i Vigor 2710 Series Quick Start Guide
Vigor 2710 Series Quick Start Guide ii
Vigor2710 Series ADSL2/2+ Firewall Router Quick Start Guide Version: 3.0 Firmware Version: V3.6.
Copyright Information Copyright Declarations Copyright 2012 All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: z Microsoft is a registered trademark of Microsoft Corp.
European Community Declarations Manufacturer: Address: Product: DrayTek Corp. No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu, Taiwan 303 Vigor2710 Series Router DrayTek Corp. declares that Vigor2710 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE Directive 1999/5/EEC.
Vigor 2710 Series Quick Start Guide vi
Table of Contents 1. Introduction........................................................................................................... 1 1.1 Panel Explanation ...................................................................................................................... 2 1.1.1 For Vigor2710 ............................................................................................................... 2 1.1.2 For Vigor2710n .......................................................................
Vigor 2710 Series Quick Start Guide viii
1. Introduction The Vigor2710 series features advanced bandwidth control mechanism such as IP-layer QoS, NAT Session Limitation, Bandwidth Borrowed, etc., to allow easy, flexible, reliable access control and bandwidth management. The SPI (Stateful Packet Inspection) firewall uses object-based design to make settings of firewall policies easy.
1.1 Panel Explanation 1.1.1 For Vigor2710 LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. The profile(s) of CSM (Content Security Management) for IM/P2P, URL/Web Content Filter application can be enabled from Firewall >>General Setup. (Such profile must be established under CSM menu). The router is ready to access Internet through DSL link. Slowly: The modem is ready. Quickly: The connection is training. The port is connected.
Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch.
1.1.2 For Vigor2710n LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. Wireless access point is ready. It will blink while wireless traffic goes through. The router is ready to access Internet through DSL link. Slowly: The modem is ready. Quickly: The connection is training. The port is connected. The port is disconnected. The data is transmitting. A USB device is connected and active. The data is transmitting.
Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch.
1.1.3 For Vigor2710Vn LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. Wireless access point is ready. It will blink while wireless traffic goes through. The router is ready to access Internet through DSL link. Slowly: The modem is ready. Quickly: The connection is training. The port is connected. The port is disconnected. The data is transmitting. A USB device is connected and active. The data is transmitting.
Interface Description Line Phone2/Phone1 Connector for PSTN life line. Factory Reset PWR ON/OFF Connector of analog phone for VoIP communication. Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Connector for a power adapter. Power Switch.
1.1.4 For Vigor2710VDn LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. Wireless access point is ready. It will blink while wireless traffic goes through. The router is ready to access Internet through DSL link. Slowly: The modem is ready. Quickly: The connection is training. The port is connected. The port is disconnected. The data is transmitting. A USB device is connected and active. The data is transmitting.
Interface Description WLAN Press the button once to enable (WLAN LED on) or disable (WLAN LED off) wireless connection. DSL Connector for accessing the Internet through ADSL2/2+. Connectors for local networked devices. Connector for USB storage (Pen Driver/Mobile HD) or printer. LAN (1-4) USB Interface Description Line Phone Connector for PSTN life line. Factory Reset PWR ON/OFF Connector of analog phone for VoIP communication. Restore the default settings.
1.2 Package Content n Quick Start Guide o CD q Antenna (n models) r Stand p RJ-45 Cable (Ethernet) s The type of the cable depends on the country that the router will be installed: Or RJ-11 to RJ-11 Cable (Annex A) Or RJ-11 to RJ-45 Cable (Annex B) RJ-45 to RJ-45 Cable (Annex B) t The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 17-23 Watt.
2. Installing Your Router This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. 2.1 Hardware Installation Before starting to configure the router, you have to connect your devices correctly. 1. Connect the ADSL interface to the external ADSL splitter with an ADSL line cable for all models. For Vigor2710Vn/VDn, also connect Line interface to external ADSL splitter. 2.
(For the detailed information of LED status, please refer to section 1.1.) Caution: 1. Each of the Phone ports can be connected to an analog phone only. Do not connect the phone ports to the land line jack. Such connection might damage your router. 2. When the power is shutdown, VoIP phone will be disconnected. However, a phone set connected to Phone 2 port can be used as the traditional telephone for the line will be guided to land line jack via the router (loop through).
Stand Installation The Vigor2710 series must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation.
2.2 Printer Installation You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows XP/2000. For Windows 98/SE/Vista/7, please visit www.draytek.com. Before using it, please follow the steps below to configure settings for connected computers (or wireless clients). 1. Connect the printer with the router through USB port. 2. Open Start->Settings-> Printer and Faxes.
3. Open File->Add a New Computer. A welcome dialog will appear. Please click Next. 4. Click Local printer attached to this computer and click Next. 5. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port. Click Next.
6. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next. 7. Click Standard and choose Generic Network Card. 8. Then, in the following dialog, click Finish.
9. Now, your system will ask you to choose right name of the printer that you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next. 10. For the final stage, you need to go back to Control Panel-> Printers and edit the property of the new printer you have added. 11. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next please refer to the red rectangle for choosing the correct protocol and UPR name.
The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router. Note 1: Some printers with the fax/scanning or other additional functions are not supported. If you do not know whether your printer is supported or not, please visit www.draytek.com to find out the printer list. Open Support > FAQ/Application Notes; find out the link of Printer Server and click it; then click the What types of printers are compatible with Vigor router? link.
3. Configuring Web Pages To access Internet, please finish basic configuration after completing the hardware installation. 3.1 Accessing Web Page 1. Make sure your PC connects to the router correctly. Notice: You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1. For the detailed information, please refer to the later section - Trouble Shooting of the guide. 2.
3.2 Basic Configuration The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. 1. Open a web browser on your PC and type http://192.168.1.1. A pop-up window will open to ask for username and password. 2. Please type “admin/admin” as the Username/Password and click Login. 3. The Main Screen will appear. Click Quick Start Wizard.
5. On the next page as shown below, please select the appropriate Internet access type according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. Then click Next for next step. PPPoE/PPPoA: if you click PPPoE or PPPoA as the protocol, please manually enter the Username/Password provided by your ISP. Then click Next.
1483 Bridged IP /1483 Routed IP: if you choose 1483 Bridged IP / 1483 Routed IP as the protocol, you will get the following page. Please type in the IP address information originally provided by your ISP. Then click Next for next step. 6. Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary. Click Finish and then restart the router. Afterward, you will enjoy surfing on the Internet.
3.3 Wireless Configuration For the user of Vigor2710, please skip this section. For operating Vigor2710n/Vn/VDn well, it is necessary for you to set the wireless LAN settings for using wireless function. Please read the following paragraphs carefully for configuring the settings for this router. 3.3.1 Using WPS In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an Access Point (AP) connecting to lots of wireless clients or Stations (STA).
There are two methods to do network connection through WPS between AP and Stations: pressing the Start PBC button or using PIN Code. z On the side of Vigor 2710 series which served as an AP, press WPS button once on the front panel of the router or click Start PBC on web configuration interface. On the side of a station with network card installed, press Start PBC button of network card. z If you want to use PIN code, you have to know the PIN code specified in wireless client.
Below shows Wireless LAN>>WPS web page: 1. Check Enable WPS to enable WPS setting. 2. Click Start PBC to invoke Push-Button style WPS setup procedure. The router will wait for WPS requests from wireless clients about two minutes. The WPS LED on the router will blink fast when WPS is in progress. It will return to normal condition after two minutes. (You need to setup WPS within two minutes). 3. Please input the PIN code specified in wireless client you wish to connect, and click Start PIN button.
3.3.2 DECT Phone Connection (for VDn model only) Vigor2710 provides a DECT phone resolution for users to utilize DECT phone for dialing VoIP/PSTN calls. Without the limitation of cable connection, ECT phone can be placed in any place in your house. People do not worry about being wiretapped for the content of the call will be encrypted and secure. Vigor 2710 VDn provides a DECT GAP/CAT-iq base module, which can facilitate 4 simultaneous wireless audio connections and 6 phone registeration. 1.
3. When the registration is finished, openVoIP>>SIP Accounts. The Registered DECT phone will be available for you to choose. Choose the one you need. 4. Open VoIP>>Status. Information for the active DECT phone will be shown as follows.
When registering with DECT phone, you will be asked to type access code. The default setting in Vigor2710VDn is 1234. Please open VoIP>>Phone Settings to modify it if required. The following diagram shows the brief construction of DECT phone (handset) and Vigor router.
4. Trouble Shooting This section will guide you to solve abnormal situations if you cannot access into the Internet after installing the router and finishing the web configuration. Please follow sections below to check your basic installation status stage by stage. ¾ Checking if the hardware status is OK or not. ¾ Checking if the network connection settings on your computer are OK or not. ¾ Pinging the router from your computer. ¾ Checking if the ISP settings are OK or not.
4.2 Checking If the Network Connection Settings on Your Computer Is OK or Not Sometimes the link failure occurs due to the wrong network connection settings. After trying the above section, if the link is stilled failed, please do the steps listed below to make sure the network connection settings is OK. For Windows The example is based on Windows XP. As to the examples for other operation systems, please refer to the similar steps or find support notes in www.draytek.com. 1.
4. Select Obtain an IP address automatically and Obtain DNS server address automatically. For Mac OS 1. Double click on the current used Mac OS on the desktop. 2. Open the Application folder and get into Network. 3. On the Network screen, select Using DHCP from the drop down list of Configure IPv4.
4.3 Pinging the Router from Your Computer The default gateway IP address of the router is 192.168.1.1. For some reason, you might need to use “ping” command to check the link status of the router. The most important thing is that the computer will receive a reply from 192.168.1.1. If not, please check the IP address of your computer. We suggest you setting the network connection as get IP automatically. (Please refer to the section 4.2) Please follow the steps below to ping the router correctly.
4.4 Checking If the ISP Settings are OK or Not Open Internet Access page and then check whether the ISP settings are set correctly. Click PPPoE/PPPoA/MPoA/Multip-PVCs link to review the settings that you configured previously. Take PPPoE User as an Example 1. Check if the Enable option is selected. 2. Check if Username and Password are entered with correct values that you got from your ISP.
4.5 Problems for 3G Network Connection When you have trouble in using 3G network transmission, please check the following: Check if USB LED lights on or off You have to wait about 15 seconds after inserting 3G USB Modem into your Vigor2710. Later, the USB LED will light on which means the installation of USB Modem is successful. If the USB LED does not light on, please remove and reinsert the modem again. If it still fails, restart Vigor2710.
4.6 Backing to Factory Default Setting If Necessary Sometimes, a wrong connection can be improved by returning to the default settings. Try to reset the router by software or hardware. Warning: After pressing factory default setting, you will loose all settings you did before. Make sure you have recorded all useful settings before you pressing. The password of factory default is null. Software Reset You can reset the router to factory default via Web page via administrator’s operation.
After restore the factory default setting, you can configure the settings for the router again to fit your personal request. 4.7 Contacting Your Dealer If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.
