User`s guide
Table Of Contents
- Table of Contents
- 1. Preface
- 2. Initial Configuration
- 3. Advanced Configuration
- 4. Application and Examples
- 4.1 How to Configure Multi-Subnet in Vigor2830
- 4.2 How Can I Use FTP to Get the Files from USB Storage DeviceConnecting to Vigor Router?
- 4.3 How to Send out SMS via Vigor Router
- 4.4 Web Portal Log-In Application for Wireless Client
- 4.5 How to Customize Your Login Page
- 4.6 Create a LAN-to-LAN Connection Between Remote Officeand Headquarter
- 4.7 Create a Remote Dial-in User Connection Between theTeleworker and Headquarter
- 4.8 QoS Setting Example
- 4.9 Upgrade Firmware for Your Router
- 4.10 Request a certificate from a CA server on Windows CAServer
- 4.11 Request a CA Certificate and Set as Trusted on WindowsCA Server
- 4.12 Creating an Account for MyVigor
- 5. Trouble Shooting
- 5.1 Checking If the Hardware Status Is OK or Not
- 5.2 Checking If the Network Connection Settings on YourComputer Is OK or Not
- 5.3 Pinging the Router from Your Computer
- 5.4 Checking If the ISP Settings are OK or Not
- 5.5 Problems for 3G Network Connection
- 5.6 Backing to Factory Default Setting If Necessary
- 5.7 Contacting Your Dealer
Vigor2830 Series User’s Guide
193
Dial-Out Settings
Type of Server I am calling - PPTP - Build a PPTP VPN
connection to the server through the Internet. You should
set the identity like User Name and Password below for the
authentication of remote server.
IPSec Tunnel - Build an IPSec VPN connection to the
server through Internet.
L2TP with IPSec Policy - Build a L2TP VPN connection
through the Internet. You can select to use L2TP alone or
with IPSec. Select from below:
z None: Do not apply the IPSec policy. Accordingly,
the VPN connection employed the L2TP without
IPSec policy can be viewed as one pure L2TP
connection.
z Nice to Have: Apply the IPSec policy first, if it is
applicable during negotiation. Otherwise, the dial-out
VPN connection becomes one pure L2TP connection.
Must: Specify the IPSec policy to be definitely applied on
the L2TP connection.
User Name - This field is applicable when you select,
PPTP or L2TP with or without IPSec policy above. The
maximum length for username is 49 characters.
Password - This field is applicable when you select PPTP
or L2TP with or without IPSec policy above. The maximum
length for password is 15 characters.
PPP Authentication - This field is applicable when you
select, PPTP or L2TP with or without IPSec policy above.
PAP/CHAP is the most common selection due to wild
compatibility.
VJ compression - This field is applicable when you select
PPTP or L2TP with or without IPSec policy above. VJ
Compression is used for TCP/IP protocol header
compression. Normally set to Yes to improve bandwidth
utilization.
IKE Authentication Method - This group of fields is
applicable for IPSec Tunnels and L2TP with IPSec Policy.
z Pre-Shared Key - Input 1-63 characters as pre-shared
key.
z Digital Signature (X.509) - Click Digital Signature to
invoke this function and select one predefined Profiles
set in the VPN and Remote Access >>IPSec Peer
Identity as Peer ID.
Local ID – Specify which one will be inspected first.
z Alternative Subject Name First – The
alternative subject name (configured in
Certificate Management>>Local Certificate)
will be inspected first.
z Subject Name First – The subject name
(configured in Certificate
Management>>Local Certificate) will be
inspected first.