Cut Sheet

• Sleeve
• Hex Head
• Zinc Plated
Sleeve Anchors Hex Head • Zinc Plated | PC 4550
“AT” tool must be used for proper installation.
Sold separately from DA/DAS anchors
“AT” Tool For DA Anchors | PC 4510
• Drop In
• Steel or Stainless Steel
• Zinc Plated
Drop In Anchors: This steel anchor performs well in a variety of
concrete strengths. Can be used in brick. Any head style screw
can be used. The screw can easily be removed or loosened and
retightened. Drill hole in concrete and drop anchor into hole. Place
setting tool over anchor and hammer until set. ICBO approved.
B6
Drop In Anchors | PC 4500, 4310
To Order: Phone [phone] / Fax [phone]
ANCHORS
Steel Zinc Plated | PC4500
DA25 27600 1/4-20 3/8" AT25 100 1000 2.33
#
C
DA38 27605 3/8-16 1/2" AT38 50 500 3.07
#
C
DA50 27610 1/2-13 5/8" AT50 50 500 5.94
#
C
DA58 27615 5/8-11 7/8" AT58 25 25 7.72
#
C
DA75 27620 3/4-10 1" AT75 25 25 8.33
#
C
Stainless Steel | PC4310
DAS25 70260 1/4-20 3/8" AT25 100 1000 2.55
#
C
DAS38 70262 3/8-16 1/2" AT38 50 500 3.50
#
C
DAS50 70264 1/2-13 5/8" AT50 50 500 5.95
#
C
DAS58 70266 5/8-11 7/8" AT58 25 25 6.20
#
C
DAS75 70268 3/4-10 1" AT75 25 25 6.72
#
C
CAT NO UPC ANCHOR SIZE DRILL SIZE REQUIRED TOOL STD MSTR WT/STD UNIT
( “AT” Tool - SOLD SEPARATELY - Must Be Used For Proper Installation )
AT25 27630 1/4" DA25/DAS25 1 10 0.14# Ea
AT38 27635 3/8" DA38/DAS38 1 10 0.25# Ea
AT50 27570 1/2" DA50/DAS50 1 10 0.41# Ea
AT58 27575 5/8" DA58/DAS58 1 10 0.55# Ea
AT75 27580 3/4" DA75/DAS75 1 10 0.77# Ea
CAT NO UPC SIZE ANCHOR TYPE STD MSTR WT/STD UNIT
Sleeve Anchors: Similar to the wedge anchor. It can be used in the
same materials as the wedge anchor, but can also be used in soft
concretes because the compression load can be distributed over
a longer length. Can be installed through the fixture. Assemble nut
and washer on stud and insert into predrilled hole. Anchor is ham-
mered into hole until the nut is seated. ICBO approved
SA14138 59330 1/4" 1-3/8" 1-1/8" 3/16-24 1/4" 100 1000 2.47# C
SA14214 59332 1/4" 2-1/4" 1-1/8" 3/16-24 1-1/8" 100 1000 3.26# C
SA516112 59334 5/16" 1-1/2" 1-1/4" 1/4-20 1/4" 100 1000 4.32# C
SA516212 59336 5/16" 2-1/2" 1-1/4" 1/4-20 1-1/4" 100 1000 6.15# C
SA38178 59338 3/8" 1-7/8" 1-1/2" 5/16-18 3/8" 50
500 3.80# C
SA38300 59340 3/8" 3" 1-1/2"
5/16-18 1-1/2" 50 500 5.15# C
SA12214
59342 1/2" 2-1/4" 1-7/8" 3/8-16 3/8" 25 250 3.32# C
SA12300 59344 1/2" 3" 1-7/8" 3/8-16 1-1/8" 25 250 4.02# C
SA12400 59346 1/2" 4" 1-7/8" 3/8-16
2-1/4" 25 250 5.08# C
ANCHOR DIA/ ANCHOR MIN BOLT DIA MAX MATERIAL
CAT NO UPC DRILL BIT SIZE LENGTH EMBEDMENT THREAD/INCH THICKNESS STD MSTR WT/STD UNIT