Quick Start Guide
Table Of Contents
- Version: 1.0 Firmware Version: V3.8.9_RC5
- (For future update, please visit DrayTek web site) Date: September 21, 2018
- Safety Instructions
- 1. Introduction
- Vigor2620 series is a VDSL2 router with multi-subnet for secure and efficient workgroup management. It integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth.
- By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DES, and hardware key hash of SHA-1/MD5, the router increases the performance of VPN greatly and offers several protocols (such as IPSec/PPTP/L2TP).
- The object-based design used in SPI (Stateful Packet Inspection) firewall allows users to set firewall policy with ease. CSM (Content Security Management) provides users control and management in IM (Instant Messenger) and P2P (Peer to Peer) more effi...
- 2. Package Content
- 3. Panel Explanation
- 3.1 Vigor2620
- 3.2 Vigor2620n
- This section will guide you to install the router through hardware connection and configure the router’s settings through web browser.
- Before starting to configure the router, you have to connect your devices correctly.
- 1. Connect the DSL interface to the external ADSL splitter with an ADSL line cable.
- 2. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly.
- 3. Connect one end of the power cord to the power port of this device. Connect the other end to the wall outlet of electricity.
- 4. Power on the router.
- 4.2 Wall-Mounted Installation
- Vigor router has keyhole type mounting slots on the underside.
- 1. A template is provided on the Vigor router packaging box to enable you to space the screws correctly on the wall.
- 2. Place the template on the wall and drill the holes according to the recommended instruction.
- 3. Fit screws into the wall using the appropriate type of wall plug.
- Note The recommended drill diameter shall be 6.5mm (1/4”).
- 4. When you finished about procedure, the router has been mounted on the wall firmly.
- 5. Software Configuration
- To access Internet, please finish basic configuration after completing the hardware installation.
- 5.1 Quick Start Wizard for Network Connection
- The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web User Interface. Make sure your PC connects to the router correctly.
- Open a web browser on your PC and type http://192.168.1.1. A pop-up window will open to ask for username and password. Please type “admin/admin” as the Username/Password and click Login.
- 1. If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is entering login password. After typing the password, please c...
- 2. On the next page, please select the WAN interface that you use. If DSL interface is used, please choose WAN1;
- 3. Click Next to go to the following page.
- 4. Manually enter SIM PIN code and SPM Name provided by your ISP. Then click
- Next for viewing summary of such connection.
- 6. Now, you can enjoy surfing on the Internet.
- 6. Customer Service
Vigor2620n
LED Status Explanation
Off
The router is powered off.
Blinking
The router is powered on and
running normally.
On
The router is ready to access Internet.
Off
The router is not ready to access Internet.
Blinking
Slowly: The DSL connection is
ready. Quickly:
On
Physical line has been connected.
Blinking
The connection is training.
On
The LAN port is connected.
Blinking
The data is transmitting through the LAN
port.
On
(Green)
Vigor device is ready for sending
wireless signal.
Off
No wireless signal is sent out.
Blinking
(Orange)
Blinks with one second cycle for two
minutes. The WPS function is active.
Blinking
(Green)
The data is transmitting via
wireless connection.