Programming instructions

ManualsBrandsDraper ManualsWelding System24v

Adjust Limits in User Mode

If your initial limits have changed or you want to ﬁne tune a motor, you do

not need to reset the motor and re-program it. You can just change the limits

with these steps.

1 Move the motor to the limit (upper or lower) that you want to change.

2 Press and hold the UP and DOWN buttons until the motor jogs.

3 Move the motor to its new limit location.

4 Press and hold the STOP button until the shade jogs.

Fascia for Battery and 24 Volt Dual Roller FlexShade by Draper

Page 2 of 3

www

.draperinc.com

(765) 987-799

Programming Instructions for Battery Motors

Please Note: The motor has no programming on it so it must be learned

and programmed to work on the transmitter that you have at the job.

Here are the initial programming instructions.

1 Connect the battery wand to one motor. Select the transmitter/channel to

which you plan to learn the motor. Press and hold the UP and DOWN

buttons at the same time until the motor jogs, then release.

2 Check the motor run direction by pressing either the UP or DOWN buttons.

This is important because if you do step 3 without doing this step, then you

will need to reset the motor. If you need to

reverse the motor direction, then press the

STOP button (middle button which might

be labeled MY) for ﬁve seconds until the

motor jogs. Check the direction again to

make sure that it works.

3 Move the motor to its upper limit position.

Press the STOP and DOWN buttons at the same time until the motor starts

to move down, then release. You will stop the motor at its lower limit.

You can use the UP and DOWN buttons to adjust the motor to the correct

lower limit position if need be.

4 Once the motor is at its lower limit position, then press the UP and STOP

buttons at the same time until the motor starts to move up, then release.

The motor should move to the upper limit position in step 3 and stop.

5 Once the motor has stopped at its upper limit position, then press and hold

the STOP button for ﬁve seconds until the motor jogs.

6 Now, you must put the motor into USER mode. Find the programming

button which is a small button on the back or side of the transmitter and

press it until the motor jogs. Once you have done this, then the motor will

operate in normal fashion.

7 Disconnect power to this motor and move to the next in your installation

and start with step 1. Reconnect motor to power when all motors are

programmed.

Reset Motor Instructions

If the motor is not working or responding correctly

and you want to reprogram it from the beginning

and clear all previous programming, then follow this.

1 Using a paperclip, press and hold the program

button on the motor head for 12 seconds.

This erases all transmitters and limits.

Setting an Intermediate Stop

Once the shade is in USER mode from the initial programming at top.

1 Move the motor to the mid-point location that you want the stop located.

2 Press and hold the STOP button until the motor jogs.

3 Now, if you hit the STOP button when the motor is standing still, it will move

to that intermediate location.

4 If you want to delete the stop, then go to the intermediate stop and press

and hold the STOP button until the motor jogs.

Add/Delete a Channel/Transmitter

1 Select the channel/transmitter that is currently operating the motor, then

press the programming button until the motor jogs.

2 Select the new channel/transmitter that you want to add to the motor, then

press the programming button until the motor jogs.

3 The motor should now work on both the old and new channel/transmitter.

To delete a channel/transmitter:

1 Select the channel/transmitter that is currently operating the motor and you

want to keep, then press and hold the programming button until the motor

jogs.

2 Select the channel/transmitter that you want to remove, then press and

hold the programming button until the motor jogs.

3 The motor should now only work on the channel/transmitter on step 1.

Please Note: For instructions with Programmable Timer,

please consult instructions provided with the timer.

Channel selector

button on

Multi-Channel

Transmitter

Please Note: When you receive a radio frequency remote control motor

from Draper, Inc., the motor has no programming on it so it must be

learned and programmed to work on the transmitter that you have at the

job. Here are the initial programming instructions.

1 Connect power to one motor. Select the transmitter/channel to which you

plan to learn the motor. Press and hold the UP and DOWN buttons at the

same time until the motor jogs, then release.

2 Check the motor run direction by pressing either the UP or DOWN buttons.

This is important because if you do step 3 without doing this step, then you

will need to reset the motor. If you need to

reverse the motor direction, then press the

STOP button (middle button which might be

labeled MY) for ﬁve seconds until the motor

jogs. Check the direction again to make

sure that it works.