User`s guide
Table Of Contents
- Table of Contents
- 1. Preface
- 2. Initial Configuration
- 3. Advanced Configuration
- 4. Application and Examples
- 4.1 How to Configure Multi-Subnet in Vigor2830
- 4.2 How Can I Use FTP to Get the Files from USB Storage DeviceConnecting to Vigor Router?
- 4.3 How to Send out SMS via Vigor Router
- 4.4 Web Portal Log-In Application for Wireless Client
- 4.5 How to Customize Your Login Page
- 4.6 Create a LAN-to-LAN Connection Between Remote Officeand Headquarter
- 4.7 Create a Remote Dial-in User Connection Between theTeleworker and Headquarter
- 4.8 QoS Setting Example
- 4.9 Upgrade Firmware for Your Router
- 4.10 Request a certificate from a CA server on Windows CAServer
- 4.11 Request a CA Certificate and Set as Trusted on WindowsCA Server
- 4.12 Creating an Account for MyVigor
- 5. Trouble Shooting
- 5.1 Checking If the Hardware Status Is OK or Not
- 5.2 Checking If the Network Connection Settings on YourComputer Is OK or Not
- 5.3 Pinging the Router from Your Computer
- 5.4 Checking If the ISP Settings are OK or Not
- 5.5 Problems for 3G Network Connection
- 5.6 Backing to Factory Default Setting If Necessary
- 5.7 Contacting Your Dealer
Vigor2830 Series User’s Guide
210
3
3
.
.
1
1
2
2
.
.
1
1
D
D
i
i
a
a
l
l
P
P
l
l
a
a
n
n
This page allows you to set phone book and digit map for the VoIP function. Click the Phone
Book and Digit Map links on the page to access into next pages for dialplan settings.
Available settings are explained as follows:
Item Description
Enable Secure Phone
It allows users to have encrypted RTP stream with the peer
side using the same protocol (ZRTP+SRTP). Check this
box to have secure call.
Enable SAS Voice Prompt
If it is enabled, SAS prompt will be heard for both ends
every time. If it is disabled, no SAS prompt will be heard
any more.
A
A
p
p
p
p
l
l
i
i
c
c
a
a
t
t
i
i
o
o
n
n
f
f
o
o
r
r
S
S
e
e
c
c
u
u
r
r
e
e
P
P
h
h
o
o
n
n
e
e
Enable SAS Voice Prompt, for ex: if vigor router A calls vigor router B with checking Enable
Secure Phone and Enable SAS Voice Prompt, then:
1. After the connection established, vigor router A will send SAS voice prompt to A and
vigor router B will send the SAS voice prompt to B.
2. Then the RTP traffic is secured until the call ends.
3. If vigor router A wants to call vigor router B again next time, both A and B will not hear
any voice prompt again even checking Enable SAS Voice Prompt on web UI. It means
only the first call between them will have voice prompt.
Enable SAS Voice Prompt, for ex: if vigor router A calls vigor router B with checking Enable
Secure Phone but not Enable SAS Voice Prompt, then:
1. After the connection established, vigor router A will NOT send SAS voice prompt to
vigor router A and vigor router B will NOT send the SAS voice prompt to vigor router B.
2. Even no voice prompt, but the RTP traffic is still secured until the call ends.
Note: If the incoming or outgoing calls do not match any entry on the phonebook, the
router will try to make the call "being protected". But, if the call ends up "unprotected"(e.g.
peer side does not support ZRTP+SRTP), the router will not play out a warning message.