AGES USER MANUAL Dragon Touch DK01 Mini Drone V1.0 Please read this manual before operating your drone, and keep it for further reference.
CONTENTS Package Contents 1 Product Specifications 2 Product Features 2 Getting Started 4 Flight Operation 6 Flight with the Standard Remote Controls 6 Directions 8 Flight With the Gravity Sensor Remote Control 11 Flight With the Waterdrop Remote Control 15 Maintenance 17 Safety Guidance 17 Caution 18 Troubleshooting Guidance 18 Contact Us 19
PACKAGE CONTENTS DK01 Mini Drone × 1 PRODUCT SPECIFICATIONS Standard Remote Control × 1 Gravity Sensor Remote Control x1 Drone Dimensions: 170mm x 170mm x 38mm Battery capacity: 3.7V/500mAh Charging time: 60 minutes Flight time: 6 minutes Remote distance: 60 meters Gravity Sensor Remote Control Battery capacity: 3.
Standard Remote Control GETTING STARTED Charging and installing the battery 1. Charge the drone battery. Power switch High/Low speed switch 3D Flip One key take-off/ Infrared obstacle avoidance Forward fine-tuning Left joystick Right joystick Backward fine-tuning Headless mode Leftward fine-tuning One key return Rightward fine-tuning 5V/1A or 5V/2A Charging: red LED Fully charged: green LED One key landing Long press to activate emergency stop 2. Install the drone battery when fully charged.
6. The battery of the waterdrop remote control is not rechargeable. Note: • For your safety, please use the original battery and USB cables provided. • The battery life will be reduced when it is used in cold weather. • Please avoid exposing the battery to sunlight, heat or high temperatures. 3. Charge the gravity sensor remote control. 5V/1A or 5V/2A FLIGHT OPERATION Charging: red LED Fully charged: green LED 4. Wear the gravity sensor remote control on your palm when fully charged.
2. Calibrate Simultaneously move the left joystick to the bottom right at a 45° angle and move the right joystick to the bottom left at a 45° angle and hold for 3 seconds to calibrate the drone. The LED lights on the drone will blink white for about 3 seconds. The calibration is complete when the colorful LED lights turn on, and you will hear a beep from the remote control.
Leftward and rightward: Pull the Right joystick leftward and the drone will fly leftward; pull it rightward and the drone will fly rightward. 360° Flip After flying the drone to an altitude of over 2 meters, press the Right joystick and 360° Flip button to activate 360° Flip function. Release once the flip is completed. Move the Right joystick forward/backward/leftward/rightward to flip the drone 360° in the corresponding direction.
Headless mode Press the Headless mode button to activate the function. The LEDs on the drone will flash and users will hear a beeping sound from the remote. In this mode, the drone will fly following the direction of the Right joystick regardless of the position of your drone’s head or tail. Press the same button again to exit this mode. Infrared obstacle avoidance Press down the One key take-off/Infrared obstacle avoidance button to activate the Infrared obstacle avoidance mode.
Directions Forward: Release the Finger button during the flight, then tilt your fist downward. Backward: Release the Finger button during the flight, then tilt your fist upward. Rotate left: Press and hold the Finger button during the flight, then lean your fist leftward. Rotate right: Press and hold the Finger button during the flight, then lean your fist rightward. Leftward: Release the Finger button during the flight, then lean your fist leftward.
Infrared obstacle avoidance Continuously press the Finger button 3 times to activate infrared obstacle avoidance mode during the flight. The LEDs on the drone will flash 3 times, then remain on constantly. The drone will fly in another direction when it detects an obstacle. Continuously press the Finger button 3 times again to exit the mode. Emergency stop Press and hold the Power button on the remote for 2 seconds, the drone will stop flying and fall to the ground.
Directions Ascend: Put your hand under the drone. Descend: When the drone flies over an altitude of 1.2 meters, it will slowly descend automatically. Leftward: Put your hand to the right side of the drone. Rightward: Put your hand to the left side of the drone. Landing Press the button on the remote to land the drone during the flight. MAINTENANCE 1. Frequently clean this product with a soft clean cloth. 2. Avoid exposing this product to sunlight, heat or high temperatures. 3. Keep away from water. 4.
5. The drone will fly beyond the control range. • Activate the Headless mode, then move the Right joystick to fly the drone back. 6. The rotor blades need to be replaced. • The propellers and motors are marked A and B. Please pair them when replacing the rotor blades. 7. The waterdrop remote control does not work. • Make sure you turn off the gravity sensor remote and the standard remote.
