PASSIVE INFRA RED (PIR) DETECTION ALARM WITH REMOTE CONTROL STOCK No.59319 PART No.AL8 • INSTRUCTIONS• IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND EFFECTIVE USE OF THIS TOOL.
FEATURES Your passive infra red sensor alarm with keyring type remote control offers you the protection of professional alarm security that you can install yourself in minutes. It uses a passive infra red (PIR) motion sensor to detect intruders and activate a built-in alarm siren. To arm or disarm the sensor alarm, you simply press “ON” (‘alarm’) on your hand held unit. The sensor alarm’s features include: Compact and Portable – Makes the alarm easy to install just about anywhere.
PARTS IDENTIFICATION 1. 2. 3. 4. 5. 6. 7. 8. 9 10. 11. 12. 13. Motion sensor. Infra-red Remote Receiver. Low Battery Indicator. Siren. External AC Adaptor Socket. External Siren Socket. Battery Compartment. ON (Alarm). Infra-red Remote LED. OFF (Alarm). Battery Compartment. Programmable Security Code Switch. Battery Cover.
PREPARATION INSTALLING BATTERIES 1. Remove the screw at the base of the alarm unit and lift from the bottom of the back cover. 2. Place (4) AA alkaline batteries following the polarity symbols (+ and –) marked inside the battery compartment. 3. Replace the alarm unit into the back cover. NOTES: • The alarm is disarmed after batteries are installed. • The unit will beep and the “BATT LOW” indicator lights when the batteries become weak and need replacing.
PREPARATION Cont’d. SETTING THE SECURITY CODE A programmable 4-position security code switch is builtin the alarm unit and the remote control to prevent other transmitters or radio devices from sounding the unit. Each unit is factory preset. To change The Factory Preset Code On The Sensor Alarm Unit: 1. Locate programmable switch inside the battery compartment. 2. Set the desired switch position. 3. Replace the alarm unit into the back cover. To Change The Factory Preset Code On The Remote Unit: 1.
INSTALLATION The sensor alarm is designed to be either mounted on a wall or free standing placed on a flat surface – desk, shelf, cabinet, etc. When selecting the location for the sensor alarm, keep in mind that the Passive Infra red Sensor is triggered by heat and motion.
OPERATION ARMING ALARM When leaving the protective area, point the remote control at the sensor alarm and press the ON (alarm) button. There will be a short beep, followed by a 30 second delay before the unit is armed. The exit delay allows you time to leave the protected area without activating the alarm. DISARMING ALARM When returning to the protected area, point the remote control at the sensor alarm and press the OFF (alarm) button.
OPTIONAL ACCESSORIES KEYCHAIN REMOTE CONTROLS Get one for every family member! The optional Keychain Remote Control provides every family member with access to the sensor alarm. AC ADAPTOR To prolong battery life,an optional AC Power Adaptor may be used to power the alarm.Simply plug it into the AC Adaptor Socket (see ‘Parts Identification’on Page 2),and feed the cable through the notch in the bottom of the back cover as the alarm unit is snapped into place.
CAUTION The alarm siren is very loud. For your safety, never place the unit close to your ears or let it sound for long lengths of time. BATTERY PRECAUTIONS • Use only new batteries of the required size and recommended type. • Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities. • Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
NOTES -9-
NOTES - 10 -
DRAPER TOOLS LIMITED, Hursley Road, Chandler's Ford, Eastleigh, Hants. SO53 1YF. England. Helpline: (023) 8049 4344. Sales Desk: (023) 8049 4333. General Enquiries: (023) 8026 6355. Fax: (023) 8026 0784. www.draper.co.uk e-mail: sales@draper.co.uk YOUR DRAPER STOCKIST © Published by Draper Tools Ltd.
