Installation Guide
Straw-applied version:
1. Shake can vigorously for 1 minute
before dispensing and between
uses.
2. Attach the nozzle by twisting it
clockwise into the valve. Press the
button until the appropriate size
of foam bead is achieved. Fill gap
less than 1/3 full to allow for proper
expansion.
3. If gap is overfilled, stuff excess
cured foam into gap with a blunt
tool or trim away with a sharp knife.
Foam can be be trimmed in 30
minutes.
4. Clean straw periodically by rubbing
the end on soft wood to free it from
foam.
5. When finished, bend the straw
back onto the plug on top of the
trigger assembly. The plug prevents
moisture from entering and curing
inside the straw or valve.
6. To use after storage, gently rotate
or twist the straw to break the
adhesive bond of the foam. Pull the
straw off of the plug and dispense.
Cleanup
On solid surfaces, uncured foam can
be dissolved with GREAT STUFF
PRO
™
Gun Cleaner. Cured foam
must be mechanically removed or
allowed to wear off in time.
a can of GREAT STUFF PRO
™
Gun
Cleaner to the foam dispensing gun
and spray until all foam is blown
out of the dispensing gun and only
cleaner is visible (approximately
half the can of cleaner will be used).
Allow the gun to sit for several
minutes and repeat with a second
flush.
TYPICAL APPLICATIONS
Outdoor water faucet
Pipe penetration
Electrical wire penetration
Wall-ceiling juncture
Attic hatch HVAC vent
For Technical Information: 1-866-583-BLUE (2583) (English) . 1-800-363-6210 (French)
For Sales Information: 1-800-232-2436 (English) . 1-800-565-1255 (French)
www.dowgreatstuff.com
Printed in U.S.A.
a proud partner of
®™Trademark of The Dow Chemical Company (“Dow”) or an affiliated company of Dow
Habitat for Humanity is a registered service mark owned by Habitat for Humanity International
NOTICE: No freedom from any patent owned by Dow or others is to be inferred. Because use conditions and applicable laws may differ from one location to another and may change with time, Customer is responsible for
determining whether products and the information in this document are appropriate for Customer’s use and for ensuring that Customer’s workplace and disposal practices are in compliance with applicable laws and other
government enactments. The product shown in this literature may not be available for sale and/or available in all geographies where Dow is represented. The claims made may not have been approved for use in all countries
or regions. Dow assumes no obligation or liability for the information in this document. References to “Dow” or the “Company” mean the Dow legal entity selling the products to Customer unless otherwise expressly noted.
FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED.
Dow Polyurethane Foam Insulation and Sealants
call Dow at 1-866-583-BLUE (2583) or contact your local building inspector. In an emergency, call 1-989-636-4400 in the U.S. or 1-519-339-3711 in Canada.
long sleeves, gloves, and goggles or safety glasses. Provide adequate ventilation or wear proper respiratory protection. Contents under pressure.
or safety glasses. Provide adequate ventilation or wear proper respiratory protection. Contents under pressure.
Building and/or construction practices unrelated to building materials could greatly affect moisture and the potential for mold formation. No material supplier including Dow can give assurance that mold will not develop in
any specific system.
mounted on the foam dispensing
gun. This will dissolve the lip seals
inside the gun and render it useless.
Foam escaping at the handle or
trigger indicates a faulty seal. If
this happens, the gun should be
replaced.
Safety and
Conditions of Use
Data Sheet carefully before use.
™
Gun Cleaner
is flammable and contains acetone
and propane. Vapor may travel
to other rooms. Ensure adequate
ventilation. Shut off all pilot lights
and extinguish open flames;
eliminate all sources of ignition
before use. Do not smoke or use
lighters or matches while dispensing
foam.
Provide adequate ventilation or wear
proper respiratory protection.
glasses.