Operation Manual
Vigor2832 Series User’s Guide
69
9
-w [number] Specify the WAN interface.
Value: Type the number of WAN interface. 1: WAN1; 2:WAN2….and
etc.
-I [Host/IP address] Specify the IPv4 target to detect. If can be an IPv4 address or
domain name.
Host/IP address: Type the IP address/domain name of the target.
-s [base_size] Set the MTU size base for Discovery.
base_size: Available setting is 1000 ~ 1500.
-d [decrease size] Set the MTU size to decrease between detections.
decrease size: Available setting is 1 ~ 100.
-c [count] Set the maximum times of ping failure during a Discovery.
count: Available settings are 1 ~ 10. Default value is 3.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> wan detect_mtu -w 2 -i 8.8.8.8 -s 1500 -d 30 -c 10
detecting mtu size:1500!!!
mtu size:1470!!!
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
w
w
a
a
n
n
d
d
e
e
t
t
e
e
c
c
t
t
_
_
m
m
t
t
u
u
6
6
This command allows you to run a WAN MTU Discovery. The user can specify an IPv6 target to
ping and find the suitable MTU size of the WAN interface.
S
S
y
y
n
n
t
t
a
a
x
x
wan detect_mtu6 –w [number] –i [IPv6 address] –s [base_size]
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
-w [number] Specify the WAN interface
number: Type the number of WAN interface. 1: WAN1; 2:WAN2….and
etc.
-I [IPv6 address] Specify the IPv6 target to detect. It must be an IPv6 IP address.
IPv6 address: Type the IPv6 address of the target.
-s [base_size] Specify the size of MTU.
base_size: Available setting is 1000 ~ 1500.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> wan detect_mtu6 -w 1 -i 2404:6800:4008:c06::5e -s 1500
>
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
h
h
s
s
p
p
o
o
r
r
t
t
a
a
l
l
This command is used to configure a profile (Hotspot Web Portal) with specified URL for
accessing into or display a message when a wireless/LAN user connects to Internet through
this router.
S
S
y
y
n
n
t
t
a
a
x
x
hsportal -p <profile> [-l <lan>] [-s <ssid>] ...
hsportal -p <profile> -c
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
-p Indicate available profile to be configured.
Number of profile: 1 /2 /3 / 4.