0,000W/240V WALL / CEILING MOUNTED GARAGE HEATER OWNER’S MANUAL Model No.
TABLE OF CONTENTS Important Instructions……………………………………….3-4 Installing Instructions………………………. ……………… 5-10 Specifications and Wiring Diagram ………………………. 11 Parts of the Heater……………………….…………..……...12-13 Operating Instructions……………………….………....….. 14-17 Maintenance and Cleaning……………………………….. . 18 Troubleshooting……………………………………………. .
IMPORTANT INSTRUCTIONS PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS HEATER NOTE: There may be a trace of smoke or odor when unit is first operated. Don’t be alarmed. This indicates that a drop of oil fell on the heating coil during the manufacturing process. It will quickly evaporate and should not re-occur. Make sure that the room in which the appliance is located is well ventilated during this operation.
8) This heater should be installed at least 6 feet (1.8 m) from the floor and no closer than 1 foot (0.3 m) from any adjacent surfaces or walls. Keep at least 4.5 inches (0.12m) from the back wall, regardless of whether the wall mount bracket is used. 9) Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire and potentially damage the heater. 10) To prevent a possible fire, do not block air intakes or exhaust in any manner.
INSTALLATION INSTRUCTIONS WARNING: All wiring must be installed by a certified/licensed electrician. The heater must be grounded in accordance with applicable national and local building codes. WARNING: To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater. All wiring procedures and connections should be in accordance with applicable national and local codes. NOTE: Compatible with a 240V Line Voltage Double Pole Wall Thermostat.
·Remote Control ·Battery x 2 Qty 2 1 2 2 2 2 ·Screw Kit Screw Kit Contents Description M10 Explosion Screw M10x80mm Screw M10 Nut Ф10 Washer Ф10 Spring Washer Ф10 Rubber Pad WARNING: To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater. INSTALLATION INSTRUCTIONS: 1. This heater should be installed at least 6 feet (1.8 m) from the floor. This minimum distance must be maintained. 2. Do not install closer than 1 foot (0.
. Attach the mounting bracket to the wall and secure with mounting screws. 8. Loosen the tilt adjustment knobs; remove the cart. 9. Align the Hang Bracket to the knob screw holes. 10. Re-insert the knob and tighten. Hang Bracket Knob Rubber Pad 11. Hook the unit to the mounting bracket and let the unit hang from the mounting bracket. 12. Insert the bolt provided through the mounting bracket and the heater handle. Tighten with the nut and washer.
13. Loosen the screw to remove the wiring compartment/connection cover in the rear of the heater. There are three pigtail leads, both Black (L1) and Red (L2) are for power connection; Green is for grounding connection. Watch Window For Wiring 14. Run the electrical power supply cable in flexible conduit and connect to the wiring compartment via the knock-out at back side of the unit. The rectangle hole is watch window for wiring. 15.
B. Press the rocker switch to WALL THERMOSTAT, insert two 16AWG wires to Terminal A inside the heater. Make sure to tighten the screws in Terminal A. TERMINAL A Blac 16AWG WIRES Red C.
D. Insert wires into the Thermostat Outlet Box, and screw up the thermostat. E. Cover the thermostat.
SPECIFICATIONS 10,000W/240V WALL / CEILING MOUNTED GARAGE HEATER Model: DR-910F Voltage: 240 V Watts: 10,000 W Frequency: 60 Hz Recommended Heating Capacity: 1.25watts / ft³ (0.
PARTS OF THE HEATER A B C H E D K A. B. C. D. E. F. G. H. F G J L I M Wall Mount Bracket Ceiling Bracket Upper Housing Louver for air direction Tilt Adjustable Knob Lower Housing Front Exhaust Grill ON/OFF Switch N I. Internal/Wall Thermostat Switch J. Control Panel K. Alarm LED L. Power LED M. Timer LED N.
O Q P R S O. Increase Temperature button P. Decrease Temperature button Q. Thermostat button R. Timer button S.
OPERATING INSTRUCTIONS WARNING - The heater must be properly installed before it is used. HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH: Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70. A circuit breaker must be installed and serviced only by qualified electrical personnel. Always use a properly rated voltage sensing device to confirm power is off. The switch on the heater is to start the Fan and Heater.
Selecting Inside Thermostat: 1 Turn the ON/OFF switch to OFF position, and then turn the thermostat rocker switch to INSIDE THERMOSTAT as indicated below: 2 Turn the ON/OFF switch to ON position again, the heater will work on the inside thermostat mode. Selecting Wall Thermostat: 1 Turn the ON/OFF switch to OFF position, and then turn the thermostat rocker switch to WALL THERMOSTAT as indicated below: 2 Turn the ON/OFF switch to ON position, the heater will work on the wall thermostat mode.
Insert the batteries into the remote control as shown below: NOTE: Remove the batteries if the remote control is not to be used for a month or more. Batteries left in the remote may leak and cause damage. DO NOT MIX OLD AND NEW BATTERIES! DO NOT MIX ALKALINE, STANDARD (CARBON-ZINC) OR RECHARGEABLE (NICKEL-CADMIUM) BATTERIES! TURNING THE HEATER ON To turn the heater ON, press the ON/OFF rocker switch to ON position, the power LED will turn on and display the room temperature.
the setting temperature - 2℉, and will turn off when the room temperature is equal to or greater than the setting temperature+2℉. Note: If you set the thermostat switch to WALL THERMOSTAT, press the + and - button cannot set the temperature, the heater will run in ON or OFF heating according the wall thermostat setting temperature. SETTING THE TIMER (with the remote control) Press the TIMER button until Set Time starts flashing. The default value is 3 hours.
MAINTENCE AND CLEANING No user maintenance on this heater should be undertaken except regular cleaning as described below. All other servicing or maintenance should be performed by qualified service personnel. Before any cleaning, make sure that: 1. Power supply is disconnected at the source. Switch off the circuit breaker. 2. Wait 60 minutes to ensure the heating element has cooled down. Your heater is now ready for cleaning. Regular Cleaning: 1.
TROUBLESHOOTING If your heater fails to operate, please follow these procedures: This heater is intended to be a wall/ceiling-mounted heater. It has a thermal cut-off protection. If the thermal cut-off protection trips, switch off the power. Switch off the circuit breaker. The unit should reset automatically after 10 minutes. If the thermal cut-off protection trips again, consult a certified/licensed electrician to determine the reason for overheating.
PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF. DOING SO COULD CAUSE DAMAGE TO THE HEATER OR PERSONAL INJURY. QUESTIONS AND ANSWERS Why can’t I change the set temperature by press the + - button on the remote? Please follow the steps below: 1 Turn the ON/OFF switch to OFF position 2 Turn the thermostat rocker switch to INSIDE THERMOSTAT 3 Turn the ON/OFF switch to ON position. 4 Press the POWER button on the remote to turn the heater ON. 5 Press the THERMOSTAT button.
Warranty Information Register your product at our website: Or visit DrHeaterUSA.com/register-your-heater Feedback Love it? Help us make the product more for you. Let us know with a customer review. Please visit: https://www.amazon.com/review/review-your-purchases# At Dr. Heater USA, we are committed to bringing top quality alternative & supplemental heating products to our customers. Dr. Heater USA 860 Mahler Road Burlingame, CA 94010 Tel: 1-800-317-1688 EMAIL: SERVICE@DRHEATERUSA.
Dr. Heater USA Dr.
