VigorAP 1060C 11ax Ceiling AP Quick Start Guide Version: 1.0 Firmware Version: V1.3.
Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp.
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type VigorAP 1060C is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.draytek.com.tw/ftp/VigorAP 1060C/Document/CE/ Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu County, Taiwan 303 Product: VigorAP 1060C Frequency Information for Europe area: 2.
USA Local Representative Company name ABP International Inc. Address 13988 Diplomat Drive Suite 180 Dallas TX 75234 ZIP Code 75234 E-mail rmesser@abptech.com Contact Person Mr. Robert Messer Tel. 19728311600 Caution Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.
Table of Contents 1. Package Content .................................................................................................. 1 2. Panel Explanation ................................................................................................. 2 3. Installation ............................................................................................................. 3 3.1 Ceiling-mount Installation (Wooden Ceiling) .............................................................................
1. Package Content Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. VigorAP 1060C Main Unit Quick Start Guide 15/16" and 9/16" Mount Base (for ceiling mounting) Fixings and Screws (for ceiling mounting) Mount Base (for wall mounting) Screw Set (for wall / ceiling mounting) Cable Tie RJ-45 Cable (Ethernet) Note Power Input: 12V 2.5A PoE Input: 54V 0.
2. Panel Explanation Factory Reset Ethernet Port Power Jack (DC IN) LED Security Hole LED 1 2 Status On (Blue) Off Blinking(Blue) Off Blinking(Blue) Interface Ethernet Port Power Jack(12V Hole Factory Reset Security Hole Note Explanation The system is in boot-loader mode. The system is not ready or fails. The system is in TFTP mode. The system is not ready or fails. The system is ready and can work normally. Explanation Connects to LAN or router. Supports PoE power & Gigabit (2.5Gpbs). 2.
3. Installation VigorAP can be installed under certain locations: wooden ceiling, plasterboard ceilings, light-weighted steel frame and wall. 3.1 Ceiling-mount Installation (Wooden Ceiling) Determine where the Access Point to be placed and mark location on the surface for the two mounting holes. Use the appropriate drill bit to drill two holes in the markings and hammer the bolts into the openings. 1. Place the mount base under the wooden ceiling and fasten it on the ceiling with two screws firmly. 2.
3.2 Ceiling-mount Installation (Plasterboard Ceiling) 1. Place the Mount Base under the plasterboard ceiling and fasten two turnbuckles firmly. 2. Make the screws pass through the Mount Base and insert into the turnbuckles. Fasten them to offer more powerful supporting force. 3. When the Mount Base is in place, slide the mount base into the slot of the AP.
3.3 Suspended Ceiling (Lightweight Steel Frame) Installation You cannot screw into ceiling tiles as they are weak and not suitable for bearing loads. Your VigorAP is supplied with mounts (Mount Base) which will be used to attach directly to the ceiling frame of your suspended ceiling. 1. Slide the mount base into the slot of the AP. 2. Hold the Access Point with one hand to reach the other hand over the T-Rail sides of the bracket. 3.
3.4 Wall-Mounted Installation For wall-mounting, the VigorAP has keyhole type mounting slots on the underside. 1. Use the appropriate drill bit to drill two 8.1mm diagram and 26mm depth holes in the markings and hammer the bolts into the openings. 2. Screw the anchors unto the holes until they are flush with the wall; screw the included screws into the anchors. 3. Place the Access Point against wall with the mounting screw heads.
4. Connection and Configuration 4.1 Connect to a Vigor Router using AP Management Your VigorAP can be used with Vigor routers which support AP management (such as the Vigor2865 or Vigor2927 series). AP Management enables you to monitor and manage multiple DrayTek APs from a single interface. 1. Connect VigorAP to PoE switch (via LAN port) with Ethernet cable. VigorAP will get the power from the switch directly. Then, connect the VigorSwitch to a Vigor router. 2.
4.2 Web Configurations This section will guide you to install the AP and make configuration for VigorAP. Connected As a Mesh Node (in Mesh Network) Install VigorAP on to the ceiling. As a mesh node, settings related to VigorAP 1060C must be configured by a remote Mesh Root (e.g., VigorAP 903) within the mesh network. The user must detect VigorAP 1060C via a Mesh Root to add it as a mesh node.
There are two methods to configure VigorAP. Method 1: (a) First, open a web browser on your PC and type https://192.168.1.2. A pop-up window will open to ask for username and password. Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be in the same subnet as the IP address of VigorAP 1060C. If there is no DHCP server on the network, then VigorAP 1060C will have an IP address of 192.168.1.2.
(c) Follow the on-screen steps to finish the network connection. Method 2: (a) Use a mobile phone to scan the QR code named with DrayTek Wireless App to download DrayTek Wireless APP. (b) After downloading, run the APP. (c) Click Quick Start Wizard. Next, scan the QR code named with Connect SSID. Later, click Connect to access into the APP user interface of VigorAP 1060C to set the device in AP or Range Extender mode.
5. Customer Service If the device cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to “support@draytek.com”. Be a Registered Owner Web registration is preferred. You can register your Vigor router via http://www.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded.
