Carbon Infrared Heater Indoor/Outdoor 3000 Watts Owner’s Manual Model No.
Warning THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE, We cannot be liable for any damages caused by failure to observe these instructions. IMPORTANT INSTRUCTIONS READ CAREFULLY-The infrared heater is designed for safe operation. Nevertheless, installation, maintenance and operation of the heater can be dangerous. Observing the following procedures will reduce the risk of fire, electric shock, injury to person and keep installation time to a minimum.
19. If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. 20. Parts of the heater may exceed 200℃, Contact with the heating tube, reflector, or metal parts near the heating tube, may cause severe BURNS. To avoid burns, do not let bare skin touch hot surface. 21. ALWAYS allow the heating element to cool at least 10 minutes before touching the heating tube or adjacent part 22.
This heater is for use at 240 volts. The cord has a plug as shown in D in Figure 60.1. No adapter is available for this blade configuration, and none should be used. The type outlet is a 240 volt grounding outlet. When properly installed, it provides a ground connection through the cord to the heater to protect the operator from electric shock. Mount Instruction Required hardware contents H1 H1 3|Pa g e H2 H2 H3 H3 H4 H5 No. Desc. Qty No. Desc.
Attention:Digital display position should be on left for correct installation direction 1. Mark the locations using the provided dimensions in Fig - 1a and using the holes on the Lshaped bracket as a guide. Make sure the distance between 2 L-shaped brackets is 35mm/1.38”. Mounting Height: maintain at least 2.4m / 7.9 ft distance between the heater and the floor. 1.1 " 1.1 " 1.38 " H1 Fig - 1a 2. Drill holes with a smaller diameter drill bit than the plastic anchor (H2) as shown in Fig - 2a.
4. Using a screwdriver mount the assembled L-shaped bracket (H1) to the anchors using screws (H3) as shown in Fig - 4a. H3 H3 H3 H3 Fig - 4a 5. Take off the 4 screws on the back of the heater. And use the 4 screws to fasten the heater on the L-shaped bracket by screwdriver as shown in Fig - 5a. Secure the 2 L-shaped bracket (H1) with 4 screws Take off 4 screws on the back of the heater Fig - 5a 6. Assembly the 4 L-shaped brackets (H1) with 2 nuts (H4) and 2 screws (H5) as shown in Fig - 6a.
. Mounting Height: maintain at least 2.4m / 7.9ft distance from the heater to the ground as shown in Fig - 7a, Fig - 7b, Fig - 8a, Fig - 8b. Min 2.4m / 7.9ft Fig - 7a Min 2.4m / 7.9ft Fig - 7b For ceiling mounted: The heater’s working angle is between 45 ° - 90 ° Min 2.4m / 7.9ft Fig - 8a Min 2.4m / 7.
At least 2.4m / 7.9 ft mounting height Indoor or well protected environments will generally exceed average coverage areas. 2.4m / 7.9ft Heater can provide less than average coverage in extremely cold/windy conditions. WARNING THE POWER CORD MUST PLUG INTO A GFCI OUTLET FOR OUTDOOR USE. Ensure main power is OFF before commencing installation. The supplied main cable must not contact the surface of the heater during operation.
8|Pa g e
FUNCTION & OPERATION A) The heater must be properly installed before it is used. B) The heater can be used at well-protected outdoor area with a height 2.4 meters fixed mounted installed, user-operated devices intended to reduce the risk of fire, electric shock, or injury to persons; must follow instructions. Do not change the heater structure, it may cause a fire risk. C) Storage: PLUG-OFF, Store the heater in a cool, dry location when not in use to prevent dust and dirt build up.
OPERATING Operating unit with built-button 1. Apply power to the heater. The heater will be on standby mode display (- -) on the LED screen. 2. Press the button on the unit to cycle through the functions, heat levels (L1 - L2), standby, and off. Remote Control Instructions POWER BUTTON UP BUTTON DOWN BUTTON TIMER BUTTON HEAT LEVEL BUTTON POWER BUTTON: Turn the heater off. UP BUTTON: Increase timer or heat level. DOWN BUTTON: Decrease timer or heat level.
Caution: When the appliance is not operated for a long period of time, cleaning or maintenance is conducted or when the location of the heater is changed, the heater should be turned to OFF and unplugged from the electrical connection. Periodic inspection and removal of dirt and contaminants will ensure that equipment can be operated safely. Troubleshooting 1. Check if the power cord is plugged into an electrical outlet, if not, plug in. 2. Check if electricity to the main fuse is working 3.
5. DO NOT immerse the heater in water 6. Wait until the heater is completely dry before use. Storage: Store the heater in a cool, dry location when not in use to prevent dust and dirt build-up. Wrap the power cord with ties. Use packaging cartons to store. ATTENTION: 1. Always disconnect the heater from the electricity supply and allow it to cool before attempting to work on it. 2.
Warranty Information Register your product at our website: Or visit DrHeaterUSA.com/register-your-heater Feedback Love it? Help us make the product more for you. Let us know with a customer review. Please visit: https://www.amazon.com/review/review-your-purchases# At Dr. Heater USA, we are committed to bringing top quality alternative & supplemental heating products to our customers. Note: There may be a trace of smoke or odor when the unit is first operated. Do not be alarmed.
