SOLAR POWERED AUTO-VARICOSE WELDING & GRINDING HELMET 19730 C€ instructions accompanying the product ars the original Instructions. This document Is part of the product, k-tin ot e o1 profit passing It on to any subsequent hider of the product Read al these Instructions before assembling, operating or maintaining this product. This manual has bean compiled by Draper Tools describing the surpass for which the product has bean , and contagion all the necessary Information to ensure Its comment and safe use.
1. TITLE PAGE 1.1 INTRODUCTION: USER MANUAL FOR: Solar Powered Auto-Lampshade Welding & Grinding Helmet Stock No: 19730 Part No: WEPT 1.2 REVISIONS: Date first published April 2018. ‘As our user manuals are continually updated, users should make sure that they use the very latest version. Downloads are available from: Draper Tools Limited Hurley Road Chandler's Ford Eightieths Hampshire 8053 1YF UK ‘Website: drapertools.com Product Helpline: +44 (0) 23 8049 4344 General Fax: +44 (0} 23 8026 0784 1.
2. CONTENTS 1. TITLE PAGE 1.1 1.2 REVISION HISTORY . 1.3 UNDERSTANDING THIS MANUAL . 14 COPYRIGHT NOTICE 2. CONTENTS 2.1 CONTENTS 3. GUARANTEE 3.1 4. INTRODUCTION 41 43 HANDLING AND STORAGE 5. HEALTH AND SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR WELDING HELMETS 6. TECHNICAL DESCRIPTION 6.1 IDENTIFICATION 7. UNPACKING AND CHECKING 7.1 PACKAGING 8. PREPARING THE HELMET 8.1 COMFORT AND FIT ADJUSTMENTS . 8.2 BEFORE FIRST USE 83 PRODUCT CHARACTERISTICS 84 DARKER SHADE SELECTION. 8.
3. GUARANTEE 3.1 GUARANTEE Draper tools have been carefully tested and inspected before shipment and are guaranteed to be free from defective materials and workmanship. Should the tool develop a fault, please rectum the complete tel to your nearest distributor or contact: Draper Tools Limited, Chandler's Ford, Castlereagh, Hampshire, SO 1YF. England. Telephone Sales Desk: (023) 8049 4333 or: Product Helpline (023) 8049 4344, A troop of purchase must be provided.
4. INTRODUCTION 4.1 SCOPE Wording helmet with solar powered automatic shading facilities when arc is struck. Also features a dedicated grinding setting. 4.2 SPECIFICATION Stock no . Part no. Permanent protection against UV and IR radiation Viewing area 110 x 80mm Power supply . . Solar coulis plus 2x AAA battery Shades 18EW Response time (Light to dark) (0.4ms) (Dark to light) Short. Lon Sensitivity CONT! ..o Operating temperature Weight (tent) 4.
5. HEALTH AND SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR WELDING HELMETS Severe burns are possible with a damaged lens {(cracks, pits and holes etc.). Do not use damaged lenses. Optical radiation can possibly enter in from behind the helmet from other welders welding in the immediate area. This helmet is not designed for oxyacetylene, laser or very low amperage welding applications.
6. TECHNICAL DESCRIPTION 6.1 IDENTIFICATION (D Outer cover lens. (@ Helmet. (@ Welding/Grinding function selection dial. (@ Angle adjustment. (® Upper head band. (® Filter test button. @ Circumference adjustment. Sensitivity control dial. (8 Head band. (D Inner cover lens.
7. UNPACKING AND CHECKING 7.1 PACKAGING Carefully remove the product from the packaging and examine it for any sign of damage that may have happened during shipping. Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline {the telephone number appears on the Ti tie page) and do not attempt to use the product.
8. PREPARING THE HELMET 8.1 COMFORT AND FIT ADJUSTMENTS -FIG. 1 Push and move strap (8 to obtain correct height. Turn for helmet angle adjustment. Push and turn (@ to vary head size, pull knob again to lock position. Loosen knob to adjust distance from face/eyes. 8.2 BEFORE FIRST USE Tear off the cover lens’ screen film on both sides of the filter cartridge before using the helmet. Adjust and select the desired shade no. according to the type of welding and current of weld to suit your requirements.
8. PREPARING THE HELMET 8.4 DARKER SHADE SELECTION FIG. 2 Select the shade level according to the welding process and the value of welding current by muting the potentiate knob on the left side of the helmet. The shade number can be manually set between DINS to DIN. Select a shade number by turning the shade adjustment knob until the row points to the required setting, see shade guide table below. For protraction during grinding operations, set the selection dial to "grind". 8.5 SENSITIVITY SELECTION FIG.
8. PREPARING THE HELMET 8.7 SHADE GUIDE TABLE: ARC Current (Amperes) 125 175 225 275 350 450 |so 60 | 100 | 150 | 200 | 250 | 300 | 400 | 500 [wow TIG, GNAW MAGOG PAW _8 g9 (10|11 12 13 14 Note: SWAM Shielded Metal Arc Welding. MIG (heavy} MIG on heavy metals. MIG (light) MIG on light alloys. TIG, GNAW Gas Tungsten Arc Welding. SAW Shielded Semi-automatic Arc Welding. PAC Plasma Arc Cutting.
9. MAINTENANCE Regular inspection and cleaning reduces the necessity for maintenance operations and will keep the product In good working condition. If the replacement of the part Is necessary, this has to be done by the manufacturer or his agent In order to avoid a safety hazard. All servicing and maintenance not listed in this manual must be carried out by an approved Draper service agent (see back for contact details).
10. DISPOSAL 10.1 DISPOSAL — At the end of the product’s working lif, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. — Contact your local authority for details of collection schemes in your area. In all circumstances: * Do not dispose of power tools with domestic waste. * Do not incinerate. * Do not abandon in the environment. + Do not dispose of WERE* as unsorted municipal waste.
11. EXPLANATION OF SYMBOLS 11.1 EXPLANATION OF SYMBOLS I E, i Read the instruction manual. WERE — Waste Electrical & Electronic Equipment. Do not disposes of Waste Electrical BN Electronic Equipment in with domestic rubbish.
CONTACTS Draper Tools Limited, Hurley Road, Chandler's Ford, Castlereagh, Hampshire. SO 1YF. UK. Helpline: (023) 8049 4344 Sales Desk: (023) 8049 4333 Internet: drapertools.com E-mail: General Inquiries: {(023) 8026 6355 Service/Warranty Repair Agent: For after sales servicing or warranty repairs, please contact the Draper Tools Helpline for details of an agent in your local area. 'YOUR DRAPER STOCKIST BACKCOMB. ‘Published by Draper Toss Limited.
