DRAYTEK VIGOR 2500 SERIES 1
Vigor2500 series introduction ADSL Routers Annex A / Annex B ISDN Backup Wireless AP Vigpr2500 Vigpr2500We * * * */* */* */* ~ ~ ~ ~ * * Vigpr2500Wt The Vigor2500 series is an Internet access solution for your LAN which not only provides shared web surfing but countless other value-added features such as security, VPN and multimedia support, all in a reliable one-box solution. LED Indicators and Back Panels Each of the Vigor2500 series router has different front and rear panels.
Vigor2500 LED Indicators Descriptions ACT(Activity) Blink when power is supplied to the router and the router is running normally. LINE ON when the ADSL network is correctly setup ADSL LAN 1-4 DATA Blinking indicates the DSL protocols start handshaking.The light will remain still when data transmission is available. Link Local Area Network port status. A steady LED indicates a connection between computers on your LAN. A flickering LED indicates data transmission.
Vigor2500We LED Indicators Descriptions ACT(Activity) Blink when power is supplied to the router and the router is running normally. ON when the ADSL network is correctly setup LINE ADSL LAN 1-4 VPN WL Back Panels ON/OFF PWR P1,P2,P3,P4 ADSL Factory Reset DATA Blinking indicates the DSL protocols start handshaking.The light will remain still when data transmission is available. Link Local Area Network port status. A steady LED indicates a connection between computers on your LAN.
Vigor2500Wt LED Indicators Descriptions ACT(Activity) Blink when power is supplied to the router and the router is running normally. ON when the ADSL network is correctly setup LINE ADSL LAN 1-4 VPN WL Back Panels ON/OFF PWR P1,P2,P3,P4 ADSL Factory Reset DATA Blinking indicates the DSL protocols start handshaking.The light will remain still when data transmission is available. Link Local Area Network port status. A steady LED indicates a connection between computers on your LAN.
Copyright Declarations Copyright © 2003 All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: . Microsoft is a registered trademark of Microsoft Corp. .
affect the usability of the product will not be covered by the warranty.We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes. European Community Hereby, we declare that the router is in compliance with the essential requirements and other relevant provisions of R&TTE Directive 99/5/EC. Be A Registered Owner Web registration is preferred.
Vigor2500 Series Quick Start Guide Aim of this chapter Delivery check Quickly connect your router to the Internet Check your router package for the following items : The Router 1 printed Quick Start Guide with warranty/ registration card 1 CD includes detailed User Manual in electronic form, released firmware and utilities 1 AC/DC power supply adapter (black) 1 Ethernet LAN cable (blue) for connection to a computer or hub 1 ADSL line cable (RJ-11 or RJ-45, black) 1 external antenna for Vigor2500We/Wt Id
What you need from ISP DSL line Depending on the variant Vigor2500 series you purchased, the following DSL service must be available at your local premisses: ADSL/POTS : ADSL service must be enabled on your POTS telephone line. ADSL/ISDN : ADSL service must be enabled on your ISDN telephone line. DSL Parameters It should provide at least the following information from ISP : 1. The VPI/VCI of the virtual channel to use on the DSL line 2. Protocol : PPPoE, PPPoA or MPoA (RFC1483/2684) 3.
Example: VPI/VCI = 0/33 Protocol = PPPoA Encapsulation Method = VCMUX Modulation Method = G.DMT Username/Password Only for PPPoE/PPPoA mode users Fixed IP Address/ Subnet Mask/ Gateway IP Address Only for MPoA mode users. Some ISP will use DHCP method to provide IP address for MPoA mode users, then users do not need to know the fixed IP address. If you do not know these information in detail, please contact your ISP to get these informations.
You must wire Ethernet port (between router and PC), DSL port and Power port as below: Vigor2500 Vigor2500We/Wt 11
Install ‘ Router Tools ‘ This tool which provides ‘Quick StartWizard’, ‘Firmware Upgrade Program ’ and ‘Syslog Monitor’ client is in the attached CD. It supportsWindows, Mac OS 8/9 and Mac OS X. Turn on your router Once all previous steps are completed, turn on your router. After Power is on, the ‘ACT’ LED and corresponding LAN port LED will light. If the LEDs do not light normally, please refer to section A, ‘Trouble Shooting’, for furthur information.
Enter Router Menu Once past the password prompt, you will now see the router’s main menu: (Example: Vigor2500) Set DSL Parameters Click on ‘Internet Access Setup’ on the right-hand menu. You will find two items : PPPoE/PPPoA and MPoA (RFC 1483/2684). Then You can continuely enter setting menu according to the protocol which ISP assigns.
For PPPoE/PPPoA Users Enter your allocated username, password and DSL parameters according to the information provided by your ISP. If you want to connect to Internet all the time, you can check ‘Always On’. For MPoA (RFC 1483/2684) Users Enter your allocated WAN IP address(or enabling DHCP client to get IP from ISP) and DSL parameters according to the information provided by your ISP.
Auto detect ATM/ DSL Setting You can also use this function to detect ATM/ DSL setting. Please follow the instructions to operate. If your country is not in the list, it may take longer time to detect. Surfing Internet Once all previous steps are completed, you can surf Internet now. You can also monitor the connection condition via router management function. (Example: Vigor2500) Wireless LAN Setting Wireless setting is for Vigor2500We and Vigor2500Wt only.
Wireless LAN Interface The Vigor2500We and Vigor2500Wt are equipped with a wireless LAN interface compliant with the 11 Mbps IEEE 802.11b protocol. The speed of Vigor2500Wt can up to 22 Mbps. The features of wireless LAN capability enable high mobility of several simultaneous users accessing all LAN facilities just like on a wired LAN as well as Internet and WAN access. The Frequency Domain is set as Europe and the MAC address will show as above.
SSID(Service Set Identification): You should set the SSID same as your note book wireless card to allow the client PCs to access the network via the wireless LAN interface. The default SSID is "default". Channel: To select a wireless channel for Vigor2500We / Vigor2500Wt. The default channel is 6. Hide SSID: To check it to hide SSID when the wireless clients sniffing radio.
Access Control of Wireless LAN Interface For additional security of wireless access, the Access Control allows your to restrict the network access rights by the wireless LAN MAC address of client. Only the valid MAC address which has been configured can allow to access the wireless LAN interface. Enable Acces Control: To check the Enable Access Control to enable the MAC Address access control feature.
Trouble Shooting for Can not get on to the Internet Check if the hardware is OK? Check if the power and LAN line are connected correctly. After power is on, the ‘ ACT ‘ LED will blink once a second, and the correspondent LAN port will light.
The default gateway IP of router is 192.168.1.1. Please check if you can ping router correctly. For Windows For Mac(Terminal) If not, please check the IP address of your PC.
For Win98/ Me user 1. Enter “Control Panel” and double click “Network”. 2. Choose “TCP/IP of LAN device” and press “ Properties”. 3.
For Win2000 user 1. Enter “Control Panel” and double click “Network and Dial-up Connections”. 4. Select ‘Obtain an IP address automatically’ 2. Right click “Local Area Connection” and choose “Properties”. 3. Choose “TCP/IP” and press “Properties”.
For XP user 1. Enter “Control Panel” and double click “Network Connections”. 4. Select “Obtain an IP address automatically” 2. Right click LAN icon and choose “Properties”. 3. Choose “TCP/IP” and press “Properties”.
For Mac OS9.
Are DSL/ ISP settings Ok? Connect to router Web Configurator. (Example: Vigor2500) Check if the setting of DSL is ok. (For MPoA users, please refer to the MPoA explanation on page 24 ) —> VPI/VCI/Modulation mode: T1.413, G.Lite, G.
—>Encapsulation mode: VCMUX or LLC/SNAP For PPPoE/PPPoA user, please check if user name/ password provided by ISP are correct or not.
For MPoA (RFC1483/2684) mode users, please check if the WAN IP/ Gateway/ Namemask is set or ISP requires you to use DHCP client to get WAN IP. Check DSL Status You can know the DSL status via status monitor. (Example: Vigor2500) Report to people who concerned if still can not work If the router setting is OK and your PC on the LAN can also talk to router successfully, there may be wrong settings on DSL (eg. VPI, VCI, modulation etc...) when there is still no ADSL Internet connection.
