5 SPEED BENCH DRILL PRESS ■ MODEL No.D13/5A ■ STOCK No. 33662 • INSTRUCTIONS • IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL. 09/2001 GENERAL INFORMATION This manual has been compiled by Draper Tools and is an integrated part of the power tool equipment, which should be kept with the machine. This manual describes the purpose for which this tool has been designed and contains all the necessary information to ensure its correct and safe use.
BENCH DRILL PRESS ■ PART No.D13/5A. ■ STOCK No.33662. CONTENTS: Page Nos. Specification/Guarantee ....................................................................................................................... 3 Unpacking/Checking Contents............................................................................................................. 4 Power Supply ........................................................................................................................................
SPECIFICATION Whilst every effort has been made to ensure accuracy of information given in this manual is correct at the time of going to print, the Draper Tools policy of continuous improvement determines the right to change specification without notice. MODEL No. ................................................................................................................................. D13/5A STOCK No.....................................................................................................
UNPACKING AND CHECKING CONTENTS Carefully unpack the bench drill and all the loose items from the carton. Fig.1. illustrates the bench drill and all the loose items packed in the carton. NOTE: some loose parts are packed inside the pulley cover. Now, referring to Fig.1. carefully check that all the parts are present. Please contact the stockist where your purchase was made if you have any enquiries, eg.
POWER SUPPLY CONNECTING YOUR MACHINE TO THE POWER SUPPLY: To eliminate the possibility of an electric shock your machine has been fitted with a BS approved, non rewireable moulded plug and cable which incorporates a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced an approved BS1362 fuse must be used of the same rating, marked thus . The fuse cover is detachable, never use the plug with the cover omitted.
GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS WARNING Please read the following instructions carefully, failure to do so could lead to serious personal injury. IMPORTANT Draper Tools Limited recommends that this machine should not be modified or used for any application other than that for which it was designed. If you are unsure of its relative applications do not hesitate to contact us in writing and we will advise you. 1.
ADDITIONAL SAFETY RULES FOR DRILL PRESSES 1. This drill press is intended for use only with drill bits. The use of any other accessories may be hazardous. 6. CAUTION. When practical, use a vice or clamps to secure workpiece to avoid workpiece rotating with the drill bit. 2. CHECK to see that the drill bit is securely locked in the chuck. 7. SECURE the tool to a workbench of floor.
KNOW YOUR BENCH DRILL B C D L A E M G F H J I K N A B C D E F G H MOTOR PULLEY COVER MOTOR PULLEY SPINDLE PULLEY SPECIFICATION LABEL DOWN FEED ASSEMBLY CHUCK GUARD CHUCK I J K L M N -8- TABLE COLUMN BASE ON/OFF SWITCH DRIVE BELT/TENSION ADJUSTER MOULDED PLUG AND CABLE
ASSEMBLY 1. Locate the column A base B and three mounting bolts C (Fig.1.) from the loose parts. Fig.1. A C B 2. Secure the column A to the base three bolts C as shown in Fig.2. B using the Fig.2.
ASSEMBLY Cont'd 3. Assemble the table handle E Fig.3. D and table locking Fig.3. D E 4. Slide the table D over the drill press column A and fasten in place by tightening table locking handle E as shown in Fig.4. Fig.4. A D E 5. Carefully put the head assembly F on column A and slide it into position. Align head with table and base and tighten the two hexagon head locking screws G as shown in Fig.5. Fig.5.
ASSEMBLY Cont'd 6. Screw the three downfeed handles H into the three holes located in the pinion shaft, as shown in Fig.6. Fig.6. H 7. From the loose parts locate the chuck guard and depth setting rod P . Loosen screw Q . Fig.7. O Fig.7. Q P O 8. Now slide the chuck guard onto the collar as shown in Fig.8. Secure by tightening screw Q . Fig.8. Q 9. Remove nut R Fig.9. from the depth stop. Fig.9. R 10. Now carefully slide the depth stop rod P Fig.10.
ASSEMBLY Cont'd 11. Make sure the taper of the spindle K Fig.12. and the tapered hole in the chuck L are clean. Push the chuck L up onto the spindle K as far as it will go. Fig.12. K L 12. Open the chuck jaws as wide as possible by turning the chuck sleeve M Fig.13., to make sure that jaws do not protrude. Fig.13. 13. Hold chuck M onto the taper of the spindle and tap with soft faced hammer N to the seat chuck, as shown in Fig.13. M 14. The drill press is supplied with the belt installed.
SPEED/BELT CHANGING SPINDLE SPEEDS Five spindle speeds of 550-2500r.p.m. are available with your drill press. The highest speed is obtained when the belt is on the largest step of the motor pulley and the smallest step of the spindle pulley as shown in Fig.14. Fig.14. SPINDLE MOTOR FAST SLOW CHANGING SPEEDS AND ADJUSTING BELT TENSION 1. Disconnect the drill press from the power supply. 2. Remove the pulley cover locking screw A Fig.15. and open the pulley cover. Fig.15. A B 3.
TABLE ADJUSTMENT 1. The table G Fig.17. can be raised or lowered on the drill press column by loosening the table clamp handle A Fig.17. Move the table to the desired position on the column and tighten table clamp handle A . Fig.17. A G 2. The table can be tilted right or left by loosening the table locking bolt B Fig.18. Fig.18. B 3. Tilt table to the desired angle and tighten bolt B Fig.19. Fig.19. B 4. A tilt scale guide E Fig.20.
SPINDLE RETURN SPRING ADJUSTMENT ADJUSTING SPINDLE RETURN SPRING For the purpose of automatically returning the spindle upward after a hole has been drilled, a spindle return spring is provided in the spring housing A Fig.21. This spring has been properly adjusted at the factory and should not be disturbed unless absolutely necessary. To adjust the return spring, proceed as follows: 1. Disconnect the drill press from the power supply. 2. Loosen the two nuts B approximately ¹⁄₄".
DEPTH SETTING Cont'd 2. All holes will then be drilled to the same depth when the stop nuts A contact the depth stop B as shown in Fig.24. A Fig.24. B OPERATION The following directions will give the inexperienced operator a start on common drill press operations. Use scrap material for practice to get the feel of the machine before attempting regular work.
TROUBLE SHOOTING WARNING: FOR YOUR SAFETY ALWAYS TURN THE MAIN SWITCH ON THE MACHINE"OFF" AND REMOVE THE PLUG FROM THE POWER SUPPLY BEFORE CARRYING OUT ANY MAINTENANCE OR TROUBLE SHOOTING. TROUBLE PROBABLE CAUSE REMEDY Noisy operation 1. Incorrect belt tension 2. Dry spindle 3. Loose spindle pulley or motor pulley 1. Adjust tension 2. Lubricate spindle with grease (ISO VG68) 3. Tighten set screws in pulleys Bit burns or smokes 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6.
OPTIONAL ACCESSORIES The following accessories are available from your local Draper Power stockist: DPV DRILL PRESS VICES Manufactured from cast iron with fully hardened jaws. Carton packed. Stock No. Jaw-mm Width Jaw-mm Opening 54634 54635 54636 54637 75mm 100mm 120mm 145mm 80mm 90mm 118mm 140mm Drill Bit accesoiries are available in the Draper Catalogue.
NOTES - 19 -
DRAPER TOOLS LIMITED, Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. U.K. Helpline: (023) 8049 4344. Sales Desk: (023) 8049 4333. General Enquiries: (023) 8026 6355. Fax: (023) 8026 0784. www.draper.co.uk e-mail: sales@draper.co.uk YOUR DRAPER STOCKIST ©Published by Draper Tools Ltd.