Table of Contents 0. Preface ..................................................................... 0-1 0.1 About This Manual ........................................... 0-2 0.2 Copyright Declarations .................................. 0-2 0.3 Trademarks ........................................................ 0-2 0.4 How To Become A Registered Owner ........ 0-2 0.5 Safety Instructions ........................................... 0-3 0.6 Warranty ..............................................................
.5 Using the Web Configurator .......................... 2-18 3. Basic Setup & Internet Access .................. 3-1 3.1 Basic Setup .......................................................... 3-2 3.2 Internet Access Setup ....................................... 3-7 3.3 ISDN Dial-up Internet Access ......................... 3-9 3.4 DSL/Cable Modem Internet Access ............... 3-12 4. Remote Access ................................................... 4-1 4.1 Introduction to Remote Access ...............
6. Virtual TA Application .................................... 6-1 6.1 Virtual TA Concepts ............................................ 6-2 6.2 Installing a Virtual TA Client .............................. 6-3 6.3 Configuring a Virtual TA Client/Server ........... 6-4 7. System Management ...................................... 7-1 7.1 Online Status ........................................................ 7-2 7.2 Management Setup ............................................. 7-5 7.3 Diagnostic Tools .......
0 Preface 0.1 About This Manual 0.2 Copyright Declarations 0.3 Trademarks 0.4 How To Become A Registered Owner 0.5 Safety Instructions 0.6 Warranty 0.
Preface 0.1 About This Manual This manual is designed to assist users in using the DrayTek Vigor2200 series router, including the Vigor2200, Vigor2200X and Vigor2200E. Information in this document has been carefully checked for accuracy; however, no guarantee is given as to the correctness of the contents. The information contained in this document is subject to change without notice. Should you have any inquiries, please feel free to contact support@draytek.com.tw .
Preface 0.5 Safety Instructions • Please read the installation guide thoroughly before you set up the router. • The router can be used only with a BRI (Basic Rate Interface) ISDN line, except for the Vigor2200E model. • The router is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the router yourself. • Do not place the router in a damp or humid place, e.g. a bathroom.
Preface store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors.
1 Getting Started 1.1 Introduction 1.2 Vigor2200 Series Router Comparisons 1.3 Unpacking Your Vigor2200 Series Router 1.4 LED Indicators & Rear Panels 1.
Getting Started 1.1 Introduction The Vigor2200 series of routers is composed of the Vigor2200, the Vigor2200X, and the Vigor2200E. The Vigor2200E has no ISDN BRI interface. Therefore, no ISDN functions are available for the Vigor2200E and parts of this manual referring to such functions will not apply to the Vigor2200E. From a technical point of view, the Vigor2000 and Vigor2200X are broadband DSL/Cable routers within another WAN interface ---ISDN BRI.
Getting Started 1.2 Vigor2200 Series Router Comparisons Items\Models Vigor2200 Vigor2200X Vigor2200E ISDN BRI Yes Yes No LAN1 1*10/100 Base- TX 4*10/100Base- TX 4*10/100Base- TX LAN2(WAN) 10Base- T 10Base- T 10Base- T Broadband Access Capability DSL/Cable Modem DSL/Cable Modem DSL/Cable Modem LAN- to- LAN via ISDN Yes Yes No ISDN Dial- Backup Yes Yes No The above table shows a brief comparison of the Vigor2200 series routers: the Vigor2200, Vigor2200X and Vigor2200E.
Getting Started 1.3 Unpacking Your Vigor2200 Series Router Your Vigor2200 series router package should contain the items listed below. If any item is missing or damaged, contact your dealer or DrayTek Customer Service Department immediately. • One User manual with warranty/registration card • One CD-ROM; includes User Manual in electronic form, lastest released firmware, and utilities • One RJ-45 ISDN telephone cable (black). Note that the Vigor2200E package does not contain this cable.
Getting Started 1.4 LED Indicators & Rear Panels Each of the Vigor2200 series front and rear panel are different. The following sections describe the models individually. Vigor2200: LED Indicators There are eleven LEDs on the front panel; ACT, LNK, B1, B2, LNK, 100M, FDX, Broadband, LNK, TX, and Col. ACT (Activity) Blinks when power is supplied to the router and the router is running normally. ISDN Group: LNK (Link) ON when the ISDN network is correctly setup.
Getting Started Note: On some NT-1 boxes, the ISDN LNK LED will go OFF when the ISDN line has been idle for a while. When the router is dialling or answering a call, it should be ON again. B1 ON when there is a successful remote connection on the ISDN BRI B1 channel. B2 ON when there is a successful remote connection on the ISDN BRI B2 channel. LAN1 Group: LNK (Link) ON when the connected network card or hub has linked up. Blinking when Ethernet packets pass through the interface.
Getting Started TX (Transmit) Blinks when the LAN2(WAN) port transmits data. Col (Collision) ON when there are collisions occurring on the LAN2(WAN) port. Rear Panel Description The Vigor2200 has a reset button, a power jack, and five RJ-45 ports on the rear panel: PWR Only the DrayTek supplied power adapter should be connected to the power jack. Reset For firmware upgrades: Press and hold the button, then power ON. The ACT and LNK LEDs will blink simultaneously (see section 7.5).
Getting Started Vigor2200X: LED Indicators As shown above, there are 11 LEDs on the front panel. Reading from left to right, they are marked ACT, LNK, B1, B2, Backup, WAN, Broadband, P1, P2, P3 and P4. Their functions are as follows: ACT(Activity) Blinks when power is supplied to the router and the router software is running normally. ISDN Group: LNK (Link) ON when the ISDN network is correctly setup. Note: For some NT-1 boxes, the ISDN LNK LED will go OFF when the ISDN line has been idle for a while.
Getting Started B1 ON when there is a successful remote connection on the ISDN BRI B1 channel. B2 ON when there is a successful remote connection on the ISDN BRI B2 channel. Backup ON when ISDN backup dial is active. WAN Group: WAN ON when the WAN port is connected. Broadband ON when broadband access is active. P1, P2, P3, P4 These indicators are dual-color LEDs: Yellow means the port is connected to a 10Mbps device, and Green indicates the connected device is 100Mbps.
Getting Started Reset For upgrading the firmware: Press the button and hold, then power ON. The ACT and LNK LEDs will blink simultaneously (see section 7.5). To restore default settings: While the device is running, press the button and hold for more than five seconds. When the ACT LED begins to blink rapidly, release the Reset button. The router will restart with the default configuration. Uplink ... P4 These ports are the same Ethernet port with a mutual crossover.
Getting Started Vigor2200E: LED Indicators As shown above, there are 11 LEDs, reading from left to right, they are ACT, four bandwidth utilization bar LEDs for the WAN port, WAN, Broadband, P1, P2, P3 and P4. Most of the LEDs are the same as those of the Vigor2200X, except for the additional Bandwidth Utilization LEDs for the WAN port. The following describes only the difference. There are four LEDs below the bandwidth utilization bar.
Getting Started 1.5 Key Features The Vigor2200 Routers provide many built-in server and software features to provide a convenient comprehensive solution for your SOHO network. 1. Network Address Translation (NAT): NAT allows multiple SOHO users to concurrently connect to an Internet Service Provider (ISP) using a single Internet access account. 2.
Getting Started 6. Routing Information Protocol (RIP) Support: Used in most LAN-to-LAN applications. The RIP protocol exchanges routing information between routers. 7. Domain Name Server (DNS) Proxy: The DNS proxy maintains a DNS cache, including a mapping table of domain names and IP addresses. The proxy also remembers DNS query packets sent through the router and saves them into its own DNS cache. For enhanced speed, when a DNS query packet enters the router, the proxy searches its local DNS cache.
Getting Started 13. Point-to-Point Tunnelling Protocol (PPTP) Client Support: Some DSL modems (e.g. Alcatel modems), only provide a PPTP local connection for an end user computer. The Vigor2200 series routers have a built-in PPTP client for establishing a DSL link transport protocol for your entire local network. There is no need to install a PPTP client driver on your computers. 14.
2 Installation & Setup 2.1 Before you Begin 2.2 Hardware Installation 2.3 Setting up a Management PC 2.4 Using the Smart Start Wizard 2.
Installation & Setup 2.1 Before You Begin 1. Use only the power adapter supplied by DrayTek Corp. Using an incorrectly rated power adapter will result in damage to the router. 2. Know the type of interface provided by your ISP or telcom. The standard model only supports the ISDN BRI S/T-interface. If you are an ISDN U-interface user, you need to order a U-interface model. If you are an ISDN S/T-interface user, you should have an NT-1 or NT-1 plus provided by your ISP or telcom.
Installation & Setup Factory Default Settings: Router’s Default IP Network Settings: IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 DHCP Server: Enabled Start IP Address: 192.168.1.10 IP Pool Counts: 50 Web Configurator: Username: admin Password: Note: Blank means no password required. Telnet Console: Password: Note: Blank means no password required. Management from the Internet: Not allow. The following items apply only to the Vigor2200 and Vigor2200X.
Installation & Setup 2.2 Hardware Installation 2.2.1 Connecting the Power Adapter 1. Connect the power adapter to the power outlet on the wall and to the PWR power jack on the rear panel of the router. 2. The ACT LED should be blinking once every 2 seconds. 2.2.2 Connecting to the Ethernet A. Connecting to a PC: 1. Attach the Ethernet cable (blue color cable) to the LAN 1 port (Vigor2200) or to any P1 ~ P4 port (Vigor2200X, Vigor2200E). 2.
Installation & Setup Ethernet hub or switch should be ON. Note: If the Ethernet cable is not long enough to reach the external hub/switch, purchase a longer straight-through 10Base-T Ethernet cable. 2.2.3 Connecting to an ISDN BRI Line (Vigor2200 and Vigor2200X only) A. S/T-Interface Model 1. Locate the ISDN cable (black color cable). 2. Plug one of the RJ-45 connectors on the cable into the ISDN port on the rear panel of the router. 3.
Installation & Setup 2. Attach the Ethernet cable to the Ethernet port of the DSL/ Cable modem. 3. Plug the other end of the cable into the WAN port. The hardware installation is now complete. The following sections will guide you through setting up your management PC and connecting to the Web Configurator. Note: The Web Configurator is a management utility that handles all configuration and provides web-based management.
Installation & Setup 2.3 Setting Up a Management PC The router has a built-in HTTP (Web) server for configuration. Before you use the router to access the Internet, you should set up a management PC to log into the router for further configuration. The management PC may be configured with a fixed or dynamically assigned IP address. For a fixed IP address, use an IP address from a 192.168.1.0/24 network, such as 192.168.1.2.
Installation & Setup Your particular system will be different from the screen shown here. Check that you have an Ethernet network card installed. If not, refer to the card manufacturers documentation and install the card and drivers. If your card is installed, 1. Click the “Add” button. The Select Network Component Type dialog box will open. The box will show four options: Client, Adapter, Protocol, Service. 2. Select Protocol and click the “Add” button. The Select Network Protocol dialog box will open. 3.
Installation & Setup 2.3.2 Configuring the TCP/IP Protocol 1. On the Network dialog box Configuration card, select TCP/IP and then click “Properties”. The TCP/IP Properties dialog box will open. 2. On the IP Address tab, click “Obtain an IP address automatically”. As the DHCP (Dynamic Host Configuration Protocol) server built into the router is enabled by default, your computer will get an IP address, subnet mask, and other related IP network settings from the router. 3.
Installation & Setup 4. Click the “Gateway” tab.
Installation & Setup 5. Make the “New gateway” and “Installed gateways” fields blank and click “OK”. A dialog box will pop up asking you to restart the PC. Click “Yes”. 2.3.3 Checking TCP/IP settings 1. After completing the previous steps, click “Start” -> “Run” -> and type “winipcfg”. The IP Configuration window will open. If the PC does not show an IP address in the 192.168.1.2 to 192.168.1.254 range, click the “Release” button to release the current configuration.
Installation & Setup not, verify that the Ethernet cable is connected to the router properly and the Ethernet port LED on the front panel is lit.
Installation & Setup 2.4 Using the Smart Start Wizard The Smart Start Wizard will guide you through using the Web Configurator or Telnet Terminal (command-line based management). Also, if your currently installed network is not located in the 192.168.1.x IP range, the wizard will find the router and change the router’s default IP address and IP mask to match the current network. If you are familiar with using a web browser (Microsoft Internet Explorer, Netcape Communicator, etc.
Installation & Setup The following screen will open. 2. Click “Search” to find the router on your network. 3. Click “OK” to go to the login password screen. 3. If this is a first time setup of the router, do not enter a password. Click ”OK“ to go to next screen.
Installation & Setup The screen shows read-only IP and IP mask settings for the PC you are using, and also the IP Address and IP Mask settings for the router. Here you may change the router settings to match your current network environment, or keep the default settings. 4. Click “Next” to update the settings to the router. 5. Wait for a few seconds. The “Telnet” and the “Browser” buttons will become active (see the next page).
Installation & Setup If the IP address and IP Mask of your PC and of the router are not located on the same subnet, renew your PC’s IP address, using winipcfg.exe on Windows95/98/Me,or ipconfig.exe on Windows NT/2000. When the browser is launched, the following pop-up window will ask for a User Name and Password. Enter admin as the User Name and leave the Password field blank. The Web Configurator will open. In the following examples we use the NetscapeTM web browser (see the next page).
Installation & Setup 2-17
Installation & Setup 2.5 Using the Web Configurator 2.5.1 Connecting to the Web Configurator via a Web Browser 1. Launch the Web browser. Enter http://192.168.1.1 into the browser Address window and press the Enter key. 2. An authentication dialog box will open. 3. If this is a first time setup of the router, type admin as the User Name and leave the Password field blank. Click ”OK”. 4. The Web Configurator Setup Main Menu will open.
Installation & Setup 2.5.2 Overview of the Web Configurator The Setup Main Menu (see above figure) consists of four groups: Basic Setup (Setup First), Quick Setup, Advanced Setup, and System Management. The following outlines each configuration menu. Basic Setup (Setup First): 1. Administrator Password Setup: Sets/changes the administrator password. 2. LAN1 TCP/IP and DHCP Setup: Modifies the router’s IP address and DHCP server settings. 3.
Installation & Setup ing settings, e.g. MSN numbers and Own (Calling) numbers. Quick Setup: 1. Internet Access Setup: (required for Internet access) Usually the router functions as a border router for SOHO or home networking so you must enter settings here to enable access to the Internet. 2. Remote Dial-In Access Setup: (Vigor2200, Vigor2200X) Remote access or LAN-to-LAN remote access settings are made here. 3.
Installation & Setup 2. NAT (Network Address Translation) Setup Sets NAT configurations, such as Port Redirection, DMZ etc. 3. Static Route Setup This menu has 10 routing rules for static routing usage. Here you may add/delete or activate/deactivate any static route. 4. Remote Dial-in User Setup (Vigor2200, Vigor2200X) The Vigor2200 and Vigor2200X support 10 remote dial-in accounts for remote access applications. You can manage these dial-in accounts from this menu. 5.
Installation & Setup 2. Management Setup The item allows you to set or limit access rights to manage the router. Also, you may set HTTP or Telnet ports to specific port numbers of your choice. 3. Diagnostic Tools Diagnostic tools offers useful tools for diagnosing the router or your network, e.g. view ARP table, routing table, NAT port map, DHCP server status, last triggered packet, etc. 4. Reboot System You can restart the router with the default configuration or with the current running configuration.
3 Basic Setup & Internet Access 3.1 Basic Setup 3.2 Internet Access Setup 3.3 ISDN Dial-up Internet Access 3.
Basic Setup & Internet Access The Web Configurator Setup Main Menu includes four groups: Basic Setup (Setup First), Quick Setup, Advanced Setup, and System Management. This chapter explains the Basic Setup group and Internet Access Setup (which is in the Quick Setup group). 3.1 Basic Setup (Setup First) This group includes Administrator Password Setup, LAN 1 TCP/IP and DHCP Setup and ISDN Setup. The Vigor2200E model does not offer an ISDN interface and therefore does not have the ISDN Setup menu. 3.1.
Basic Setup & Internet Access Old Password: If this is the first time to set a password, leave this field blank. New Password: Enter an administrator password. Retype New Password: Type the password again for confirmation. Click “OK”. 3.1.2 Configuring LAN 1 IP Address and DHCP Server Each of the Vigor2200 series routers has two Ethernet interfaces, one is for connecting to local network users, the other is for connecting to an external broadband device (i.e. DSL modem/router or Cable modem).
Basic Setup & Internet Access LAN 1 IP Network Configuration 1st IP Address: Private IP address for connecting to a local private network (Default: 192.168.1.1). 1st Subnet Mask: Netmask for the local private network (Default: 255.255.255.0/24). For IP Routing Usage: (Default: Disable). Enable: Enables the 2nd IP address settings. Disable: Disables the 2nd IP address settings. 2nd IP Address: Sets a public IP address. 2nd Subnet Mask: Sets a netmask for the public IP address.
Basic Setup & Internet Access the local network. Activate: (Default: Yes). Yes: Enables the DHCP server. No: Disables the DHCP server. Start IP Address: Sets the start IP address of the IP address pool. IP Pool Counts: Sets the number of IPs in the IP address pool. DNS Server IP Address: (Default: None). DNS stands for Domain Name System. Every Internet host must have a unique IP address, also they may have a human friendly, easy to remember name such as www.yahoo.com.
Basic Setup & Internet Access 3.1.3 Configuring the ISDN Interface This setup page is present in the Vigor2200 and Vigor2200X, absent in the Vigro2200E. Country Code: For proper operation on your local ISDN network you should set the correct country code. Own Number: Sets your ISDN number. If the field has been configured, every outgoing call will carry the number to the called user. MSN Numbers for the Router: “MSN Numbers” means that the router is able to accept numbermatched incoming calls.
Basic Setup & Internet Access without number-matching. Click “OK” to return to the Main Setup Menu. 3.2 Internet Access Setup For most users, Internet access is the primary application. The Vigor2200 and Vigor2200X support the ISDN WAN interface for Internet access and remote access. The following sections will explain more details of ISDN dial-up access and broadband access setup. When you click “Internet Access Setup” from within the Quick Setup group, the following setup page will be shown.
Basic Setup & Internet Access do not support Multiple-Link PPP (ML-PPP). In such cases dialing to two ISPs can increase the bandwidth utilization of the ISDN line to 128kbps data speed. PPPoE: This is for most DSL modem users. All local users can share one PPPoE connection to access the Internet. PPTP: Some DSL services providers supply a special DSL modem (e.g. Alcatel’s DSL modem). This kind of modem only supports the PPTP tunnel method to access the Internet.
Basic Setup & Internet Access 3.3 ISDN Dialup Internet Access 3.3.1 Connecting to a Single ISP ISP Access Setup ISP Name: Enter your ISP name. Dial Number: Enter the ISDN access number provided by your ISP. Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Require ISP Callback (CBCP): If your ISP supports the callback function, check “Require ISP Callback (CBCP)” to enable the Callback Control Protocol during PPP negotiations.
Basic Setup & Internet Access Link Disable Disables the ISDN dial-out function. Dialup 64Kbps Uses one ISDN B channel for Internet access. Dialup 128Kbps Uses both ISDN B channels for Internet access. Dialup BOD BOD stands for bandwidth-on-demand. The router will use only one B channel under low traffic situations. Once the single B channel bandwidth is filled, the other B channel will be dialled automatically.
Basic Setup & Internet Access check “Yes” and enter the IP address in the Fixed IP Address field. Click “OK”. 3.3.2 Connecting to Dual ISPs Most configuration parameters are the same as that in the last section. This page provides an “Enable Dual ISPs Function” check box and adds a secondary ISP Setup section. Check the box and enter the second ISP information.
Basic Setup & Internet Access 3.4 DSL/Cable Modem Internet Access Before you connect a broadband access device, e.g. a DSL/Cable modem, to the router, you need to know what kind of Internet access is provided by your ISP. The following sections deal with four widely-used broadband access services. These are PPPoE Client, PPTP Client and Static IP for DSL, and Dynamic IP (DHCP Client) for Cable. In most cases, you will get a DSL or Cable modem from the broadband access service provider.
Basic Setup & Internet Access 3.4.
Basic Setup & Internet Access Click “Internet Access Setup” > “PPPoE” to enter the setup page. PPPoE Setup PPPoE Link: Check “Enable” to enable the PPPoE client protocol on the LAN2 interface. ISP Access Setup ISP Name: Enter the ISP name. Username: Enter the ISP supplied username. Password: Enter the ISP supplied password. ISDN Dial Backup Setup This item will be described in more detail in section 3.4.5. PPP/MP Setup PPP Authentication: Select “PAP or CHAP” for widest compatibility.
Basic Setup & Internet Access seconds. If you set the time to 0, the PPP session will not terminate itself. IP Address Assignment Method (IPCP) Fixed IP: Check “No (Dynamic IP)” unless your ISP has provided you with a static IP address. Fixed IP Address: If your ISP has provided you with a static IP address enter it here. Click “OK”. 3.4.2 Using PPTP with a DSL Modem Click “Internet Access Setup” > “PPTP” to enter the setup page. The following setup page is just for example.
Basic Setup & Internet Access ISP Access Setup ISP Name: Enter the ISP name. Username: Enter the ISP supplied username. Password: Enter the ISP supplied password. ISDN Dial Backup Setup This item will be described in more detail in section 3.4.5. PPP Setup PPP Authentication: Select “PAP or CHAP” for widest compatibility. Idle Timeout: Idle timeout means the router will disconnect after being idle for a preset amount of time. The default is 180 seconds.
Basic Setup & Internet Access IP Address Assignment Method (IPCP) Fixed IP: Check “No (Dynamic IP)” unless your ISP has provided you with a static IP address. Fixed IP Address: If your ISP has provided you with a static IP address enter it here. LAN2/WAN IP Network Settings Obtain an IP address automatically: Sets the LAN2/WAN interface as a DHCP client that will ask for the IP network settings from the DHCP server or PPTP-enabled DSL modem.
Basic Setup & Internet Access Click “Internet Access Setup” > “Static or Dynamic IP” to enter the setup page.
Basic Setup & Internet Access Access Control Broadband Access: Select “Enable” to turn on the broadband access capability. ISDN DIAL Backup Setup This item will be described in more detail in section 3.4.5 LAN2/WAN IP Network Settings Specify an IP address: As we are using a static IP, you have to select the option to specify an IP Address, Subnet Mask, and Gateway IP Address. Click “OK”. Note: The router should be restarted to allow the settings to take effect. 3.4.
Basic Setup & Internet Access 3-20
Basic Setup & Internet Access Access Control Broadband Access: Select “Enable” to turn on the broadband access capability. ISDN Dial Backup Setup This item is described in more detail in section 3.4.5 LAN2/WAN IP Network Settings Obtain an IP address automatically: The option must be enabled. Router Name: Depending on your Cable ISP this option may or may not be left blank. Some ISPs require this name for access authentication.
Basic Setup & Internet Access 3.4.5 Configuring ISDN Dial Backup As the Vigor2200E has no ISDN interface, it does not support the ISDN dial backup function. Therefore, the following setup options will not be available for this model. ISDN Dial Backup Setup Dial Backup Mode: None: Disables the backup function. Packet Trigger: The backup line is disconnected until a packet from a local host triggers the router to establish a connection.
Basic Setup & Internet Access For ISDN Dial Backup to function, you must create a dial backup profile. Click “Internet Access Setup” > “Dialing to a Single ISP” to enter the backup profile setup page. Refer to section 3.3.1 for details.
4 Remote Access 4.1 Introduction to Remote Access 4.2 Remote Dial-in Access 4.
Remote Access This chapter explains the capabilities of remote access on the Vigor2200 series routers. Use the following setup links on the Setup Main Menu to setup remote access functions.
Remote Access 4.1 Introduction to Remote Access Here the term “Remote Access” covers two types of remote access. The first, “Remote Dial-In Access” means the router allows normal ISDN TA users or NAT routers (IP sharing routers) to dial into the router to share the network resources of the local network, or to surf the Internet via a broadband device connected to the LAN2/WAN port.
Remote Access Dial-In Access Control Dial-In Service: Check “Enable” to allow dial-in service. Note that if you check “Disable”, the router will not accept any incoming ISDN calls. PPP/MP Setup Dial-In PPP Authentication: PAP: Selecting this option will force the router to authenticate dial-in users with the PAP protocol. PAP or CHAP: Selecting this option means the router will attempt to authenticate dial-in users with the CHAP protocol first.
Remote Access 4.2.2 Creating an Access Account for a Dial-in User After activating the dial-in capability, you must create an access account for each dial-in user. From the Advanced Setup menu, click “Remote Dial-In User Setup” to open the page shown below. The router provides 10 access accounts for dial-in users. Set to Factory Default: Clicking here will clear all dial-in user accounts. Index: Click the index number to open an individual setup page for detailed setting of each account.
Remote Access User Account and Authentication Check to enable the user account: Check this item to activate the individual user account. Username: Specifies a username for the specific dial-in user. Password: Specifies a password for the specific dial-in user. Idle Timeout: By default, set to 300 seconds. If the dial-in user is idle for over the limit set by the timer, the router will drop the connection.
Remote Access The router owner will be charged the connection fee by the telecom. Check to enable the Callback function: Enables the callback function. Specify the callback number: The option is for extra security. Once enabled, the router will only call back to the specified ISDN number defined in the next parameter, Callback Number. Callback Number: If the previous option has been enabled, enter the dial-in user’s ISDN line number here.
Remote Access 4.3 LAN-to-LAN Access The following sections are based on the network layout above to describe how to set up a LAN-to-LAN profile to connect two private networks. In the above network layout, the private network 192.168.1.0/ 24 is located at head office, the off-site branch office’s network is 192.168.2.0/24. Before you begin to setup a LAN-to-LAN profile for each network, you should gather the information shown in the following table.
Remote Access Head Office Branch Office Network ID 192.168.1.0/24 192.168.2.0/24 Router IP address/netmask 192.168.1.1/24 192.168.2.1/24 Assigned IP for dial- in connection 192.168.1.200 192.168.2.200 Access Account UN: head PW: head UN: branch PW: branch ISDN line number 1000 2000 Callback Function Disable Disable 4.3.1 Activating the Remote Dial-In Capability In the Quick Setup group of the Setup Main Menu, click “Remote Dial-In Access Setup” to enter the setup page. See 4.
Remote Access Because the Head Office’s network is 192.168.1.0/24, the settings should be as below: Dial-In Service: Enable Start IP Address: 192.168.1.200 Branch Office: Because the Branch Office’s network is 192.168.2.0/24, the settings should be as below: Dial-In Service: Enable Start IP Address: 192.168.2.200 4.3.2 Creating a LAN-to-LAN Dialer Profile After enabling the Dial-in service, you must create a LAN-to-LAN profile for each network.
Remote Access The router provides 16 LAN-to-LAN profiles for connecting to up to 16 different remote networks. Set to Factory Default: Clicking here will clear all the LAN-to-LAN profiles. Index: Click a number in the Index to open a detailed settings page for each profile. Name: Indicates the name of the LAN-to-LAN profile. The symbol “???” means the profile is available. Status: Indicates the status of the individual profiles. The symbol “v” means the profile is active, “x” that it is inactive.
Remote Access Each LAN-to-LAN profile includes 4 subgroups: Common Settings, Dial-Out Settings, Dial-In Settings, and TCP/IP Network Settings. The following will explain each subgroup in detail. Common Settings Profile Name: Specifies a name for the remote network. Enable this profile: Check here to activate this profile. Call Direction: Specifies the call direction for this profile.
Remote Access means it can be used for outgoing and incoming access. DialOut means it can only be used for outgoing access. Dial-In allows only incoming access. Idle Timeout: By default, set to 300 seconds. If the profiles connection is idle for over the limit set by the timer, the router will drop the connection. Dial-Out Settings Username: Specifies a username for authentication by the remote router. Password: Specifies a password for authentication by the remote router.
Remote Access Callback Function (CBCP) The callback function is implemented by the CBCP protocol which is part of the PPP protocol suite. Require Remote to Callback: Inactive by default. When active, the router exchanges connection information with the remote router and requires the remote router to call back to make a connection. Provide ISDN Number to Remote: In some cases, the remote router requires the ISDN number for calling back.
Remote Access Use Following Number to Callback & Callback Number: Check here and enter a callback number for the router to call. Callback Budget: Specifies a time budget for the callback function. By default the value is zero, which means there is no time limitation on call backs. TCP/IP Network Settings The following settings are required for proper LAN-to-LAN operation. My WAN IP: In most cases you may accept the default value 0.0.0.0 in this field.
Remote Access Recall the LAN-to-LAN example described in section 4.3. The LANto-LAN Dialer Profile could be configured as below.
Remote Access Branch Office: 4-17
5 Advanced Setup 5.1 Enabling the Remote Activation Function 5.2 Call Control Setup 5.3 Configuring the BOD Parameters 5.4 NAT Setup 5.5 Static Route Setup 5.
Advanced Setup This chapter explains the options available in Advanced Setup: Advanced Setup > Call Control and PPP/MP Setup > NAT Setup > Static Route Setup > IP Filter/Firewall Setup Note: As the Vigor2200E model does not feature an ISDN interface, Call Control and PPP/MP Setup will not be available.
Advanced Setup 5.1 Enabling the Remote Activation Function Some applications require that the router be remotely activated, or dial up to the ISP using the ISDN interface. For instance, if you are a user who accesses the Internet via ISDN from home, usually the dialup connection is idle when you are not at home. It may be that while working in the office, you want to get some files from home. This function allows you to make a phone call to the router and ask it to dial up to the ISP.
Advanced Setup Specify a phone number in the Remote Activation field. If the router accepts a call from the number 12345678, it will disconnect immediately and dial to the ISP. Note that “Internet Access Setup” > “Dialling to a Single ISP” should be preset properly. 5.2 Call Control Setup On the “Call Control and PPP/MP Setup” setup page, you will see Dial Retry and Dial Delay Interval. These two parameters set global settings for ISDN dialup access.
Advanced Setup These parameters are activated when you set the Link Type to Dialup BOD. Usually the ISDN will use one B channel to access the Internet or remote network when you use the Dialup BOD link type. The router will use the parameters here to make a decision on when to activate/ drop the additional B channel. Note that cps (characters-per-second) measures the total link utilization.
Advanced Setup 5.4 NAT Setup Usually you will use the router as a NAT-enabled router. NAT stands for Network Address Translation. It means the router gets one (in Single ISP, PPPoE, PPTP) or two (in Dual ISP mode) globally rerouteable IP addresses from the ISP. Local hosts will use private network IP addresses defined by RFC-1918 to communiate with the router. The router translates the private network addresses to a globally routeable IP address, which is then used to access the Internet.
Advanced Setup The following example shows how an internal FTP server is exposed to the public domain. The internal FTP server is running on the local host addressed as 192.168.1.10. As shown above, the Port Redirection Table provides10 port-mapping entries for internal hosts. Service Name: Specifies the name for the specific network service. Protocol: Specifies the transport layer protocol (TCP or UDP). Public Port: Specifies which port should be redirected to the internal host.
Advanced Setup offered by the internal host. Active: Check here to activate the port-mapping entry. Click “OK”. 5.4.2 DMZ Host Setup Click “DMZ Host Setup” to open the setup page. The DMZ Host settings allow a defined internal user to be exposed to the Internet to use some special-purpose applications such as Netmeeting or Internet Games etc. DMZ Enable: Check to enable the DMZ Host function. DMZ Host IP: Enter the IP address of the DMZ host. 5.4.
Advanced Setup 5.5 Static Route Setup Vigor2200 series routers can also be set to operate as pure IP routers. You should specify the IP network configuration for the LAN1 interface using the 2nd IP address and 2nd subnet mask fields on the “LAN1 TCP/IP and DHCP Setup” page, and for the LAN2 interface using “Internet Access Setup” > “Static or Dynamic IP” (See Chapter 3.2 Internet Access Setup). Note: The Vigor2200 series routers have RIP (Routing Information Protocol) built-in by default.
Advanced Setup router supports 10 static route rules for your configurations. Click the numbers in the index to enter the setup page for each rule. The following gives a network example with more detailed descriptions. For example, you have a network 192.168.100.0/24 connected on the LAN1 interface, and 192.168.200.0/24 connected on the LAN2(WAN) interface. Example settings are as follows.
Advanced Setup For LAN1: Click “LAN1 TCP/IP and DHCP Setup” to configure your LAN1 interface for IP routing. Check “Enable” and assign 192.168.100.1 in the 2nd IP Address field, 255.255.255.0 in the 2nd Subnet Mask field. You now have a routeable network 192.168.100.0/24 connected on the LAN1 interface. For LAN2(WAN): To configure the LAN2(WAN), on the Main Setup Menu click “Internet Access Setup” > “Static or Dynamic IP” to enter the setup page.
Advanced Setup addition, we assume another router, 192.168.200.253/24, is also connected to the same Ethernet segment as LAN2(WAN). Behind the router is another IP network, 192.168.202.0/24. The following subsections based on this example give more detailed explanations. 5.5.1 Add a Static Route In the above example, if you want the 192.168.202.0/24 and 192.168.100.0/24 network to have access to each other, you should add a static route in the Vigor2200 router and also in the 192.168.200.253 IP Router.
Advanced Setup the 192.168.202.0 network is behind the router. Network Interface: Specifies the network interface. In the example, we use LAN2 to connect to the next hop router 192.168.200.253. Click “OK”. Note: For the static route to work, the next hop router must also have added a static route to forward all 192.168.100.0/24 IP packets to the Vigor2200 router. After clicking the “OK” button, you will see the added route is shown in the current running routing table. Click “View Routing table” to verify.
Advanced Setup Click “OK”. All items on the above setup page will be cleared and be removed from the routing table. 5.5.3 Deactivate a Preset Static Route Sometimes you may want to deactivate but not clear the preset static route. Set the Status/Action field to Inactive/Disable as shown below. Click “OK” to disable/make the preset static route inactive. 5.6 IP Filter/Firewall Setup The IP Filter/Firewall function helps pretect your local network against attack from outside.
Advanced Setup Filter. The former is designed to block or allow IP packets that will trigger the router to establish an outgoing connection. The latter is designed to block or allow which kind of IP packets are allowed to pass through the router when the WAN connection has been established. In concept, when an outgoing packet is to be routed to the WAN, the IP Filter will decide if the packet should be forwarded to the Call Filter or Data Filter.
Advanced Setup The following sections will explain more about IP Filter/Firewall Setup using the Web Configurator. The Filter has 12 filter sets with 7 filter rules for each set. There are a total of 84 filter rules for the IP Filter/ Firewall Setup. By default, the Call Filter rules are defined in Filter Set 1 and the Data Filter rules are defined in Filter Set 2. General Setup: Some general settings are available from this link. Filter Setup: Here there are 12 filter sets for IP Filter configurations.
Advanced Setup Call Filter: Check “Enable” to activate the Call Filter function. Assign a start filter set for the Call Filter. Data Filter: Check “Enable” to activate the Data Filter function. Assign a start filter set for the Data Filter. Log Flag: For troubleshooting needs you can specify the filter log here. None: The log function is inactive. Block: All blocked packets will be logged. Pass: All passed packets will be logged. No Match: The log function will record all packets which are unmatched.
Advanced Setup Note: The filter log will be displayed on the Telnet terminal when you type the “log -f” command. MAC Adddress for Packet Duplication: Logged packets may also be logged to another location via Ethernet. If you want to duplicate logged packets from the router to another network device, you must enter the other devices’ MAC Address (HEX Format). Type “0” to disable the feature (also see “Duplicate to LAN” on page 5-21). The feature will be helpful under Ethernet environments. 5.6.
Advanced Setup Filter Rule: Click a button numbered “1” ~ “7” to edit the filter rule. Active: Enable or disable the filter rule. Next Filter Set: Specifies the next filter set to be linked behind the current filter set. The filters cannot be looped. The following setup pages show the default settings for the Call Filter and the Data Filter. You will see the Call Filter set is assigned to Set 1 and the Data Filter set to Set 2.
Advanced Setup 5.6.4 Editing the Filter Rules Click the Filter Rule index button to enter the Filter Rule setup page for each filter. The following explains each configurable item in detail. Comments: Enter filter set comments/description. Maximum length is 14 characters. Check to enable the Filter Rule: Enables the filter rule. Pass or Block: Specifies the action to be taken when packets match the rule. Block Immediately: Packets matching the rule will be dropped immediately.
Advanced Setup Pass If No Further Match: A packet matching the rule, and that does not match further rules, will be passed through. Branch to Other Filter Set: If the packet matches the filter rule, the next filter rule will branch to the specified filter set. Duplicate to LAN: If you want to log the matched packets to another network device, check this box to enable it. The MAC Address is defined in “General Setup” > “MAC Address for Logged Packets Duplication” (see page 5-17).
Advanced Setup For the Data Filter: IN: Specifies the rule for filtering incoming packets. OUT: Specifies the rule for filtering outgoing packets. Protocol: Specifies the protocol(s) this filter rule will apply to. IP Address: Specifies a source and destination IP address for this filter rule to apply to. Placing the symbol “!” before a particular IP Address will prevent this rule from being applied to that IP address. It is equal to the logical NOT operator.
Advanced Setup Don’t Care: Specifies no fragment options in the filter rule. Unfragmented: Applies the rule to unfragmented packets. Fragmented: Applies the rule to fragmented packets. Too Short: Applies the rule only to packets which are too short to contain a complete header. 5.6.5 Restricting Unauthorized Internet Services This section will show a simple example to restrict someone from accessing WWW services. In this example, we assume the IP address of the access-restricted user is 192.168.1.10.
6 Virtual TA Application 6.1 Virtual TA Concepts 6.2 Installing a Virtual TA Client 6.
Virtual TA Application Note: Not supported on the Vigor2200E model. This chapter covers Virtual TA concepts and explains how to setup a Virtual TA. Quick Setup > Virtual TA (Remote CAPI) Setup 6.1 Virtual TA Concepts The term Virtual TA means the local Ethernet-connected hosts or PCs use popular CAPI-based software such as RVS-COM or BVRP etc. to access the router as a local ISDN TA for FAX sending or receiving via the ISDN line. Basically, it is a client/server network model.
Virtual TA Application The maximum number of active clients is also 2. 4. Before you set up the Virtual TA, you must set the correct country code. Click “ISDN Setup” in the Basic Setup group. As the following application chart shows, the Virtual TA client can make an outgoing call or accept an incoming call to/from a peer FAX machine or ISDN TA etc. 6.2 Installing a Virtual TA Client 1. Insert the CD-ROM supplied with your Vigor2200, or directly double-click the installer file. Vsetup95.
Virtual TA Application When the icon text is GREEN, the Virtual TA client is connected to the Virtual TA server and you can launch your CAPI-based software to use the client to access the router. Read your software user guide for detailed configuration. If the icon text is RED, it means the client lost the connection with the server. Check the physical Ethernet connection. 6.3 Configuring a Virtual TA Client/Server The Virtual TA application is a client/server model.
Virtual TA Application Virtual TA Server: Enable: Check to activate the server. Disable: Check to deactivate the server. All Virtual TA applications will be stopped. Virtual TA User Profiles: Username: Specifies the username for a specific client. Password: Specifies the password for a specific client. MSN1, MSN2, MSN3: MSN stands for Multiple Subscriber Number. It means you can subscribe to more than one ISDN line number on a single subscribed line.
Virtual TA Application Creating a User Profile Note that creating a single user access account limits access to the Virtual TA server to only the specified account holders. In the following, we assume you have no MSN service from your ISDN network provider. 1. On the server: Click “Virtual TA (Remote CAPI) Setup”, and fill in the Username and Password fields. Check the “Active” checkbox to enable the account. 2. On the client: Right-click the mouse on the VT icon. The following pop-up menu will be shown.
Virtual TA Application 4. Enter the Username and Password and click “OK”. After a short time the VT icon text will become green. Configuring the MSN Number If you have subscribed to an MSN number service, the Virtual TA server can specify which client has the specified MSN number. When an incoming call arrives, the server will alert the Username-Passwordmatched and MSN-matched client. 1. As an example, you could assign the MSN number “123” to the “alan” client. 2.
7 System Management 7.1 Online Status 7.2 Management Setup 7.3 Diagnostic Tools 7.4 Reboot System 7.
System Management This chapter will show you how to manage your router using the System Management tools shown below. System Management > Online Status > Management Setup > Diagnostic Tools > Reboot System > Firmware Upgrade (TFTP Server) 7.1 Online Status Click “Online Status” to open the Online Status page. In the example, on the following page, both the ISDN B1 and B2 channel are active and also a PPPoE connection is up on the LAN2/WAN interface.
System Management The Online Status page contains three subgroups: ISDN Status, LAN1 Status and LAN2/WAN Status. ISDN Status: (Vigor2200 and Vigor2200X Only) Active Connection: The ISP, active remote dial-in user, or LANto-LAN profile name and also the IP address for each B channel. TX Pkts: Total number of transmitted IP packets sent during this connection session. TX Rate: Transmission rate for outgoing data. The unit is characters per second (cps).
System Management Drop B1: Click to disconnect the B1 channel. Drop B2: Click to disconnect the B2 channel. LAN1 Status: IP Address: IP address of the LAN1 interface. TX Packets: Total number of transmitted IP packets sent since the router was powered on. RX Packets: Total number of received IP packets received since the router was powered on. LAN2/WAN Status: Mode: Indicates which broadband access mode is active. Depending upon the broadband access mode, you may see Static IP, Dynamic IP, PPTP, or PPPoE.
System Management 7.2 Management Setup By default, the router may be configured and managed with any Telnet client or Web browser running on any operating system. There is no requirement for additional software or utilities. However, for some specific environments, you may want to change the server port numbers for the built-in Telnet or HTTP server, create access lists to protect the router, or reject system administrator login from the Internet. Click “Management Setup”.
System Management specific host or network defined in the list. A maximum of three IPs/ subnet masks may be entered. IP: Specifies an IP address allowed to login to the router. Subnet Mask: Specifies a subnet mask allowed to login to the router. Port Setup Default Ports: Check to use standard port numbers for the Telnet and HTTP servers. User Defined Ports: Check to specify user-defined port numbers for the Telnet and HTTP servers. 7.
System Management ISDN / PPPoE / PPTP Diagnostics: Click here to open the following page. The page shown here is for reference only; individual networks will show different results. The page has been grouped into two subgroups, the upper is for ISDN link status, the lower is for broadband access status. Refresh: To obtain the latest information, click here to reload the page. ISDN: ISDN Link Status: If the link is active, this field will show UP. Otherwise, it shows DOWN.
System Management Drop B1: Click to disconnect the B1 channel. Drop B2: Click to disconnect the B2 channel. Broadband Access: Broadband Access Mode/Status: Displays the broadband access mode and status. If the broadband connection is active, it will show PPPoE, PPTP, Static IP, or DHCP Client depending on which access mode is enabled. If the connection is idle, it will show “---”. WAN IP Address: The WAN IP address for the active connection.
System Management Refresh: Click to reload the page. View Routing Table: Click View Routing Table to view the router’s routing table. The table provides current IP routing information held in the router. To the left of each routing rule you will see a key. These keys are defined as: C --- Directly connected. S --- Static route. R --- RIP. * --- Default route. To the right of each routing rule you will see an interface identifier: IF0 --- Local LAN interface. IF1 --- ISDN B1 channel.
System Management View ARP Cache Table: Click View ARP Cache Table to view the ARP (Address Resolution Protocol) cache held in the router. The table shows a mapping between an Ethernet hardware address (MAC Address) and an IP address. View DHCP Assigned IP Addresses: View DHCP Assigned IP Addresses provides information on IP address assignments. This information is helpful in diagnosing network problems, such as IP address conflicts, etc.
System Management View NAT Port Redirection Running Table: If you have configured Port Redirection (under NAT Setup), click to verify that your settings are correct for redirecting specific port numbers to specified internal users.
System Management View NAT Active Sessions Table: As the router accesses the Internet through the built-in NAT engine, click View NAT Active Sessions Table to see which active outgoing sessions are online. Each line across the screen indicates an active session. The following information is displayed: Private IP, Port: The internal user’s (PC’s) IP address and port number. #Pseudo Port: The public port number. Peer IP, Port: The peer user’s (PC’s) IP address and port number.
System Management 7.4 Reboot System The Web Configurator may be used to restart your router. Click “Reboot System“ to open the following page. There are two reboot options: Using current configuration and Using factory default configuration. If you want to reboot the router using current running configurations, check Using current configuration and click “OK”. To reset the router’s settings to default values, check Using factory default configuration and click “OK”.
System Management tion. Click Firmware Upgrade (TFTP Server) to open the following screen. Click “OK” to enable the function. 3. Click Start > Programs > Router Tools > Firmware Upgrade Utility to launch the Firmware Upgrade Utility.
System Management The Router IP field will show the IP address of your router. Click “Browse” to select the new firmware file. The file shown here (v2k200001.all) is for example purposes only and the latest firmware will have a different file name. Click “Upgrade”. The upgrade status will be shown on the progress bar.
8 Troubleshooting & FAQ 8.1 Using the Telnet Terminal Commands 8.2 Viewing Call Logs 8.3 Viewing ISDN Logs 8.4 Viewing PPP Logs 8.5 Viewing WAN Logs 8.6 Troubleshooting the DHCP Client on WAN 8.
Troubleshooting & FAQ The following section explains how to use Telnet terminal commands to diagnose your network problems via the built-in debug tool. Our examples use Windows’ Telnet client software. If you are a Mac user, you should install third-party Telnet client software on your computer. By default, Linux has a built-in Telnet client. 8.1 Using the Telnet Terminal Commands Click Start > Run and type “Telnet 192.168.1.1” in the Open box as below.
Troubleshooting & FAQ Command Help: If you are not familiar with these commands, type the command followed by a question mark ?. For example, the ip command is a first level command. Type “ip ?” to get next level commands as shown below. Recall Commands: The Telnet terminal also provides a method to recall the command history. Use the Up and Down arrow keys on your keyboard to recall previous commands. Quitting the Telnet Terminal: Type quit or exit to quit the Telnet terminal.
Troubleshooting & FAQ 8.2 Viewing Call Logs The Call log provides a simple method for troubleshooting call setup or WAN connection problems. By default, the router records WAN connection messages. This information can be helpful in diagnosing WAN connection problems. If you do not understand the content, you can easily save the log and send it to a support technician. The steps are: 1. Login to the Telnet terminal. 2. Type “log -F c” to clear all call logs. 3.
Troubleshooting & FAQ 8.3 Viewing ISDN Logs To capture messages exchanged on the ISDN interface, use the “log -i” command to dump all exchanged messages on the ISDN interface. The steps are: 1. Login to the Telnet terminal. 2. Type “log -F w” to clear all ISDN logs. 3. Ping to any outside host to trigger the router to dial from your PC. 4. Type “log -i” to display the latest ISDN log. To display all ISDN logs saved in the log buffer, type “log -i -t”.
Troubleshooting & FAQ type the log -i -t command. This command allows you to see whether the ISDN connection could be established or not. Note that if you cannot understand the details, save these messages in a file and send it to a support technician. 8.4 Viewing PPP Logs To view PPP logs, type “log -p”. The steps are: 1. Login to the Telnet terminal. 2. Type “log -F w” to clear all PPP logs. 3. Ping to any outside host to trigger the router to dial from your PC. 4.
Troubleshooting & FAQ 8.5 Viewing WAN Logs To view all WAN logs, including ISDN D-channel and PPP/PPPoE/ PPTP messages, the simplest way is to type “log -w -t”. The steps are: 1. Login to the Telnet terminal. 2. Type “log -F w” to clear all PPP/PPPoE/PPTP and ISDN logs. 3. Ping to any outside host to trigger the router to dial from your PC. 4. Type “log -w” to display the latest WAN log. If you want to display all WAN logs, use the “log -w -t” command. 8.
Troubleshooting & FAQ Renewing the IP Address Type “ip dhcpc renew” to get a new IP address from the cable service provider. Viewing the WAN Status Type “ip dhcpc status” to show the status of the DHCP client for the WAN interface. Viewing DHCP Logs In some special cases, you may want to capture the detailed DHCP messages sent between the WAN interface and the cable head-end access server. Type “log -i” to dump these DHCP exchanged messages.
Troubleshooting & FAQ as Obtain an IP address automatically. 8.7 FAQs The following frequently asked questions cover common questions. For more FAQs, visit DrayTek’s website (www.draytek.com) or contact your local technical support. 1. What is the default administrator password to login to the router? A: By default, you don’t need a password to login to the router. For security, you should assign a password to protect your router against hacker attacks. 2. I forgot the administrator password.
Troubleshooting & FAQ 3. What is the default IP address of the router? A: The default IP address is 192.168.1.1 with subnet mask 255.255.255.0. 4. Why does the router dial out very often? A: Examine the packets that trigger the router to dial out. Login to the Web Configurator and click “Diagnostic Tools” > “Triggered Dialout Packet Header”. You will see the triggered packet contents. Report the results to technical support by e-mail or telephone. 5.
Troubleshooting & FAQ 8-11
Technical Specifications LAN2 (WAN) Interface 1. One 10Base-T LAN2 (WAN) port with two RJ-45 connectors (Vigor2200), One 10Base-T WAN port with one RJ-45 port (Vigor2200X, Vigor2200E) 2. P P P oE 3. DHCP Client (Dynamic IP Addressing) 4. PPTP Client 5. Static IP Addressing ISDN Interface (Vigor2200 and Vigor2200X only) 1. One Basic Rate Interface (BRI) 2. S/T Interface 3. Layer-1 conforms to ITU-T I.430 4. D channel signaling protocol complies with DSS1 (European), VN3 (French), BT ISDN2e (British) etc.
