User's Manual DM7020S Digital satellite receiver for free and encrypted DVB-TV Program, optional digital hard disk recording.
1. Contents 1. 2. 3. 3.1. 3.2. 3.3. 3.4. 3.5. 3.6. 3.7. 4. 4.1. 4.2. 4.3. 4.4. 4.5. 4.6. 4.7. 4.8. 4.9. 4.10. 4.11. 4.12. 4.13. 4.14. 4.15. 4.16. 4.17. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 14.1. 14.2. 14.3. 14.4. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 29.1. 29.2. Contents ................................................................................................................................ -2Views ................................................................................
0. 31. 32. 32. 32.1. 32.2. 32.3. 33. 34. 35. 35.1. 35.2. 35.3. 35.4. 35.5. 35.6. 36. 37. 38. 38.1. 39. 40. 41. 42. 43. 43.1. 43.2. 43.3. 43.4. 43.5. 43.6. 44. 45. 46. 47. 47.1. Services locking / unlocking ................................................................................................ - 29 A/V Settings ................................................................................................................................ - 30 UHF-Modulator..........................................
2.
3. Description Frontview 3.1. CI-Slot Plug in here any CI- Module of your choice. 3.2. Compact Flash Slot The Compact Flash Slot is meant to hold a Compact Flash Module. If you want to use a CF-Module, shut down your Dreambox by using the Deep-Standby-Mode. Plug in carefully your CF-Module into the Compact Flash Slot. The CF-Module is recognized by the System as a hard disk. To access the Compact Flash Module, choose the File-Mode in the OSD-Main menu.
4. Description Rear view 4.1. Main power 230V / 50Hz Plug in the power cable into the main power socket. The power plug remains only in its designated socket 230V / 50Hz. 4.2. TV Scart Connect your TV with an appropriate Scartcable to your Dreambox. 4.3. VCR Scart Connect your VCR with an appropriate Scartcable to your Dreambox. Remember, the VCR Scart is not designed to record a Video signal from the VCR. 4.4.
4.13. Mains Switch With the main switch you off your Dreambox completely. 4.14. Video Out (FBAS) You can optionally connect a TV to this connector. (Composite) 4.15. Modem Via the Modem Socket you can optionally connect to your ISP via a phone line. 4.16. 0 / 12V Out A 0 / 12V Relais to switch between Satellites can be connected here. 4.17. UHF Modulator Optionally connect your Dreambox to your TV via a coaxial cable.
5. Safety instructions Please read the safety instructions completely and carefully, before using the Dreambox. The Manufacturer takes no responsibility for incorrect handling of the Dreambox. - Allow enough space around the Dreambox for sufficient ventilation. - Do not cover the Dreambox’s ventilation openings with items such as newspapers, tablecloths, curtains etc. - Do not expose the Dreambox to dripping or splashing liquids.
6. Scope Of Supply The box of your DM7020S shall contain the following items: 1 receiver Dreambox 7020S 1 power cord 1 remote control 1 userís manual (latest release @ http://www.dream-multimedia-tv.de ) 2 batteries (1,5V Mignon / AA / LR6) 2 hard disk mounting racks (are premounted) 1 IDE cable 1 molex power cord for the hard disk optional parts: 1 wireless keyboard 7. Installation - Insert 2 AA (1,5V) batteries, taking care to observe the + and - markings indicated inside, into the Remote Control.
8.
9. Important Notes about Condition All functions of the Dreambox can be observed via OSD-Menu (On-Screen-Display). This makes the handling of the Dreambox very easy for you. All options are indicated by four colored dots or beams (red, green, yellow, blue) in the OSD-Menu and can be started with the Option-Buttons on the Remote Control. Depending on the chosen Menu, the Options do change and are explained via the Help-Button on the Remote Control.
10. Remote Control Description SHIFT-Setup-Button This Button is used to program the Remote Control for a TV Device. See Passage Setup-TV-Mode POWER-Button This Button switches your Dreambox on or off. See passage Dreambox switching on / off. TV-Mode-Button This Button turns the Remote Control into TV-Mode. The TV-Mode-Button flashes shortly, if you press this or any other Button in this Mode. The Remote Control controls now your TV. DREAM-Mode-Button This Button turns the Remote Control into Dream-Mode.
INFO-Button This Button shows the EPG Information’s. Pressing this Button twice shows the Stream information. OK-Button This Button shows the Infobar if no OSD-Menu is shown. This button enters a chosen OSD-Menu Option or Function. MENU-Button This Button shows the OSD-Main menu. If a Service list is opened, press this Button to enter the Service-Menu. AUDIO-Button The AUDIO-Button shows the available Audio-Tracks of the selected Service. VIDEO-Button This Button activates or deactivates the PVR-Mode.
11. Dreambox switching on / off Use the Power-Button to switch the Dreambox on or off. The Dreambox has two different StandbyModes. A Standby-Mode and a Deep-Standby-Mode. Unplug the Mains power cord to make the Dreambox completely powerless. The Power-Button only works if no OSD-Menu is shown on the TV screen! Press the Power-Button once to switch the Dreambox into Standby-Mode. The actual Time appears on the LC-Display.
13. OSD-Mainmenu If no OSD-Menu is shown on the TV screen, the MENU-Button enters the OSD-Mainmeu. Through this OSD-Mainmenu it is possible to activate the main options and functions. Use either the Navigation-Buttons followed by the OK-Button or press the desired number to enter the Option or Function. To change the view of the OSD-Mainmenu go to (6) Setup -> (3) System Settings -> (4) OSD Settings and check the checkbox "Show Mainmenu like Listbox ". Exit all menus and reenter the OSD-Mainmenu.
14. Infobar The Infobar appears and disappears by pressing the OK-Button once, if no OSD-Menu is shown on your TV screen. The Infobar shows all necessary Information about the selected Service. "Crypted” appears orange, if the transmitted Service is crypted. "Aspect Ratio” appears orange, if the Service is transmitted in 16:9, the usual Aspect Ratio is 4:3. "Dolby Digital Program” appears orange, if the Service is transmitted with Dolby Digital Audio stream.
14.1. Infobar - EPG (Electronic Program Guide) The red dot in the Infobar appears if the selected program transmits EPG information’s. Press the red Option-Button to enter the EPG. Press the OK-Button to view detailed Information. Press the EXIT-Button to exit this menu. 14.2. Infobar - Subservices The green dot in the Infobar appears if the selected program provides Subservices. Press the green Option-Button to enter the menu multiple services".
14.3. Infobar - Audio Track The yellow dot in the Infobar appears if the selected Service transmittes multiple Audio-Tracks. Use the Navigation-Buttons left or right to choose the different Audio-Modes, Left-Mono, Stereo, RightMono. Press the OK-Button to activate. Use the Navigation-Buttons up or down to choose another Audio-Language. Press the OK-Button to activate. 14.4. Infobar - Plugins The blue dot in the Infobar appears permanently Use the Navigation-Buttons up or down to choose a Plugin.
15. Setup - OSD Language Press the MENU-Button to enter the OSD-Main menu. Go to (6) Setup -> (3) System Settings -> (5) OSD Language. Use the Navigation-Buttons up or down to choose your language. Press the OK-Button to activate. Exit all menus and reenter. 16. Setup - Time Zone Press the MENU-Button to enter the OSD-Main menu. Go to (6) Setup -> (3) System Settings -> (1) Time Settings -> (1) Timezone Configuration. Press the OK-Button to open the Dropdown list.
18. Satellite Configuration Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (2) Service Searching -> (1) Satellite Configuration. Navigate to the upper Dropdown list and choose your appropriate Satellite Configuration and press the OKButton. Choose your Satellites the Dish is adjusted to and press the green Option-Button to save configuration. This Configuration might differ from yours. 19. Satfind Press the MENU-Button. Go to (6) Setup -> (2) Service Searching -> (2) Satfind.
20. Motor Setup Press the MENU-Button to enter the OSD-Main menu. Go to (6) Setup -> (2) Service Searching -> (3) Motor Setup. Before proceeding with the Motor Setup refer to passage Satellite Configuration and choose from the upper Dropdown list "many satellites via DiSEqC Rotor" and press the OK-Button, if you setup a Motor for the first time. All possible satellites will be listed. Press the green Option-Button to save this configuration.
21. Automatic Transponder Scan Press the MENU-Button to enter the OSD-Main menu. Go to (6) Setup -> (2) Service Searching -> (5) Automatic Transponder Scan. The Automatic Transponder Scan scans one satellite after one which is configured. Select the first satellite to scan and press the OKButton. Now choose to scan only Free services or not by setting a check or not. If your LNB is not a C-Band LNB, then let the check in the Checkbox in front of no circ polariz.
22. Automatic Multisat Scan Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (2) Service Searching -> (6) Automatic Multi Scan. The Automatic Multisat Scan is recommened for scanning all configured satellites at once. By pressing the OK-Button on each satellite a couple of times, you set the scan method.
. Transponder Edit Press the MENU-Button to enter the OSD-Main menu. Go to (6) Setup -> (2) Service Searching -> (4) Transponder Edit. This Menu keeps all known satellites the Dreambox scans for. If you recognize a missing satellite, add or edit the satellite. Pressing the OK-Button on the sat-button, enters the Satellite Edit Menu. Pressing the OK-Button on the add-button, adds a new frequency to the selected satellite.
. Service Organising - Create new Bouquet The Bouquets are used to save your favorite services from the Main Service list into one simple bouquet. You can ether add a TV, Radio or a File Bouquet. In this example we only describe creating a TV Bouquet, because it’s always the same procedure. Press the MENU-Button to enter the OSD-Main menu. Go to (6) Setup -> (1) Service Organising -> (1) Create new Bouquet. This Menu shows the Bouquet Types, the Dreambox allows you to add.
. Service Organising - Add services to Bouquet Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (1) Service Organising -> (2) Add services to Bouquet. This Menu shows the Bouquet Types, the Dreambox allows you to add services to. Select TV and press the OK-Button. This Menu shows the System default Bouquets, Servicenumbers and Favorites (TV). The Bouquet "my own bouquet" has been created one passage before. Navigate to the created Bouquet and press the OKButton.
. Service Organsing - Edit Bouquets Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (1) Service Organising -> (3) Edit bouquets. In this Menu you can only rename the selected Bouquet Type by pressing the yellow Option-Button. Choose a Bouquet Type you wish to edit a Bouquet from. In our example we do choose Bouquets (TV) to edit. Press the OK-Button. Press the red Option-Button to delete a selected Bouquet.
29. Parental Lock Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (5) Parental Lock. Parental lock is used to lock services of your choice inside the Service list against access. Setup lock is used to lock the Menu (6) Setup against access. The Parental setup requires a four digit code of your choice called PIN for Parental lock and Setup lock. Attention: Loosing this PIN requires a "Flash Erase" of the Operation system to reset to factory defaults.
30. Services locking / unlocking Press the TV-Button to bring up the Service list. Choose the Service you want to lock / unlock and press the MENU-Button. You can lock / unlock services in any Service list. Press the desired Option-Button to enter either All Services, Satellites , Providers or Bouquets After pressing the MENU-Button the Service Menu appears. Navigate to the option “lock” / “unlock” and press the OK-Button to lock / unlock the selected service.
31. A/V Settings Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (3) System Settings -> (2) A/V Settings. Use ether the Navigation-Buttons left and right or the OKButton to change or set the Values. Color Format: CVBS(FBAS), RGB (Red, Green, Blue seperated), SVideo (Color- and Brightness signal seperated) and YPbPr (Component signal e.g. for Projectors).
32. UHF Modulator Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (3) System Settings -> (3) UHF Modulator. Connect your TV set with an appropriate Coax cable to the UHF-Output of your Dreambox. Start the scan on your TV set. The UHF Modulator is set to channel 36 by default. If your VCR has the same channel, you can change this value. If you want, you can change these values with the Navigation-Buttons and the OK-Button. Save your Settings with the green Options-Button.
. OSD Settings Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (3) System Settings -> (4) OSD Settings. Use the Navigation-Buttons left or right to decrease or increase the selected slider. Alpha: Setup how much the TV picture should be visable through the OSD. Brightness: Setup the Brightness of the OSD. Contrast: Setup the Contrast of the OSD. Show Mainmenu like Listbox: Set a check into Checkbox to enable listboxview of the OSD-Mainmenu. Change skin: Setup a new skin.
32.2.
32.3. TuxText position Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (3) System Settings -> (4) OSD Settings, press the yellow Option-Button (TuxText position). This Menu is used to adjust the Position of the TuxText. Maybe the Clock does not appear or the Text pages are not shown in the middle of the screen. Press the HELP-Button for more information. The red Option-Button enables the Top left Point of the rectangle.
TuxText viewing options: Press the Volume-Mute-Button a couple of times to switch to alpha-mode, invisible-mode and full mode. The alpha-mode shows the picture from the running program through the Text pages. The invisible-mode shows the complete picture from the running program without exiting the TuxText. The full-mode brings back the Textpage. Press the Volume + Button to toggle between double high from the upper half, double high from the lower half and full view Text page.
34. LCD Settings Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (3) Sytem Settings -> (6) LCD Settings. The LC-Display Setup is used to adjust the Brightness of the LCD at your Dreambox. Use the NavigationButtons left or right to adjust the Brightness, Contrast and Standby. Standby is used to adjust the Brightness in StandbyMode. All adjustments take effect immediately. Checking the Checkbox “Inverted", inverts the LCD. Press the green Option-Button to save. 35.
35.1. Communication (Network, LAN Setup) Press the MENU-Button to enter the OSD-Main menu. Go to (6) Setup -> (6) Expert Setup -> select Communication Setup. Use the Navigation-Buttons and the NumericKeyboard to set the Values. IP: Enter the IP-Address here. The IP-Address is used to specify the Host IP-Address. Netmask: Enter the Netmask here. The Netmask is used to find an Host IP-Address in its Subnet. Type: LAN (Local Area Network); Connection to the home Network. Default is LAN.
35.2. Communication (Network, WAN (DSL) Setup) Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (6) Expert Setup -> (1) Communication Setup. Navigate to Type, press the OK-Button and select WAN(PPoE). Use this Type of Connection only, if the Dreambox is connected directly to a DSL Modem. T-DSL is used to enter the Account information only for German T-Com users. Login: Enter the Loginname provided from your ISP (Internet Service Provider).
35.4. Software Update over Internet Press the MENU-Button to enter the OSD-Main menu. Go to (6) Setup -> (6) Expert Setup -> (3) Software Update -> select Internet Update. The Internet Update function only works, if you have configured the Network, and the Dreambox is connected to ether a Router or a DSL-Modem. This window shows the currently installed Software. The latest release is always on top of this list.
36. Hard Disk - Assembly Instructions Unplug any cable from the Dreambox. Do not touch any Parts on the PCB. Please take care about ESD. Make sure you are shielded before opening or touching the device. Do not open the Dreambox in your living room on the carpet or any other electrostatic loaded floors. Open the Dreambox only with the described tools. If this all does not say anything to you, please consult your local dealer for assistance. Before opening the device read the Safety Instructions.
Part-List 1 Dreambox (includes Top cover, Screws (left, right, rear)) 1 Philips-Screwdriver 1 Hard Disk 1 IDE-Cable 1 Molex-Power-Cable 2 Mounting racks (build in by default) 4 Hard Disk Screws of your choice Unscrew the screws from the rear using the screwdriver. Unscrew the two screws from the right side. Unscrew the two screws from the left side.
Remove the cover. Remove the hard disk mounting bay by unscrewing the 2 highlighted screws.
Now you can see the IDE-Connector (white or black 40 Pin connector) and the PowerConnector (4 Pin connector). Fold the cable as shown.
Fold the cable again as shown above. Now you need the hard disk, the screwdriver and the mounting bay.
Mount the hard disk on the mounting bay. Set the Hard Disk Jumper to "Master“. Refer to the Hard Disk manual how to set these jumpers.
Connect the power connector and the data cable. Then screw the 2 screws back in. Remount the cover. Be careful not to break these plastic-clips.
37. Hard Disk Setup Press the MENU-Button to enter the OSD-Mainmenu. Go to (6) Setup -> (3) System Settings -> (3) Harddisc Setup -> select the Harddisc. This Menu shows the major Information about the installed Harddisc. Before formatting the Harddisc, please select from the right arrow dropdown menu a filesystem which the Harddisc will be formatted with. Choose an "ext3" file system pressing the OK-Button. Press the red Option-Button to format. Press the yellow Option-Button to check the File system.
38.1. Viewing/deleting/renaming recorded movies Press the MENU-Button to enter the OSD-Main menu. Go to (3) File Mode. You can also enter the File-Mode using the Navigation-Buttons up or down without entering the OSDMain menu, to bring up the Service list. Press the TEXT-Button to enter the recorded movies list. Watching: Select a movie by pressing the OK-Button. The Playback starts. Remember always to activate the PVR-Mode before controlling a recording or play of a service by pressing the VIDEO-Button.
39. Recording a movie (Timer recording) Attention: Timer recording is working in Standby-Mode and in Deep-Standby-Mode. Open a Service list using the Navigation-Buttons up or down or pressing the TV-Button. Select a service you want to program into the Timer. Watch this service for a couple of seconds until the red EPG dot in the Infobar appears. Remember, not every service provides EPG Information’s. Press the red OptionButton. Choose an event and press the green Option-Button to add it to the Timer.
40. Timeshift Activate the PVR-Mode by pressing the VIDEO-Button. Record at least a service for 1 minute. Now you can rewind, pause and forward the movie during record. This is a useful function, maybe the phone is ringing and you don’t want to miss the running program. 41. Timer Press the MENU-Button to enter the OSD-Main menu. Go to (9) Timer. The Timer list keeps all programmed Timerevents. This could be a Sleeptimer or a Timerevent for recording or switching to a service.
42. Information - Streaminfo / About Press the MENU-Button to enter the OSD-Main menu. Go to (4) Information. Press the OK-Button to enter the Streaminfo. Use the Navigation-Button right to open the following windows. Use the Navigation-Button left to go back. Navigate to “About” and press the OK-Button to enter. Press the EXIT-Button to exit. This window shows detailed Information about the chosen Service. This window shows Information about supported and used coding systems.
43. DreamUp - Software upgrade !!!! Very important, please read this passage completely, before starting upgrading !!!! DreamUp and the Images (Software) for the DM7020S are available at our Website www.dm7020.de. Remove all cables from the Dreambox. Connect only the serial and the Patchcable. The Mainspowercord is disconnected. You need a Windows PC with a serial port (COM1 or COM2) and an Ethernet card. Connect the Ethernet card with the Dreambox Communication port using a Crossover Patchcable.
43.1. DreamUp - Preparing DreamUp Start the Software DreamUp for DM7020 on your PC. Choose the COM Port, which is connected to the Dreambox. Make sure the Checkbox "Use Network" is checked. If not, the Software connects only serial. Type in the IP-Address from your PC "Local IP (PC)". Type in an IP-Address "Remote IP (Box)" for the Dreambox, e.g. 10.0.0.97.
43.2. DreamUp - Establish a Connection Click on the Connect-Button. Dreamup tells you, that the Connection is prepared Plug in NOW the Mainspowercord into the Dreambox.
After DreamUp has connected to the Dreambox, the other Buttons appear in black letters. You can now use them. Click on the Ping-Button to test the Ethernet Connection. You will notice the Ping result in the Log window. If not, please check your Network configuration.
43.3. DreamUp - Backup Software Clicking on the Backup-Button saves the complete installed Software with all your settings. The file window opens. Type in any name of your choice plus the extension .img or .bin.
After clicking on the Save-Button the Software will be downloaded from your Dreambox. Watch the Progress bar and Status. You get a message from DreamUp after downloading has been finished. With result 0, everything is ok. Click on the OK-Button to quit.
43.4. DreamUp - Erasing Software Click on the Erase-Button to erase the currently installed Software. This is sometimes, but not always necessary. You will get a security question from DreamUp, if you are sure. Click the Yes-Button.
Watch the Progress bar and Status. After erasing the Software, DreamUp tells you that everything is ok with a flash erase result 0. Click on the OK-Button to quit.
43.5. DreamUp - Flashing Software Click on the Flash-Button to select an Image file (Software). Choose an image file and click on the Open-Button.
After clicking on the Open-Button, the image will be immediately uploaded to the Dreambox. Watch the Progress bar, the Status and Log window. After the upload is completed the flash will be erased. Watch the Status and Log window.
The image will be verified after flashing. The flash procedure is completed, if you get a Flash update finished result 0. Click on the OK-Button to quit.
43.6. Dreambox resetting to factory defaults (flash erase) Your Dreambox is now flashed with a new image (Software). Click on the Exit-Button to close DreamUp. Disconnect the Mainspowercord from the Dreambox. Wait at least 30 seconds. Plug in the Coax cable first, then the Scartcable and all other cables. Turn on the TV and set it to AV Plug in NOW the Mainspowercord. As soon as you see the Dream-Logo on the TV-Screen, press the Channel-Up-Button at the Front of the Dreambox.
45.
Output analog: Output Level L/R 0,5 Vss on 600 Ohm THD > 60 dB (1 kHz) Crosstalk < -65 dB Output digital: Output Level 0,5 Vss on 75 Ohm Sampled Data Filtering 32 kHz, 44.1 kHz, 48 kHz S/PDIF-Output optical (AC3) Video parameter: Input Level FBAS 1 Vss +/- 0.3 dB on 75 Ohm Teletext filter in conformity with ETS 300 472 Standard TV-Scart: Output: FBAS,RGB,S-VHS over OSD selectable VCR-Scart: Input: FBAS,RGB,S-VHS Output: FBAS Serial Interface RS 232: Typ RS232 bidirectional Bitrate 115,2 kBit/s max.
Physical specification: Ambient Temperature +15°C...+35°C Humidity < 80% Size (W x D x H): 374 mm x 230 mm x 75 mm Weight: 2 kg without HDD 46. Contact & Support Information Headquarter & Distribution: Dream-Multimedia Dealer Hotline: (only Dealer) Tel: 0180 - 3 68 43 98 - 000 Fax: 0180 - 3 68 43 98 - 001 Mo - Fr. 10:00 am - 05:00 pm Technical Hotline: Tel: 0180 - 3 68 43 99 - 777 Fax: 0180 - 3 68 43 99 - 778 Mo - Fr.
47. Setup-TV-Mode Choose a code from the TV - Codelist for your TV in German Manual and follow this procedure to program the Remote Control for your TV. TV-Mode-Button SHIFT-Setup-Button 4-digit-code SHIFT-Setup-Button TV-Mode-Button Numeric-Keyboard 47.1. Program sequence - Press the TV-Mode-Button. - Press the SHIFT-Setup-Button for at least 2 seconds, the TV-Mode-Button blinks two times. - Enter each digit step by step. The TV-Mode-Button blinks after each digit.
