Operation Manual

Vigor2133 Series User’s Guide
656
base_size: Available setting is 1000 ~ 1500.
-d [decrease size] Set the MTU size to decrease between detections.
decrease size: Available setting is 1 ~ 100.
-w Specify the WAN interface to be detected.
-c [count] Set the times that you want to send the ping packets out.
count: Available settings are 1 ~ 10. Default value is 3.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> wan detect_mtu -w 1 -i 8.8.8.8 -s 1500 -d 30 -c 10
detecting mtu size:1500!!!
mtu size:1470!!!
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
w
w
a
a
n
n
d
d
e
e
t
t
e
e
c
c
t
t
_
_
m
m
t
t
u
u
6
6
This command allows you to run a WAN MTU Discovery. The user can specify an IPv6 target to
ping and find the suitable MTU size of the WAN interface.
S
S
y
y
n
n
t
t
a
a
x
x
wan detect_mtu6 -i <Host/IP address> -s <mtu_size> -w <1>
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
-I [Host/IP address] Specify the IPv6 target to detect. If can be an IPv4 address or
domain name.
Host/IP address: Type the IP address/domain name of the target.
-s [mtu_size] Set the MTU size base for Discovery.
base_size: Available setting is 1280 ~ 1500.
-w Specify the WAN interface to be detected.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> wan detect_mtu6 -w 2 -i 2404:6800:4008:c06::5e -s 1500
>
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
w
w
l
l
a
a
c
c
l
l
This command allows the user to configure wireless access control settings.
S
S
y
y
n
n
t
t
a
a
x
x
wl acl enable [ssid1 ssid2 ssid3 ssid4]
wl acl disable [ssid1 ssid2 ssid3 ssid4]
wl acl add [MAC] [ssid1 ssid2 ssid3 ssid4] [isolate]
wl acl del [MAC]
wl acl mode [ssid1 ssid2 ssid3 ssid4] [white/black]
wl acl show
wl acl showmode
wl acl clean
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
enable [ssid1 ssid2 ssid3
ssid4]
It means to enable the settings for SSID1, SSID2, SSID3 and SSID4.