i
Vigor2133 Gigabit Broadband Router Quick Start Guide Version: 1.1 Firmware Version: V3.8.
Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp.
EU Declaration of Conformity We DrayTek Corp. , office at No.26, Fu Shing Road, HuKou County, Hsin-Chu Industry Park, Hsinchu 300, Taiwan , R.O.C., declare under our sole responsibility that the product Product name: Gigabit Broadband Router Model number: Vigor2133 Manufacturer: DrayTek Corp. Address: No.26, Fu Shing Road, HuKou County, Hsin-Chu Industry Park, Hsinchu 300, Taiwan , R.O.C.
Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Be a Registered Owner Web registration is preferred. You can register your Vigor router via http://www.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. http://www.draytek.
Table of Contents 1. Introduction........................................................................................................... 1 2. Package Content .................................................................................................. 2 3. Panel Explanation................................................................................................. 3 4. Hardware Installation ........................................................................................... 5 4.
1. Introduction The Vigor2133 features advanced bandwidth control mechanism such as IP-layer QoS, NAT Session Limitation, Bandwidth Borrowed, etc., to allow easy, flexible, reliable access control and bandwidth management. The SPI (Stateful Packet Inspection) firewall uses object-based design to make settings of firewall policies easy.
2. Package Content Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Vigor Router Quick Start Guide RJ-45 Cat-5 Ethernet Cable The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 17-23 Watt.
3. Panel Explanation LED (Activity) USB WAN ~ LAN1/2/3/4 Status Explanation Blinking Blinking The router is powered on and running normally. When ACT and WLAN LEDs blink quickly and simultaneously is enabled and the system waits for wireless station of connection. The router is powered off. A USB device is connected and active. The data is transmitting. Internet connection is ready. The data is transmitting. Internet connection is not ready.
Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. USB1~USB2 Connector for a USB device (for 3G/4G USB Modem or printer). GigaLAN1~LAN4 Connectors for local networked devices. WAN Connector for remote networked devices.
4. Hardware Installation This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly. 4.1 Network Connection 1. Connect the cable Modem/DSL Modem/Media Converter to any WAN port of router with Ethernet cable (RJ-45). 2. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly. 3.
4.2 Wall-Mounted Installation Vigor2133 has keyhole type mounting slots on the underside. 1. A template is provided on the Vigor2133 packaging box to enable you to space the screws correctly on the wall. 2. Place the template on the wall and drill the holes according to the recommended instruction. 3. Fit screws into the wall using the appropriate type of wall plug. Note 4. The recommended drill diameter shall be 6.5mm (1/4”).
5. Software Configuration To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. 1. Make sure your PC connects to the router correctly. Note 2.
3. Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note 4. The home page will change slightly in accordance with the router you have. Enter the login password on the field of New Password and retype it on the field of Confirm Password. Then click Next to continue.
5. On the next page as shown below, please select the appropriate protocol according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. Then click Next for next step. PPPoE: If you click PPPoE as the protocol, after clicking Next, you will get the following web page. Please manually enter the Username/Password provided by your ISP. Then click Next.
PPTP/L2TP: if you click PPTP/L2TP, you will get the following page. Please type in all the information originally provided by your ISP. Then click Next for next step. Static IP: if you click Static IP, you will get the following page. Please type in the IP address information originally provided by your ISP. Then click Next for next step.
DHCP: if you click DHCP, you will get the following page. Simply click Next to continue. 6. Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary. Click Finish and then restart the router. Afterward, you will enjoy surfing on the Internet. 6. Customer Service If the router cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away.
