Draco vario DVI 474 Series KVM Extender User Manual Edition: 2014-11-11 IHSE GmbH Maybachstraße 11 88094 Oberteuringen Germany info@ihse.com www.ihse.
Draco vario DVI KVM Extender Copyright © 2014. All rights reserved. This information may not be reproduced in any manner without the prior written consent of the manufacturer. Information in this document is subject to change without notice. Trademarks All trademark and trade names mentioned in this document are acknowledged to be the property of their respective owners.
Contents Contents 1 About This Manual ....................................................................... 7 1.1 Scope.................................................................................. 7 1.2 Validity ................................................................................ 7 1.3 Cautions and Notes ............................................................ 7 2 Safety Instructions ....................................................................... 8 3 Description ...
Draco vario DVI KVM Extender 3.7 4 4 3.6.13 Model L- / R474-BSHSV / -BSHXV ..................... 25 3.6.14 Model L- / R474-BXH .......................................... 26 3.6.15 Model L- / R474-BXE .......................................... 26 3.6.16 Model L- / R474-BUE .......................................... 26 3.6.17 Model L- / R474-BAX / -BSX............................... 27 3.6.18 Model L- / R474-BAP .......................................... 27 3.6.19 Model L- / R474-BXP ........
Contents 4.5 5 Overview Upgrade Modules.............................................. 47 Configuration.............................................................................. 48 5.1 Transmission Parameters ................................................. 48 5.2 DDC Settings .................................................................... 48 5.3 Command Mode ............................................................... 49 5.4 USB-HID Ghosting ............................................
Draco vario DVI KVM Extender 7.4 8 9 10 11 Connector Pinouts ............................................................ 67 7.5 Power Supply.................................................................... 72 7.6 Environmental Conditions ................................................. 73 7.7 Size ................................................................................... 74 7.8 Shipping Weight ................................................................ 75 Troubleshooting ...
About This Manual 1 About This Manual 1.1 Scope This manual describes how to install your KVM Extender, how to operate it and how to perform trouble shooting. 1.2 Validity This manual is valid for all devices listed on the front page. The product code is printed on the base of the devices. 1.
Draco vario DVI KVM Extender 2 Safety Instructions To ensure reliable and safe long-term operation of your KVM Extender please note the following guidelines: Installation Only use in dry, indoor environments. The KVM Extender and the power supply units can get warm. Do not install components in an enclosed space without any airflow. Do not place the power supply directly on top of the device. Do not obscure ventilation holes.
Description 3 Description Pos: 4 /806-IHSE/Beschreibung/Verwendungszweck/474-xx @ 6\mod_1304579672848_6.doc @ 50785 @ 2 @ 1 3.1 Application The KVM Extender is used to increase the distance between a source (computer, CPU) and its console (keyboard, mouse, and other peripheral devices). The KVM Extender is designed for use with Cat X (Twisted Pair) interconnect cables or fiber interconnect cables.
Draco vario DVI KVM Extender 3.2 System Overview The KVM Extender consists of at least one CPU module and one CON module. The various modules are summarized respectively in a vario chassis (2-fold, 4-fold or 6-fold) at CPU site and CON site (CPU and CON Unit). The CPU module is connected directly to the source (computer, CPU) using the supplied cables. The CON module is connected to the console (monitor, keyboard and mouse).
Description 3.3 Product Range 3.3.1 Part Numbers Part numbers for Connections via Cat X or Fiber Cable All devices are available in the following versions: Connection via Cat X cable (x = "C") Connection via Single-mode fiber cable (x = "S") High speed connection (3.125 Gbit/s) via Single-mode fiber cable (x = "X") Fiber devices can be used with Multi-mode and Single-mode cables (see Chapter 7.2.2, Page 65).
Draco vario DVI KVM Extender 3.3.
Description 3.3.4 Upgrade Modules Model L474-BXH R474-BXH L474-BXE R474-BXE L474-BAX R474-BAX L474-BAP R474-BAP L474-BSX R474-BSX L474-BXP R474-BXP L474-BDX R474-BDX L474-BAH R474-BAH L474-BUE R474-BUE L474-BAE R474-BAE L474-BDH R474-BDH L474-BDE R474-BDE L474-BDD R474-BDD L474-BDA R474-BDA L474-BXTx R474-BXTx 2014-11-11 Description Upgrade module with 2x USB-HID Upgrade module with 2x USB 2.
Draco vario DVI KVM Extender 3.3.
Description 3.
Draco vario DVI KVM Extender 3.5 Accessories Model Description 026-2A Serial cable 1.8 m (RS232) 247-U1 USB cable 1.8 m (Type A to B) 260-5G International power supply unit 100...240VAC / 5VDC / 3 A 260-5U International power supply unit 100...240VAC / 5VDC / 4 A 436-AA VGA cable 1.8 m (VGA to DVI-I) 436-ID DVI-D cable 1.8 m (DVI-D) 445-2H DVI-D splitter cable 455-CK Stereo jack cable 1.6 m (3.5 mm Stereo) 455-CR RCA cable 2.5 m (Cinch male connector) 455-CT TOSLINK cable 1.
Description 3.6.2 2-fold Vario Chassis 474-BODY2N CPU and CON Unit 4 3 1 2 Rear View 1 Slot for modules #1 2 Connect to power supply (standard) 3 Slot for modules #2 4 Connect to 5VDC power supply (redundancy) The 2-fold vario chassis with an internal power supply is not equipped with a fuse on its primary side. Therefore the protection against excessive currents has to be provided by the electrical installation of the building. Pos: 13 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.
Draco vario DVI KVM Extender Pos: 14 /806-IHSE/Beschreibung/Geräteansichten/474-xx/4-fach Vario-Gehäuse 474-BODY4/4 R @ 6\mod_1304580359098_6.doc @ 50876 @ 3 @ 1 3.6.3 4-fold Vario Chassis 474-BODY4/4R CPU and CON Unit 4 5 6 1 2 3 Rear View 1 Slot for modules #3 2 Slot for modules #1 3 Connect to 5VDC power supply (standard) 4 Slot for modules #4 5 Slot for modules #2 6 Connect to 5VDC power supply (redundancy, optional) For operation with three KVM Extender CON modules and a USB 2.
Description Pos: 16 /806-IHSE/Beschreibung/Geräteansichten/474-xx/6-fach Vario-Gehäuse 474-BODY6R @ 6\mod_1304580442488_6.doc @ 50894 @ 3 @ 1 3.6.
Draco vario DVI KVM Extender 3.6.5 6-fold Vario Chassis 474-BODY6BP CPU and CON Unit 1 2 3 Front View 1 Connect to power supply 1 2 Connect to power supply 2 (redundancy) 3 Grounding 4 5 6 1 2 3 Rear View 1 Slot for modules #5 2 Slot for modules #3 3 Slot for modules #1 4 Slot for modules #6 5 Slot for modules #4 6 Slot for modules #2 Pos: 18 /806-IHSE/Beschreibung/Geräteansichten/474-xx/6-fach Vario-Gehäuse 474-BODY6BPF @ 11\mod_1392644763729_6.
Description 3.6.6 6-fold Vario Chassis 474-BODY6BPF CPU and CON Unit 6 7 8 1 2 3 4 5 Rear View 1 Slot for modules #5 2 Slot for modules #3 3 Slot for modules #1 4 Connect to power supply 1 5 Connect to power supply 2 (redundancy) 6 Slot for modules #6 7 Slot for modules #4 8 Slot for modules #2 Pos: 19 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.
Draco vario DVI KVM Extender Pos: 20 /806-IHSE/Beschreibung/Geräteansichten/474-xx/21-fach Vario-Gehäuse 474-BODY21R @ 8\mod_1348579151346_6.doc @ 69400 @ 3 @ 1 3.6.7 21-fold Vario Chassis 474-BODY21R CPU and CON Unit 1 Rear View 1 Slots for modules #1 - #21 1 2 3 4 Front View 1 Connect to power supply 2 2 Locking for power supply 2 (redundancy) 3 Locking for power supply 1 (standard) 4 Connect to power supply 1 Pos: 21 /806-IHSE/zz_Layout/Seitenumbruch @ 8\mod_1348581820516_0.
Description Pos: 22 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BSHC / -BVHC @ 6\mod_1304580479441_6.doc @ 50912 @ 3 @ 1 3.6.
Draco vario DVI KVM Extender Pos: 25 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BSHCR / -BVHCR @ 9\mod_1362471988604_6.doc @ 71210 @ 3 @ 1 3.6.
Description 3.6.
Draco vario DVI KVM Extender 3.6.14 Model L- / R474-BXH CPU Module CON Module 1 1 Rear View Rear View 1 1 To CPU: USB-HID Connect to USB-HID devices Pos: 30 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BXE @ 7\mod_1331798896275_6.doc @ 58110 @ 3 @ 1 3.6.15 Model L- / R474-BXE CPU Module CON Module 1 1 Rear View Rear View 1 1 To CPU: USB 2.0 Connect to USB 2.0 devices Pos: 31 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BUE @ 7\mod_1331799038717_6.
Description 3.6.17 Model L- / R474-BAX / -BSX CPU Module 1 CON Module 2 3 1 2 3 Rear View Rear View 1 Connect to serial (D-Sub 9) 1 Connect to serial (D-Sub 9) 2 Audio IN 2 Audio IN 3 Audio OUT 3 Audio OUT Pos: 33 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BAP @ 9\mod_1362472648439_6.doc @ 71250 @ 3 @ 1 3.6.
Draco vario DVI KVM Extender 3.6.19 Model L- / R474-BXP CPU Module CON Module 1 2 3 1 4 Rear View Rear View 1 Connect to local PS/2 mouse 1 2 Connect to local PS/2 keyboard 2 3 To CPU: PS/2 mouse 4 To CPU: PS/2 keyboard 2 Connect to PS/2 mouse Connect to PS/2 keyboard The upgrade module L- / R474-BXP is only available in combination with the upgrade modules L- / R474-BAX and –BAH. A separate slot is required for each module.
Description Pos: 36 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BDX @ 6\mod_1304583577801_6.doc @ 51020 @ 3 @ 1 3.6.20 Model L- / R474-BDX CPU Module 1 2 CON Module 1 3 3 2 Rear View Rear View 1 S/PDIF input (RCA) 1 S/PDIF output (RCA) 2 AES/EBU input (Mini-XLR) 2 AES/EBU output (Mini-XLR) 3 S/PDIF input (TOSLINK) 3 S/PDIF output (TOSLINK) Pos: 37 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BAH @ 6\mod_1304583611785_6.doc @ 51038 @ 3 @ 1 3.6.
Draco vario DVI KVM Extender 3.6.23 Model L- / R474-BAE CPU Module 1 CON Module 2 3 4 1 4 2 3 Rear View Rear View 1 Connect to serial (D-Sub 9) 1 Connect to serial (D-Sub 9) 2 Audio IN 2 Audio IN 3 Audio OUT 3 Audio OUT 4 To CPU: USB 2.0 4 Connect to USB 2.0 devices Pos: 40 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BDE @ 8\mod_1348580272466_6.doc @ 69440 @ 3 @ 1 3.6.
Description Pos: 42 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BDD @ 6\mod_1304583696426_6.doc @ 51074 @ 3 @ 1 3.6.
Draco vario DVI KVM Extender Pos: 45 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BXTC @ 6\mod_1304583784582_6.doc @ 51110 @ 3 @ 1 3.6.27 Model L- / R474-BXTC CPU Module 1 CON Module 3 2 1 2 3 4 Rear View Rear View 1 Service port 1 Service port 2 Connect to interconnect cable 2 Connect to interconnect cable 3 To CPU: USB 2.0 3 Connect to USB 2.0 devices Pos: 46 /806-IHSE/Beschreibung/Geräteansichten/474-xx/Typ L- / R474-BXTS @ 6\mod_1304583818676_6.
Description Pos: 49 /806-IHSE/Beschreibung/Diagnose LEDs/UEB_Diagnose_LEDs @ 6\mod_1304584004723_6.doc @ 51146 @ @ 1 3.7 Status LEDs Pos: 50 /806-IHSE/Beschreibung/Diagnose LEDs/474-xx/Diagnose KVM-Extender-Modul @ 6\mod_1304584091941_6.doc @ 51165 @ 3 @ 1 3.7.1 Status KVM Extender Module The KVM Extender module is fitted with a multi color LED on both sides for overall status indication and with two further LEDs on the back side for indication of the connection status.
Draco vario DVI KVM Extender 3.7.2 Status KVM Extender Module VGA / DVI-I The KVM Extender module with VGA / DVI-I input is fitted with a multicolor LED on the front side of the CPU Unit for indication of connection status. Further information is available via on screen display (OSD) (see manual for the Media / DVI Converter K238-5V (Download)).
Description 3.7.
Draco vario DVI KVM Extender 3.7.4 Status Upgrade Module USB-HID The upgrade module USB-HID is fitted with three further LEDs on the rear side for indication of the connection status: CPU Module CON Module 1 2 1 3 Rear View Pos.
Description 3.7.5 Status Upgrade module USB 2.0 embedded The upgrade module USB 2.0 embedded is fitted with three further LEDs on the rear side for indication of the connection status: CPU Module CON Module 1 2 1 3 Rear View Pos. LED 1 2 Status LED (green) Status LED (green) Status Description Off No USB 2.0 device connected Flashing slowly USB 2.
Draco vario DVI KVM Extender 3.7.6 Status Upgrade Module USB 2.0 The upgrade module USB 2.0 is fitted with a multi color LED on both sides for overall status indication and with two further LEDs on the back side for indication of the connection status. CPU Module 1 2 1 2 CON Module 3 3 Rear View Pos.
Description 3.7.7 Status Monitoring Module SNMP The monitoring module SNMP is fitted with a multi color LED on both sides for overall status indication and with two further LEDs for indication of the network status: 1 2 3 4 Rear View Status LEDs of the SNMP board Pos.
Draco vario DVI KVM Extender 4 Installation Pos: 58 /806-IHSE/Installation/Lieferumfang prüfen/474-xx @ 6\mod_1304584334582_6.doc @ 51255 @ 2 @ 1 4.1 Package Contents Your extender package contains the following items: KVM Extender: KVM Extender pair (CPU Unit and CON Unit) in the vario chassis 1x (redundancy 2x) 5VDC international power supply unit per KVM Extender unit 1x (redundancy 2x) country-specific power cord Quick Setup DVI video cable (1.
Installation Additional content for upgrade module Digital Audio: RCA cable (2.5 m, Cinch male connector) TOSLINK cable (1.8 m, F05 male connector) Additional content for upgrade module USB-HID: USB cable (1.8 m, USB type A to type B) Additional content for upgrade module PS/2: 2x PS/2 cable (1.8 m, 6-pole connector) Additional content for upgrade module USB 2.0 embedded: USB cable (1.8 m, USB type A to type B) Additional content for upgrade module USB 2.0: USB cable (1.
Draco vario DVI KVM Extender Pos: 60 /806-IHSE/Installation/System anschließen/474-xx @ 6\mod_1304584542160_6.doc @ 51273 @ 233 @ 1 4.2 System Setup First time users are recommended to setup the system with the CPU Unit and the CON Unit in the same room as a test setup. This will allow you to identify and solve any cabling problems, and experiment with your system more conveniently.
Installation 4.2.2 Setup of Upgrade Modules The modules can be hot plugged. Upgrade Module Analog Audio / Serial: 1. Connect the audio source to the CPU Unit (e.g. CPU audio output with audio input, CPU audio input with audio output). 2. Connect the audio output on the CON Unit to headphones or suitable speakers. 3. Connect the audio input on the CON Unit to a suitable microphone. Upgrade Module Serial RS422: 1. Connect the CPU to the CPU Unit by using the serial cable. 2.
Draco vario DVI KVM Extender Upgrade Module USB 2.0: 1. Connect the CPU to the CPU Unit (USB 2.0). 2. Connect the USB 2.0 devices to the CON Unit (Connect to USB 2.0 devices). Pos: 61 /806-IHSE/Installation/Installationsbeispiele/UEB_Installationsbeispiele @ 5\mod_1278581564870_6.doc @ 42759 @ 2 @ 1 4.3 Example Applications This section illustrates typical installations of KVM Extenders: Pos: 62 /806-IHSE/Installation/Installationsbeispiele/477-xx_COMP @ 5\mod_1291124264328_6.
Installation 1 2 3 4 5 6 7 KVM Extender (Dual-Head with 4x USB-HID) 1 Source (computer, CPU) 2 KVM Extender CPU Unit 3 Interconnect cable 4 KVM Extender CON Unit 5 Console (monitor, keyboard, mouse) 6 Second monitor (option, only with Dual-Head devices) 7 USB 2.0 devices (option, only with 2x USB 2.0 devices) 8 Audio sink (optional, only with devices with Analog Audio / Serial option or Digital Audio option) Pos: 63 /806-IHSE/Installation/Betriebsmodi/474-xx @ 9\mod_1373975571965_6.
Draco vario DVI KVM Extender 4.4 Operating Modes This section illustrates an overview of possible operating modes of the KVM Extender by combining the various available modules.
Installation 4.5 Overview Upgrade Modules This section illustrates an overview of the available types of upgrade modules for the KVM Extender. L474-BXH L474-BXE Analog Audio +RS232 R474-BXE Full Speed Analog Audio +RS232 R474-BAX Analog Audio +RS232 / L474-BXTC CPU Unit CON Unit R474-BAP 2.0 Analog Audio +RS232 / R474-BDX L474-BDX L474-BSX 2 x HID Full Speed 2.0 L474-BAX L474-BAP R474-BXH 2 x HID Analog Audio +RS422 2.0 High Speed R474-BSX R474-BXTC Analog Audio +RS422 2.
Draco vario DVI KVM Extender 5 Configuration Pos: 66 /806-IHSE/Konfiguration/Übertragungsparame ter/477-xx @ 5\mod_1278937002401_6.doc @ 43075 @ 2 @ 1 5.1 Transmission Parameters The device operates with a proprietary compression method. In default configuration, the device adapts dynamically to monitor resolution and image content. This configuration is suitable for almost all conditions and should only be modified if image quality is not fully satisfactory.
Configuration 5.3 Command Mode During normal use, the console keyboard functions in the usual manner. However, for all KVM Extenders with USB-HID support, you can set the keyboard into a Command Mode by using a specific 'Hot Key' sequence. While in Command Mode, several functions are performed via keyboard commands. To exit Command Mode, press . While in Command Mode, the Shift and Scroll LEDs on the console keyboard will flash. In Command Mode normal keyboard and mouse operation will cease.
Draco vario DVI KVM Extender The 'Hot Key' sequence to enter Command Mode can be changed. The following table lists the 'Hot Key' Codes for the available key sequences: 'Hot Key' Code 'Hot Key' 0 Freely selectable (from 2012-01-12) 2 2x 3 2x 4 2x 5 2x 6 2x 7 2x 8 2x Set freely selectable 'Hot Key' (exemplary) In order to set a freely selectable 'Hot Key' (e.g.
Configuration The following table lists the keyboard commands for the configuration of USB-HID Ghosting: Function Keyboard Command Writes the device descriptions of the input devices connected to the CON Unit into the CPU Unit. Activating the emulation in the CPU Unit. <'Hot Key'>, , , Activates the emulation of already stored device descriptions in the CPU Unit <'Hot Key'>, , , Deactivates the emulation of active device descriptions in the CPU Unit.
Draco vario DVI KVM Extender 5.5.1 Parameters for CPU Units You can write the following parameters into the configuration file of a CPU Unit.
Configuration Shared Operation Parameter Function KBDCON Activate Keyboard Connect (only with redundant CPU Units) MOUCON Activate Mouse Connect (only with redundant CPU Units) RELEASETIME=n Release timer n = 0...9 seconds for Mouse and Keyboard Connect, without parameter = 10 seconds General Settings 5.5.
Draco vario DVI KVM Extender 5.5.3 Parameters for CPU und CON Units You have to write the following parameters into the configuration file of both CON Unit and CPU Unit.
Operation 6 Operation Pos: 72 /806-IHSE/Betrieb/Laden von DDC-Informatio nen/477-xx @ 5\mod_1278937455136_6.doc @ 43130 @ 2 @ 1 6.1 Download of DDC Information By default, data from the internal DDC list is reported to the source (computer, CPU). If these are not optimal settings for the display device, the DDC information of the console monitor can be downloaded and stored internally. The devices have to be configured accordingly (see Chapter 5.2, Page 48).
Draco vario DVI KVM Extender In order to configure a redundant CPU Unit for the operation with two competing CON Units, proceed as follows: 1. Connect a redundant CPU Unit to any source (computer, CPU) by using a mini USB connection. 2. Open the file "Config.txt" that is located on the appearing flash drive of the extender. 3. Activate the release timer by writing the parameter RELEASETIME=n into the second line.
Specifications 7 Specifications Pos: 75 /806-IHSE/Technische Daten/Schnittstellen/UEB_Schnittstellen @ 5\mod_1278578201870_6.doc @ 42114 @ 2 @ 1 7.1 Interfaces Pos: 76 /806-IHSE/Technische Daten/Schnittstellen/DVI-D-Single-Link @ 5\mod_12785782540 58_6.doc @ 42132 @ 3 @ 1 7.1.1 DVI-D Single Link The video interface supports the DVI-D protocol. All signals that comply with DVI-D Single Link norm can be transmitted.
Draco vario DVI KVM Extender Other USB-HID devices The proprietary USB emulation also supports certain other USB-HID devices, such as specific touch screens, graphic tablets, barcode scanners or special keyboards. Support cannot be guaranteed, however, for every USB-HID device. Only two USB-HID devices are supported concurrently, such as keyboard and mouse or keyboard and touch screen. A hub is allowed, but it does not increase the number of HID devices allowed.
Specifications 7.1.6 RJ45 (Interconnect) Communication between Cat X devices requires a 1000BASE-T connection. Connector wiring must comply with EIA/TIA-568-B (1000BASE-T), with RJ45 connectors at both ends. All four cable wire pairs are used. Pos: 82 /806-IHSE/Technische Daten/Schnittstellen/Glasfaser SFP Typ LC @ 5\mod_1278937700855_6.doc @ 43149 @ 3 @ 1 7.1.
Draco vario DVI KVM Extender In this case, choose X-ON / X-OFF software handshake for traffic control at printer and PC.
Specifications Specifications Analog Audio Transmission Format Digitized virtually CD quality audio (16 bit, 38.4 KHz) Signal Level Line-Level (5 Volt Pk-Pk maximum) Input Impedance 47 KOhm Connections CPU Unit 2x 3.5 mm stereo jack plug (audio in & audio out) Connections CON Unit 2x 3.5 mm stereo jack plug (audio in & audio out) Specifications Analog Audio USB 2.0 Transmission Format Digitized virtually CD quality audio, 16 bit (8, 11.025, 16, 22.05, 32, 44.
Draco vario DVI KVM Extender 7.1.11 Digital Audio Interface The digital audio option supports the unidirectional transmission of digital audio data. Up to three sources can be connected to the CPU Unit. The active source is transmitted. If several sources are active, the XLR signal takes priority, otherwise the first active signal. The three connectors on the CON Unit provide concurrent digital audio.
Specifications Compatibility AES/EBU, S/PDIF, EIAJ CP1201, IEC 60958 Standards Dolby Digital, DTS, PCM Bit Depth 24 bit Sample Rate 32 to 192 kHz CPU Unit (Inputs) CON Unit (Outputs) Mini-XLR (AES/EBU; symmetrical, lockable) Coaxial (S/PDIF; RCA, Cinch) Optical (S/PDIF; TOSLINK) Mini-XLR (AES/EBU; symmetrical, lockable) Coaxial (S/PDIF; RCA, Cinch) Optical (S/PDIF; TOSLINK) Pos: 87 /806-IHSE/Technische Daten/Verbindungskabel/UEB_Verbindungskabel @ 5\mod_1279191107845_6.
Draco vario DVI KVM Extender 7.2 Interconnect Cable Pos: 88 /806-IHSE/Technische Daten/Verbindungskabel/Verbindungskabel (Cat X) @ 5\mod_1278578406026_6.doc @ 42205 @ 3 @ 1 7.2.1 Cat X A point-to-point connection is required. Operation with several patch fields is possible. Routing over an active network component, such as an Ethernet Hub, Router or Matrix, is not allowed. Avoid routing Cat X cables along power cables.
Specifications Pos: 91 /806-IHSE/Technische Daten/Verbindungskabel/Verbindungskabel (LWL) @ 5\mod_1278937967667_6.doc @ 43186 @ 3 @ 1 7.2.2 Fiber A point-to-point connection is necessary. Operation with multiple patch panels is allowed. Routing over active network components, such as Ethernet Hubs, Switches or Routers, is not allowed.
Draco vario DVI KVM Extender Pos: 93 /806-IHSE/Technische Daten/Unterstützte Peripherie/UEB_Unterstützte Peripherie @ 5\mod_1278578478761_6.doc @ 42242 @ 2 @ 1 7.3 Supported Peripherals Pos: 94 /806-IHSE/Technische Daten/Unterstützte Peripherie/USB-HID-Geräte @ 5\mod_1278578523558_6.doc @ 42260 @ @ 1 7.3.1 USB-HID Devices The KVM Extender will support most USB-HID devices, including the vast majority of keyboards and mice currently on the market.
Specifications 7.4 Connector Pinouts Pos: 97 /806-IHSE/Technische Daten/Pinbelegungen/Buchse DVI-D Single-Link @ 5\mod_1278578723073_6.doc @ 42333 @ @ 1 Connector DVI-D Single-Link 1.............................8 C1 C2 C5 17...........................24 C3 C4 Pin Signal 1 T.M.D.S data 2 – 9 Pin T.M.D.S data 1 – 17 T.M.D.S data 0 – 2 T.M.D.S data 2 + 10 T.M.D.S data 1 + 18 T.M.D.S data 0 + 3 T.M.D.S data 2 GND 11 T.M.D.S data 1 GND 19 T.M.D.S data 0 GND 4 n.c. 12 n.c. 20 n.c.
Draco vario DVI KVM Extender Connector DVI-I Single-Link 1.............................8 C1 C2 C5 17...........................24 C3 C4 Pin Signal Pin 1 T.M.D.S data 2– 9 T.M.D.S data 1– 17 T.M.D.S data 0– 2 T.M.D.S data 2+ 10 T.M.D.S data 1+ 18 T.M.D.S data 0+ 3 T.M.D.S data 2 GND 11 T.M.D.S data 1 GND 19 T.M.D.S data 0 GND 4 n.c. 12 n.c. 20 n.c. 5 n.c. 13 n.c. 21 n.c. 6 DDC Input (SCL) 14 +5VDC high impedance 22 T.M.D.S clock GND 7 DDC Output (SDA) 15 GND 23 T.M.
Specifications Connector USB Type A Picture 1 2 3 4 Pin Signal Color 1 VCC (+5VDC) Red 2 Data – White 3 Data + Green 4 GND Black Pin Signal Color 1 VCC (+5VDC) Red 2 Data – White 3 Data + Green 4 n.c. – 5 GND Black Pin Signal 1 DATA 2 GND 3 VCC (+ 5VDC) 4 CLK 5 n.c. 6 n.c. Pos: 101 /806-IHSE/Technische Daten/Pinbelegungen/Buchse Mini-USB Typ B @ 5\mod_1278578794167_6.doc @ 42387 @ @ 1 Connector Mini USB Type B Picture 1....
Draco vario DVI KVM Extender Fiber SFP Typ LC Picture 1 Diode Signal 1 Data OUT 2 Data IN Pin Signal Inside VCC (+5VDC) Outside GND 2 Pos: 105 /806-IHSE/Technische Daten/Pinbelegungen/Stromversorgung @ 5\mod_1278578849183_6.doc @ 42423 @ @ 1 Power Supply Picture Pos: 106 /806-IHSE/Technische Daten/Pinbelegungen/D-Sub 9 (Seriell) @ 5\mod_1291128631437_6.doc @ 44882 @ @ 1 D-Sub 9 (Serial) RS232 Picture 1.................5 6...........9 Pin Signal Pin Signal 1 n.c.
Specifications D-Sub 9 (Serial) RS422 Controlling Device Picture 1.................5 6...........9 Pin Signal Pin Signal 1 GND 6 Tx-GND 2 TxA 7 TxB 3 RxB 8 RxA 4 Rx-GND 9 n.c. 5 n.c. Pos: 109 /806-IHSE/Technische Daten/Pinbelegungen/Stereo-Klinkenbuchse 3,5 mm @ 5\mod_1291128765156_6.doc @ 44901 @ @ 1 3.
Draco vario DVI KVM Extender TOSLINK Picture 1 Diode Signal 1 Data IN / OUT Pos: 113 /806-IHSE/Technische Daten/Stromversorgung/474-xx @ 6\mod_1304586284191_6.doc @ 51327 @ 2 @ 1 7.5 Power Supply AC Power Supply Model Max. Current Max. Voltage Frequency 474-BODY2N 700 mA max. 100-240 V 50/60 Hz 474-BODY6R 1,400 mA max. 100-240 V 47-63 Hz 474-BODY6BP 1,300 mA max. 100-240 V 50/60 Hz 474-BODY6BPF 1,300 mA max. 100-240 V 50/60 Hz 474-BODY21/4U 4,000 mA max.
Specifications Power Requirement Power Requirement (per Unit) KVM Extender: Single-Head devices: max. 800 mA Onboard DVI-I devices: max. 1,200 mA VGA: max. 1,700 mA Redundancy devices: max. 1,050 mA Upgrade Modules: Analog Audio / Serial: max. 300 mA Serial(RS422): max. 150 mA Digital Audio: max. 300 mA USB-HID: max. 300 mA PS/2: max. 650 mA USB 2.0 embedded: max. 1,100 mA USB 2.0: max.
Draco vario DVI KVM Extender 7.7 Size Devices in the 2-fold Vario Chassis 1 CPU Unit / CON Unit 145 x 147 x 41 mm (5.7" x 5.8" x 1.7") Shipping Box 210 x 140 x 165 mm (8.3" x 5.5" x 6.5") Devices in the 2-fold Vario Chassis 2 CPU Unit / CON Unit 221 x 147 x 41 mm (8.7" x 5.8" x 1.7") Shipping Box 550 x 365 x 115 mm (21.7" x 14.4" x 4.5") Devices in the 4-fold Vario Chassis CPU Unit / CON Unit 293 x 147 x 41 mm (11.5" x 5.8" x 1.7") Shipping Box 550 x 365 x 115 mm (21.7" x 14.4" x 4.
Specifications Pos: 117 /806-IHSE/Technische Daten/Transportgewicht /474-xx @ 6\mod_1304586413879_6.doc @ 51363 @ 2 @ 1 7.8 Shipping Weight Devices in the 2-fold Vario Chassis 1 CPU Unit / CON Unit 0.4 kg (0.9 lb) Shipping Box 2.2 kg (4.9 lb) Devices in the 2-fold Vario Chassis 2 CPU Unit / CON Unit 0.8 kg (1.8 lb) Shipping Box 2.6 kg (5.7 lb) Devices in the 4-fold Vario Chassis CPU Unit / CON Unit 0.9 kg (2.0 lb) Shipping Box 3.4 kg (7.
Draco vario DVI KVM Extender 8 Troubleshooting Pos: 119 /806-IHSE/Hilfe im Problemfall/Allgemeine Störung/474-xx @ 9\mod_1373964024756_6.doc @ 77427 @ 2 @ 1 8.1 General Failures Diagnosis Possible Reason Measure Config.txt parameter without function Parameter not set or saved Write parameter into Config.txt file and save changes. Start Commanc #CFG not set Write start command #CFG into first line of the Config.txt file.
Troubleshooting 8.2 Blank Screen CPU Module 1 2 1 2 CON Module 3 1 3 Rear View 2 1 2 3 3 Rear View Diagnosis Possible Reason Measure LED 3 off Power supply Check power supply units and the connection to the power network. LED 1 on or LED 2 off Connection between CON Unit and CPU Unit Check interconnect cables and connections.
Draco vario DVI KVM Extender 8.3 USB-HID CPU Module 1 2 1 2 CON Module 3 3 Rear View Diagnosis 1 Possible Reason 2 1 2 3 3 Rear View Measure Keyboard LEDs Keyboard in Command Shift and Scroll Mode are blinking Press to leave Command Mode. CPU Unit: LED 3 green or violet No USB connection to CPU Check connection of USB cable to CPU; select another USB port if necessary. Remove USB and power cable and restart CPU. Connect power cable first.
Troubleshooting 8.4 Serial Connection Diagnosis Possible Reason Measure Serial device not operational Settings of the serial interface Check Baud rate and general settings. No serial connection to CPU Check connection via serial cable. No serial connection to end device (e.g. touch screen, keyboard) Connect serial end device and switch it on. Check connection via serial cable. Hardware handshake Adjust serial interface to X-ON / X-OFF software handshake.
Draco vario DVI KVM Extender 8.6 Digital Audio CPU Module CON Module 1 1 Rear View Rear View Diagnosis Possible Reason Measure CPU Unit: LED 1 red No audio connection to CPU / audio source Connect digital audio source. Check connection of audio cable. No signal Switch digital audio source on. Activate digital output at CPU / audio source. No audio connection to audio sink (e.g. speakers) Connect digital audio sink. Check connection of audio cable.
Troubleshooting 8.7 Upgrade Module USB-HID CPU Module CON Module 1 2 1 3 Rear View 2 3 Rear View Diagnosis Possible Reason Measure LED 1 / 2 off Device at higher / lower USB-HID port not detected Check connection of USB cable to USB-HID device. Connect USB-HID device. Contact dealer if necessary. CPU Unit: LED 3 off Connection between CON Unit and CPU Unit Check interconnect cable and connectors. CON Unit: LED 3 off Keyboard in Command Mode Press to leave Command Mode.
Draco vario DVI KVM Extender Pos: 127 /806-IHSE/Hilfe im Problemfall/Störung am USB-2.0-Embedded-Anschluss/474-xx @ 7\mod_1331802913522_6.doc @ 58211 @ 2 @ 1 8.8 USB 2.0 embedded CPU Module CON Module 1 2 1 3 Rear View 2 3 Rear View Diagnosis Possible Reason Measure CPU & CON Unit: LED 3 off No connection to CPU Check connection USB cable to CPU; select another USB port if necessary. Remove USB and power cable and restart CPU. Connect power cable first.
Troubleshooting Pos: 129 /806-IHSE/Hilfe im Problemfall/Störung am USB-2.0-Anschluss/474-xx @ 6\mod_1304586956738_6.doc @ 51494 @ 2 @ 1 8.9 USB 2.0 CPU Module 1 2 1 2 CON Module 3 3 Rear View 2 3 1 2 3 1 Rear View Diagnosis Possible Reason Measure CPU Unit: All LEDs off No connection to CPU Check connection USB cable to CPU; select another USB port if necessary. Remove USB and power cable and restart CPU. Connect power cable first.
Draco vario DVI KVM Extender 9 Technical Support Prior to contacting support please ensure you have read this manual, and then installed and set-up your KVM Extender as recommended. 9.1 Support Checklist To efficiently handle your request it is necessary that you complete a support request checklist (Download). Please ensure that you have the following information available before you call: 9.
Certificates 10 Certificates Pos: 132 /806-IHSE/Zertifikate/ATB_Europäische Konformitätserklärung @ 5\mod_1278579640901_6.doc @ 42686 @ 2 @ 1 10.
Draco vario DVI KVM Extender 10.2 North American Regulatory Compliance This equipment has been found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Certificates 10.4 WEEE The manufacturer complies with the EU Directive 2012/19/EU on the prevention of waste electrical and electronic equipment (WEEE). The device labels carry a respective marking. Pos: 135 /806-IHSE/Zertifikate/ATB_RoHS @ 5\mod_1278579714214_6.doc @ 42722 @ 2 @ 1 10.
Draco vario DVI KVM Extender 11 Glossary The following terms are commonly used in this guide or in video and KVM technology: Term Explanation AES/EBU Digital audio standard that is officially known as AES3 and that is used for carrying digital audio signals between devices. Cat X Any Cat 5e (Cat 6, Cat 7) cable CGA Color Graphics Adapter (CGA) is an old analog graphic standard with up to 16 displayable colors and a maximum resolution of 640x400 pixels.
Glossary Term Explanation Dual Link A DVI-D interface for resolutions up to 2560x2048 by signal transmission of up to 330 MPixel/s (24-bit) Dual-Head A system with two video connections DVI Digital video standard, introduced by the Digital Display Working Group (http://www.ddwg.org). Single Link and Dual Link standard are distinguished. The signals have TMDS level. DVI-I A combined signal (digital and analog) that allows running a VGA monitor at a DVI-I port – in contrast to DVI-D (see DVI).
Draco vario DVI KVM Extender Term Explanation Single Link A DVI-D interface for resolutions up to 1920x1200 by signal transmission of up to 165 MPixel/s (24-bit). Alternative frequencies are Full HD (1080p), 2K HD (2048x1080) and 2048x1152. Single-Head A system with one video connection Single-mode 9µ single-mode fiber cable S-Video (Y/C) S-Video (Y/C) is a video format transmitting luminance and chrominance signals separately. Thereby it has a higher quality standard than CVBS.
