shower/Tub Door Components 5 1 6 3 7 8 9 4 10 11 12 2 13 14 15 16 17 Packing List 01 02 03 04 05 06 07 08 09 Guide rail Threshold Glass door Handle Wall anchor Round head screw ST4.2×16 Round head screw ST4.2×25 Round head screw ST4.
Shower/Tub Door Installation 1. Measure your finished opening width. This distance is marked as “W”. See Fig. 1 for details. Fig. 1 2. The Guide rail (01) and the Threshold (02) have been precut for an opening width of 60”. If your finished opening width is less than 60”, you will need to cut the Guide rail and the Threshold to the size of “W”. You can use a chop saw if available or a hack saw. File down any burrs that occur to prevent scratches on the wall.
W W Fig. 3 3. If the Threshold (02) has been cut off, the pre-drilled hole may be shifted. In this case you will need to drill another hole. Drill the hole from the top, 1-1/2” away from the end of the Threshold. Drill through both layers of aluminum using Ø3/16” drill bit, and then enlarge the hole of the first layer with Ø5/16” drill bit. 1 1/2″ 1 See Fig. 4 for details. Ø 3/16” 2 3/4” Ø 5/16” 3 Fig. 4 Ver. 2, Rev.
4. Place the Threshold (02) in the desired position and parallel to the front edge of the Shower base or the Tub. Measure the distance from the front edge of the Threshold to the far corner of the wall. This distance is “X”. (you will need this distance for Step 6) Mark the drill holes through the predrilled holes at both ends of the Threshold. X See Fig. 5 for details. Fig. 5 5. Drill the holes in the Shower base or the Tub using Ø 1/8” drill bit.
Height of the Guide Rail Bracket for Shower door. 6. Place your Guide Rail Bracket (11) at a height of 69-1/4” from the base and at dimension “X” from the back wall (from Step 4). Even front bottom corner of the Guide Rail Bracket with the outside of the Threshold (02) to mark the wall for drilling. Be sure to keep the Guide Rail Bracket level. X X 69 1/4” See Fig. 7 for details. Fig. 7 Height of the Guide Rail Bracket for Tub door. 7.
. Mark the drill holes on the wall using the Guide rail bracket (11). Drill the holes using Ø 5/16” drill bit, insert the Wall anchors (05) and secure the Guide rail bracket to the wall with the Round head screw ST4.2×35 (08). See Fig. 9 for details. 1 4 2 5 3 Ø5/16" Fig. 9 9. Repeat Step 6 / Step 7 and Step 8 to mount the second Guide rail bracket (11) to the opposite wall. 1 4 2 5 See Fig. 10 for details.
10. Bring the Guide rail (01) over the top of the Guide rail brackets (11) and lock them together. Mark the drill holes in the Guide rail through the hole in the middle of the bracket. Remove the Guide rail and drill the holes using Ø 1/8” drill bit. Slide the Roller assemblies (10) into the channel of the Guide rail. (Two rollers in each slot).
11. Secure the Glass doors (03) onto the Roller assemblies (10) and fasten them with the provided bolts. Attach the Handle brackets (12) onto the Glass doors. Attach Handles (04) to the Handle brackets. 1 4 2 5 3 6 See Fig. 13 and Fig. 14 for details. Fig. 13 NOTICE: On the outside Glass door, the Handle must be installed outwards. On the inside Glass door, the Handle must be installed inwards. Fig. 14 Ver. 2, Rev.
12. Slide the Glass doors (03) to the right side and secure the Left Guide block (13) to the left end of the Threshold (02). Drill the holes into the Threshold through predrilled holes in the Guide block and fasten the Guide Block with the Round head screw ST4.2×16 (06). Slide the Middle Guide block (13) off the left edge of the Glass doors and secure it to the center of the Threshold. Drill the holes into the Threshold using Ø 1/8” drill bit and fasten the Guide block to it using Round head screw ST4.
Caulk Fig. 17 Product Maintenance To ensure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. To ensure long lasting life for your glass shower products, wipe them off after each use with a soft cloth.
DREAMLINE LIMITED WARRANTY Bath Authority LLC’s (“DreamLine”) exclusive written warranty effective April 2, 2012 This warranty extends only to the original owner/end-user for household use only and is not transferable to a subsequent owner. This warranty applies only to DreamLine™ products purchased from an authorized dealer and installed in United States or Canada. Proof of purchase (original sales receipt) must be provided with all warranty claims.
DreamLine™ is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is excluded from this warranty. DreamLine™ reserves the right to modify this warranty at any time - such warranty modification will not alter warranty applicable at the time of sale of the products in question.
TEL: 866-731-8378 – 215-957-1411 FAX: 866-227-9245 – 215-893-1780 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors & Tub Doors please visit www.BathAuthority.com Ver. 2, Rev.
