Infrared Portable Space Heater 1500 Watts with Two Heat Settings Thermal Cutoff Protection Tip-Over Switch Room Temperature LED Display Precision Temperature Control Easy Push-Button Controls Remote Control Advanced Dual Heating System (ADHS) Model No.
CONGRATULATIONS! he Dr. Infrared Heater you have just purchased is a safe and powerful heater, designed to heat a room after a few minutes of operation. The far-infrared Quartz-PTC heating system is an excellent choice for safely heating whole rooms, while saving on heating costs. T Additionally, this heater includes an overheat protection system, and an inlet air overheat protection system designed to ensure your safety.
4. Do not operate the heater with a damaged cord or plug, or after the heater malfunctions, has been dropped, or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair. 5. Do not use outdoors. 6. This heater is not intended for use in bathrooms, laundry areas or similar locations. Never locate the unit where it may fall into a bathtub or other water container. 7.
18. Make sure the plug is fully inserted into an appropriate receptacle. Be mindful that receptacles also deteriorate due to aging and continuous use. Check periodically for signs of overheating or deformations of the plug. If any overheating or deformation occurs, immediately discontinue using the heater and contact Dr. Infrared Heater Authorized Service Center. 19.CHECK YOUR HEATER CORD AND PLUG CONNECTIONS. Faulty wall outlet connections or loose plugs can cause the outlets or plug to overheat.
Advanced Dual Heating System (ADHS) - Dr. Heater is the first to feature a dual heating system for maximum heat transfer rate. It combines the energy efficiency of infrared heat with the comfort of convection heat to heat your room fast and comfortably—without hot spots and cold spots. A F TM B H G C D E Features A. “Cool-Touch” cabinet B. POWER button C. Decrease temperature button D. Increase temperature button E. MODE button F. LED temperature display G. Standby ON/OFF button H.
Steps 1, 2, 3 to turn on the heater Step 1 – Plug in power cord to outlet. The heater default setting is 68ºF, if room temperature is above 68ºF, the heater won’t start if the room temperature is higher than the set temperature. Please check Room Temp, and increase Set Temp to start heater. Note: Heater will not turn on if the room temperature is higher than 86ºF. Step 2 – Press power button on the unit.
Operating Instructions 1. Plug the power supply cord into a grounded wall outlet. (120VAC, 60Hz) Important: This heater comes with a grounded (three-prong) plug. The grounded plug must be used with a grounded outlet. Do not use an adapter in a two-slot wall outlet unless the ground plug of the adapter properly connects to a building ground. Using the heater without a properly grounded outlet or adapter could result in an electric shock hazard. The cord has a plug as shown at A in the following figure.
reached the set temperature. The heater will stop heating and initiate component cooling process before turning off the fan. Once the desired temperature is achieved, the heater will maintain the room to the set temperature. 7. SETTING THE TEMPERATURE Choose the desire Mode: ECO, HIGH, or LOW. To set the desired temperature: Press the button once until the numeric temperature starts flashing. button Press the button again to increase the temperature or the to decrease the temperature.
Instructions for the Use of the IR Remote Control The buttons on the remote controller functions in the same manner as those on the control panel on the front of the heater. Set the timer by using the remote control. Setting the Timer 1. Press the TIMER button until Set Time starts flashing. The default value is 3 hours. 2. Press the “+” button to increase the set time or the “–” button to decrease the set time. The timer can be set from 1 to 12 hours.
3. Release the filter by pushing the filter up from below (Figure 1). 4. Remove the filter by pulling down and out (Figure 2). 5. Clean the filter by vacuuming. 6. Replace the filter by sliding the top upwards into the spring loaded slot on the back of the heater (Figure 2). Then gently push the bottom of the filter into place (Figure 1). Figure 1 Figure 2 Warning: Any other servicing needed must be performed by an authorized service representative. Do not attempt to service the unit yourself.
Warranty Information Register your product at our website: Or visit DrHeaterUSA.com/register-your-heater Feedback Love it? Help us make the product more for you. Let us know with a customer review. Please visit: https://www.amazon.com/review/review-your-purchases# At Dr. Heater USA, we are committed to bringing top quality alternative & supplemental heating products to our customers. Note: There may be a trace of smoke or odor when the unit is first operated. Do not be alarmed.
Dr. Heater USA 860 Mahler Road Burlingame, CA 94010 Tel: 1-800-317-1688 EMAIL: SERVICE@DRHEATERUSA.COM Dr Heater USA @DrHeaterUSA Dr. Heater USA Dr.
QUESTIONS AND ANSWERS If the heater cycles ON/OFF without heating: Please note: This is a smart heater that monitors the room temperature and produces heat only when needed. You can set the desired room temperature with the heater in ECO mode. (The factory default setting is 68 °F.) For an example of how the heater works, let’s say you set the temperature for 70 °F, the heater will run on HIGH until the room temperature reaches 70°F. The heater will switch to run on LOW for 10 minutes.
How to turn off the heater: Switch to STANDBY mode or POWER OFF the heater. Does the blower cycle use much electricity? The blower fan will run for 60 seconds every 5 or 30(night mode) minutes to clear residual heat inside the chamber, while at the same time measuring the room temperature. This does not use much power to operate. Why does the blower fan keep running after I have pressed the power OFF button? The blower fan will continue to run until the heat chambers cool down.
My home is not well insulated; will this heater help me? Yes, but it may take a little longer to heat the room. The outside temperature will also have an impact on heating time. Once the room has reached the desired temperature, it will cycle on and off accordingly. Can the heater be used in a bathroom? It is not recommended due to a bathroom’s high level of moisture.
What is zone heating? Zone heating focuses heat where people spend the most time. After all, there is no point in heating multiple rooms to +68 degrees when not in use. Can I use an extension cord, surge protector, or power strip with my heater? No. The DR. INFRARED HEATER is designed to plug directly into a grounded 120V 15 Amp or higher circuit receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip). How many kilowatts per hour does the heater use? The DR.
