AQUA FOLD SHOWER / TUB DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLine® reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings, manuals or additional details please refer to your model’s web page on DreamLine.com Model# SHDR-3634720-01 Model# SHDR-3636580-01 Left hand installation shown Please read these instructions carefully before installing.
Preparation 1. Prior to installation, examine all boxes and packages for shipping damage and compare the piece count with your packing slip. After opening all boxes and packages read this introduction carefully. Check that all of the needed parts are included in the package by checking off the components on the “Detailed Diagram of Shower Door Components”.
Tools Required Waterproof Silicone Tape Measure Level “AQUA FOLD” Ver.2 Rev.
Detailed Diagrams of Shower Door Components Packing List 01 02 03 04 05 06 07 Wall profile Glass door 1 (assembled) Glass door 2 Hinge (with allen wrench) Wall anchor Big head screw ST4.2×40 Round head screw ST4.
Shower Door Installation NOTE: This model is reversible for left or right hand installation. Left hand installation is demonstrated in this manual. For right hand installation, reverse the orientation of your product. 1. Prepare Glass door 1 (02) and Glass door 2 (03) to set the Hinges (04). See Fig. 1 for details. IMPORTANT! There is a top and a bottom to the assembled glass door rail. Top Fig. 1 2. First, attach the Hinges (04) to Glass door 1 (02), then attach Glass door 2 (03).
Fig. 3 3. Place the Wall profile (01) on the tub against the finished wall. Adjust the Wall profile (01) vertically using a level. See Fig. 4 for details. Fig. 4 “AQUA FOLD” Ver.2 Rev.
4. Mark the drill holes on the wall through the predrilled holes in the Wall profile (01). Now drill holes in the wall using a Ø5/16 drill bit and insert the Wall anchors (05). Apply silicone along the Wall profile (01) and around the holes. Fasten the Wall profile (01) to the wall with the Big head Screw ST4.2×40 (06). See Fig. 5 for details. 1 4 2 5 Ø5/16” 3 Fig. 5 5. Slide the assembled Glass doors with Hinged glass profile (02) into the groove of the Wall profile (01) and level it vertically.
6. Snap the Aluminum threshold (10) into the Threshold connector (09) and Threshold end cover (13). (Left hand installation shown) Run a bead of Waterproof silicone along the Aluminum threshold (10). Attach the Aluminum threshold (10) onto the tub parallel to the tub edge with the Threshold connector (09) tight to the bottom of the Hinged glass profile (02). See Fig 4.4. Run a bead of Waterproof silicone along the connections of the Threshold connector (09) and Hinged glass profile (02).
8. Mount the Handle Knob (14) onto Glass door 2 (03). 1 WARNING: The handle knob is metal. When folding the doors, please use caution to prevent the knob from contacting the glass to prevent damage. See Fig. 9 for details. 2 Fig. 9 9. Test the operation of the doors and adjust the hinge screws if necessary to make the door operate smoothly. See Fig. 10 for details. Fig. 10 “AQUA FOLD” Ver.2 Rev.
Product Maintenance BASES and BACKWALLS: To ensure long lasting life for your acrylic back walls: wipe them off after each use with a soft cloth. To clean the acrylic back walls use non-abrasive sprays or cream based cleaners. Never use abrasive cleansers, metal brushes or scrapers that could scratch or dull the surface. GLASS: To ensure long lasting life for your glass shower products: wipe them off after each use with a soft cloth.
TEL: 866-731-2244 FAX: 866-857-3638 DREAMLINE.COM For more information on DreamLine® Shower Doors and Enclosures please visit DreamLine.com “AQUA FOLD” Ver.2 Rev.
