i
Vigor2133 Series Gigabit Broadband Router Quick Start Guide (for RF Model) Version: 1.2 Firmware Version: V3.8.
Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp.
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type Vigor2133 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: http://www.draytek.com.tw/ftp/Vigor2133/Document/CE/ Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu County, Taiwan 303 Product: Vigor2133 Series Frequency Information for Europe area: 2.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. More update, please visit www.draytek.com.
Be a Registered Owner Web registration is preferred. You can register your Vigor router via http://www.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. http://www.draytek.
Table of Contents 1. Introduction........................................................................................................... 1 2. Package Content .................................................................................................. 2 3. Panel Explanation................................................................................................. 3 4. Hardware Installation ........................................................................................... 7 4.
1. Introduction The Vigor2133 series features advanced bandwidth control mechanism such as IP-layer QoS, NAT Session Limitation, Bandwidth Borrowed, etc., to allow easy, flexible, reliable access control and bandwidth management. The SPI (Stateful Packet Inspection) firewall uses object-based design to make settings of firewall policies easy.
2. Package Content Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Vigor Router Quick Start Guide RJ-45 Cat-5 Ethernet Cable Antenna (for “n” or “ac” model) The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 17-23 Watt.
3. Panel Explanation LED LED (Activity) USB ~ WLAN WAN Status Explanation Blinking Blinking The router is powered on and running normally. When ACT and WLAN LEDs blink quickly and simultaneously is enabled and the system waits for wireless station of connection. The router is powered off. The phone connected to this port is off-hook. The phone connected to this port is on-hook. A phone call comes. A USB device is connected and active. The data is transmitting. Wireless access point is ready.
On Blinking Off ~ LAN1/2/3/4 On Blinking On Blinking Off The WAN port is connected with Ethernet cable. The data is transmitting through WAN port. The WAN port is disconnected. Internet access via fiber connection is ready. The data is transmitting. The LAN port is connected. The data is transmitting. The LAN port is disconnected.
Connectors Interface Description Wireless LAN ON/OFF/WPS WLAN On - Press the button and release it within 2 seconds. When the wireless function is ready, the green LED will be on. WLAN Off - Press the button and release it within 2 seconds to turn off the WLAN function. When the wireless function is not ready, the LED will be off. WPS - When WPS function is enabled by web user interface, press this button for more than 2 seconds to wait for client’s device making network connection through WPS.
Phone2/Phone1 (for “V” model) Connector of analog phone for VoIP communication. ON/OFF Power Switch. PWR Connector for a power adapter.
4. Hardware Installation This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router (taking Vigor2133n for example), you have to connect your devices correctly. 4.1 Network Connection 1. Connect the cable Modem/DSL Modem/Media Converter to any WAN port of router with Ethernet cable (RJ-45). 2. Connect one port of 4-port switch to your computer with a RJ-45 cable.
4.2 Wall-Mounted Installation Vigor2133 series has keyhole type mounting slots on the underside. 1. A template is provided on the Vigor2133 packaging box to enable you to space the screws correctly on the wall. 2. Place the template on the wall and drill the holes according to the recommended instruction. 3. Fit screws into the wall using the appropriate type of wall plug. Note 4. The recommended drill diameter shall be 6.5mm (1/4”).
5. Software Configuration To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. 1. Make sure your PC connects to the router correctly. Note 2.
3. Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note 4. The home page will change slightly in accordance with the router you have. Enter the login password on the field of New Password and retype it on the field of Confirm Password. Then click Next to continue.
5. On the next page as shown below, please select the appropriate protocol according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. Then click Next for next step. PPPoE: If you click PPPoE as the protocol, after clicking Next, you will get the following web page. Please manually enter the Username/Password provided by your ISP. Then click Next.
PPTP/L2TP: if you click PPTP/L2TP, you will get the following page. Please type in all the information originally provided by your ISP. Then click Next for next step. Static IP: if you click Static IP, you will get the following page. Please type in the IP address information originally provided by your ISP. Then click Next for next step.
DHCP: if you click DHCP, you will get the following page. Simply click Next to continue. 6. Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary. Click Finish and then restart the router. Afterward, you will enjoy surfing on the Internet. 6. Customer Service If the router cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away.
