SRT
SRT SAFETY Observe the safety regulations in the instruction manual of the Power Tool to be used or connected to this attachment. Also observe any applicable additional safety rules. Read the following safety instructions before attempting to operate this product. PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE. The attention of UK users is drawn to The Provision and Use of Work Equipment Regulations 1998, and any subsequent amendments. General ■ Disconnect power tool, when not in use.
SRT ■ Eye protection. Wear safety goggles, spectacles or visors to protect the eyes from ejected waster particles. ■ Respiratory protection. Wear a face or dust mask, or powered respirator. Dust masks/filters should be changed regularly. ■ Do not switch router on with the cutter touching the workpiece. ■ The direction of routing must always be opposite to the cutter's direction of rotation. ■ After work, release the router plunge and allow spindle to stop rotating before putting machine down.
SRT ELECTRICAL SAFETY Mains Plug Replacement (UK & Ireland only) Never use a light socket. Never connect the live (L) or neutral (N) wires to the earth pin marked E or . Always check the condition of the cable and plug before starting with your work. Should your mains plug need replacing and you are competent to do this, proceed as instructed below. If you are in doubt, contact an authorised Trend repair agent or a qualified electrician.
SRT x4 ITEMS ENCLOSED x2 x1 x2 x1 x1 x1 x1 x1 x4 x1 x4 x1 x4 x4 x2 x2 x4 x2 x4 x1 x1 x1 x1 x1 x3 x1 x1 x1 x1 x2 x1 x1 GUARANTEE x1 x1 x1 x1 x16 x16 -5- x3 x1
SRT DESCRIPTION OF PARTS 1 Table top 2 Legs 3 Insert plate 4 Back fence 5 No-volt release switch 6 Dust spout 7 Side pressure guard 8 9 10 9 8 6 13 12 3 4 Top pressure guard 1 Fence cheek stepper 10 Top guard 11 Mitre fence 12 Lead-on pin 13 Insert ring 14 T-handle hex key 4mm 15 Hex key 3mm 2 7 11 5 15 14 Prior to assembly and adjustment always unplug the router table.
SRT ASSEMBLY Fitting Legs Identify Parts x 16 x 16 -7-
SRT Fitting Switch Requires: No 1 Phillips® Screwdriver (not supplied).
SRT Fitting Scaled Label Apply the labels with the zero lining up with the centre line on the insert plate.
SRT Router Compatibility See machine screw illustrations on opposite page. Three machine screws (F) are supplied as standard with the SRT table Make Router Model Screw x Qty TREND DEWALT DRAPER ELU MAKITA PERLES T3, T5, T5 MK2 DW613, 614, 615 PT1200V MOF96(E) MK2 RP0910, 1110C OF808(E) >1999, OF2-808(E) F F F F F F X X X X X X 2 2 2 2 2 2 The following machines require a machine screw pack accessory ref.
SRT Screw Selection Re-drilling Fixing Plate Only ■ Remove the plastic base of the router. Alternatively a photocopy or an outline of the base can be made of the plastic base instead. ■ Align the centre of the fixing plate to the router base and secure them together. A M4x12mm B M5x10mm D M5x16mm F M6x12mm ■ Using a centre punch, mark the centres of holes. ■ Drill the required hole size with a suitable metal cutting drill bit.
SRT Fitting Dust Spout to Back Fence Identify Parts x4 x4 -12-
SRT Fitting Insert Rings 20mm = = 1 30mm = 40mm 2 = 54mm -13-
SRT A Fitting Top Pressure A x2 A x2 B x1 x2 5mm x1 -14- B
SRT D Fitting Back Fence D D x2 x2 Plastic x2 -15-
SRT A Fitting Top Guard A B A x2 B 10mm max.
SRT Fitting Side Pressure C C C x2 5mm 1 2 Metal x2 30mm -17-
SRT Fitting Mitre Fence -18-
SRT Bench Fixing Fix the router table to the workbench or workboard with eight No.8 x 3/4” pan head screws (not supplied).
SRT Dust Extraction Fitting Hose T30/22 CRT/4 Hose Ref: T30/22 or CRT/4 not included.
SRT OPERATION No-Volt Release Switch 1 Plug machine into socket in no-volt release switch. 2 Put plug of switch into mains supply. 3 Switch on router 4 Press green button to switch on. To switch off press red button. OFF ON Isolate from power supply when making any adjustments.
SRT A A Back Fence Adjustment 1 Adjust back fence position by loosening two knobs (A) and pushing fence forwards or backwards. 2 Lock fence position by tightening the two knobs (A). 3 To adjust fence cheeks loosen four back knobs (B). Slide cheeks in and out to suit cutter. Leave gap of 3mm. 4 Max 86mm B A Lock cheeks by tightening four knobs (B). 3mm max. -22- 3mm max.
SRT Edge Moulding and Grooving 1 Isolate from power source. 2 Fit cutter. 3 Set back fence position. 4 Set top and side pressures. 5 Fit guard. 6 Check all knobs are tight. 7 Plug into power supply. 8 Switch on. 9 Feed right to left. ✓ 10 Switch off.
SRT Stopped Moulding 1 Isolate from power supply. 2 Fit cutter. 3 Set back fence position. Fit some stops to back fence using cramps. 4 Fit guard. 5 Check all knobs are tight 6 Plug into power supply. 7 Switch on. 8 Drop material against infeed stop A and pivot into cutter. B 9 A B A Feed right to left, until reaching outfeed limit stop B. 10 Pivot at outfeed stop. 11 Switch off.
SRT Edge Planing A 1 Isolate from power supply. 2 Fit cutter. 3 Loosen back knobs A and adjust stepper on outfeed cheek to required step in 0.8mm x increments. Lock both knobs A. 4 Adjust back fence position so that cutter edge is flush with outfeed cheek. Lock back fence position. 5 Fit pressures and guards. 6 Plug into power supply. 7 Feed right to left. 8 Switch off. A x = 0.8mm 1.6mm 2.
SRT Mitre Fence 1 Isolate from power supply. 2 Fit cutter. 3 Adjust angle of mitre fence by loosening knob and turning protractor head to line up angle required with arrow. 4 Place component onto mitre fence. 5 Plug into power supply. 6 Feed right to left holding component securely. 7 Switch off.
SRT Lead-on Pin 1 Isolate from power supply. 2 Fit lead-on pin into threaded hole using 4mm hex key. 3 Move back fence back. 4 Fit cutter. 5 Fit top guard. 6 Plug into power supply. 7 Support component onto the lead-on pin and swing into cutter. 8 Mould component. 9 Switch off.
SRT MAINTENANCE The router table has been designed to operate over a long period of time with a minimum of maintenance. Continual satisfactory operation depends upon proper tool care and regular cleaning. ■ Cleaning Keep the grooves clear of sawdust. Regularly clean the table with a soft cloth. ■ Lubrication Your router table requires no additional lubrication. RECYCLING Router table, accessories and packaging should be sorted for environmentally friendly recycling.
SRT SRT - SPARE PARTS LIST No. Qty. 1 2 v3.0 07/2003 Desc. Ref.
SRT SRT - SPARE PARTS LIST v3.0 07/2003 No. Qty. Desc. Ref.
SRT SRT - SPARE PARTS DIAGRAM 46 V3.
MANU/SRT v3.0 RECYCLABLE Trend Machinery & Cutting Tools Ltd. Odhams Trading Estate St Albans Road Watford WD24 7TR England Enquiries: _________________0800 487363 Technical Support: ___0044 (0) 1923 224681 Fax: _______________0044 (0) 1923 236879 Email: ___________mailserver@trendm.co.uk Web: ___________www.trendmachinery.co.uk © Copyright Trend 2003. No part of this publication may be reproduced, stored or transmitted in any form without prior permission.
