Assembly Guide
In order to ease the assembly, you should separate and identify the parts first Necessary hardware for the assembly * Included in the kit * Not included in the kit Locking nut, no key tightening required. Do not place the parts directly onto the floor. Use a cardboard sheet or a mat to place the parts, during the separation and assembly. IMPORTANT In order to avoid severe or even fatal injuries, follow the instructions carefully.
WARNING 55l b Maximum weight supported by shelf P10 Upper Back P3 Left Side P5 P19 Top Shelf 55l b P9 Lower Back 55l b 55l b P7 Bottom P22 P2 Left Door Right Side P23 Right Door F1 F2 Qty. 36 Qty. 36 Hardware list F7 F13 F15 F10 Qty. 4 Qty. 1 Qty. 1 Qty. 2 F11 Qty.
STEP 1 1 - Fit part P7 inside part P3. 2 - Fit both parts in the frontal side, with F1and F2. 1 F1 4x F2 P3 4x 2 P7 WARNING Do not tighten the screw completely. STEP 2 1 - Fit part P2 inside part P7. 2 - Fit both parts in the frontal side, with F1 and F2. F1 1 4x F2 4x P3 P7 WARNING Do not tighten the screw completely.
STEP 3 F1 1 - Fit part P5 between part P2 and P3 2 - Check that all 4 tabs have been fitted 3 - Fit part P5 to parts P2 and P3, at the frontal side, with F1 and F2. 1 4x F2 2 4x P5 P3 P7 P2 3 WARNING Do not tighten the screw completely. STEP 4 1 - Turn the cabinet with the back side upwards. 2 - Fit parts P2 and P3 to parts P5 and P7 with F1 and F2. F1 WARNING Do not tighten the screw completely.
STEP 5 1 - Fit part P10 into parts P2, P3 and P5 Check that all fits are supported over the bolts. 2 - After fitting the parts, screw the bolts until locked. 1 Position part P10 on the P5 side for mounting the P2 2 STEP 6 WARNING P10 P5 Do not tighten the screw completely. P3 P7 1 - Fit part P9 into parts P2, P3 and P7 Check that all fits are supported over the bolts. 2 - After fitting the parts, screw the bolts until locked.
STEP 7 F10 1 - Put the cabinet a flat surface. 3 - To assembly the cabinet with caster, align the F10 and F11 to the holes in part P7 2 - Completely tighten all screws. and fix them with F1 and F2. 4 - WARNING: Casters with lock (F11) must be fitted in the frontal side of the cabinet 2x F11 P3 2x F1 P5 P7 P2 E C FA UR 16x AT S FL F2 WARNING After tightening the screws, make sure the cabinet does not appear to be misaligned.
STEP 9 1 - Fit the lower part P19 in diagonal position to insert it inside the cupboard 2 - Lean part P19 in part P2, P3 and place it over the F7 detailed in the figure here below 3 - Lower the other side of part P19, leaning it over the left F7 F7 P5 P3 P19 P2 P7 STEP 10 1 - To assembly the doors, fit door P23 lower hinge bolt inside the bushing fixed in part P7 Then, pull down the pin of door P23 upper hinge; align the door and release the pin to fit the bushing fixed in part P5 2 - Repeat the step f
WARRANT S TERMS This product has the guarantee for a period of twelve (12) months, this limited warranty is effective from the date of the original consumer purchase. Proof of original purchase date is required to obtain service or replacement under this limited warranty. Once the defect of manufacture has been verified, the consumer should contact the store where he purchased the product. In the warranty period, any defective parts will be replaced free of charge by another of the same line and model.
