Vigor2620PVn series Router Quick Start Guide Version: 1.0 Firmware Version: V3.8.
Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp.
Declaration of Conformity Hereby, DrayTek Corporation declares that the radio equipment type Vigor2620 is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: http://www.draytek.com.tw/ftp/Vigor2620/Document/CE/ Manufacturer: DrayTek Corp. Address: No.
Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Be a Registered Owner Web registration is preferred. You can register your Vigor router via http://www.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. http://www.draytek.
Table of Contents 1. Introduction............................................................................................................1 2. Package Content ...................................................................................................2 3. Panel Explanation ..................................................................................................3 3.1 Vigor2620 ..................................................................................................................
1. Introduction Vigor2620 series is a VDSL2 router with multi-subnet for secure and efficient workgroup management. It integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth. By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DES, and hardware key hash of SHA-1/MD5, the router increases the performance of VPN greatly and offers several protocols (such as IPSec/PPTP/L2TP).
2. Package Content Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately.
RJ-11 to RJ45 Cable (Annex B) RJ-11 to RJ-11 Cable (Annex A) Quick Start Guide The type of the power adapter depends on the country that the router will be installed.
3. Panel Explanation Vigor2620 LED Status Off Blinking On Off Blinking On Blinking On Blinking Explanation The router is powered off. The router is powered on and running normally. The router is ready to access Internet. The router is not ready to access Internet. Slowly: The DSL connection is ready. Quickly: Physical line has been connected. The connection is training. The LAN port is connected. The data is transmitting through the LAN port.
Interface Factory Reset Description Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. DSL Connecter for accessing the Internet. LAN P2-P1 Connecters for local network devices. ON/OFF Power Switch. PWR Connecter for a power adapter.
Vigor2620n LED Status Off Blinking On Off Blinking On Blinking On Blinking On (Green) Off Blinking (Orange) Blinking (Green) Explanation The router is powered off. The router is powered on and running normally. The router is ready to access Internet. The router is not ready to access Internet. Slowly: The DSL connection is ready. Quickly: Physical line has been connected. The connection is training. The LAN port is connected. The data is transmitting through the LAN port.
Interface Wireless LAN ON/OFF/WPS DSL Description Press the button and release it within 2 seconds. When the wireless function is ready, the green LED will be on. Press the button and release it within 2 seconds to turn off the WLAN function. When the wireless function is not ready, the LED will be off. When WPS function is enabled by web user interface, press this button for more than 2 seconds to wait for client’s device making network connection through WPS. Restore the default settings.
4. Hardware Installation This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router, you have to connect your devices correctly.
Network Connection via DSL 1. Connect the DSL interface to the external ADSL splitter with an ADSL line cable. 2. Connect one port of 4-port switch to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly. 3. Connect one end of the power cord to the power port of this device. Connect the other end to the wall outlet of electricity. 4. Power on the router. 5. Check the ACT and ADSL2+, LAN LEDs to assure network connections.
4.2 Wall-Mounted Installation Vigor router has keyhole type mounting slots on the underside. 1. A template is provided on the Vigor router packaging box to enable you to space the screws correctly on the wall. 2. Place the template on the wall and drill the holes according to the recommended instruction. 3. Fit screws into the wall using the appropriate type of wall plug. Note 4. The recommended drill diameter shall be 6.5mm (1/4”).
5. Software Configuration To access Internet, please finish basic configuration after completing the hardware installation. 5.1 Quick Start Wizard for Network Connection The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web User Interface. Make sure your PC connects to the router correctly.
Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note The home page will change slightly in accordance with the router you have. 1. If your router can be under an environment with high speed NAT, the configuration provide here can help you to deploy and use the router quickly. The first screen of Quick Start Wizard is entering login password. After typing the password, please click Next. 2. On the next page, please select the WAN interface that you use.
3. Click Next to go to the following page.
4. Manually enter SIM PIN code and SPM Name provided by your ISP. Then click Next for viewing summary of such connection. 5. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. 6. Now, you can enjoy surfing on the Internet. 6. Customer Service If the router cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@draytek.
