Installation & Assembly

ManualsBrandsDotted Line ManualsGarage & Outdoor Storage & OrganizationLynn 55.5" H x 24" W x 12" D Shelving Unit

PARTS LIST

Your Basics 5-Tier Pantry Rack should include the following parts. Please inspect box contents to

ensure you have received all components.

You will NOT need additional tools for assembly.

DIVIDER (4)

A B

SHELF (5)

TOP POLE (4)

End Cap (4) and

Pole Connector (4)

pre-installed

BOTTOM POLE (4)

Threaded Insert (4)

pre-installed

D F

Note: The black circular plastic spacers in between Shelves are used only for packaging

purposes. They are NOT needed. Please discard.

ANTI-TIP

HARDWARE PACK

(1)

H I J K

LOCKING

CASTER (2)

WRENCH (1)NON-LOCKING

CASTER (2)

MIDDLE POLE (4)

Pole Connector (4)

pre-installed

PUSH HANDLE (1) SLIP SLEEVE

(44) + (4) extra

Summary of content (6 pages)

PAGE 1
PARTS LIST Your Basics 5-Tier Pantry Rack should include the following parts. Please inspect box contents to ensure you have received all components. You will NOT need additional tools for assembly.
PAGE 2
ASSEMBLY INSTRUCTIONS STEP 1 Screw each CASTER (H) and (I) into each BOTTOM POLE (A). Turn clockwise to screw in place. Make sure locking casters are on same side. Use provided caster wrench to tighten completely. Failure to do as instructed could result in caster stem breaking. A (4) H (2) I (2) J (1) A J H&I STEP 2 For easiest assembly, do NOT attach TOP POLES (C), MIDDLE POLES (B) and BOTTOM POLES (A) until instructed. Once connected, these will be posts for the rack.
PAGE 3
ASSEMBLY INSTRUCTIONS STEP 3 Place SHELF (D) on its side and slide each BOTTOM POLE (A) through each corner cylinder on SHELF (D). Make sure SHELF (D) corner cylinders are positioned over SLIP SLEEVES (G). D (1) Stand unit upright. Note: • Use a rubber mallet, if needed, to secure SHELF (D). • For convenience, place BOTTOM POLES (A) with Locking Casters on shorter side of shelf. D STEP 4 Screw MIDDLE POLE (B) into BOTTOM POLE (A). Repeat for each remaining MIDDLE POLE (B).
PAGE 4
ASSEMBLY INSTRUCTIONS STEP 5 In the same way as indicated in STEP 2 & 3, install 2 SHELVES (D) and then PUSH HANDLE (E). E G (36) D (4) E (1) Then install another 2 SHELVES (D) above PUSH HANDLE (E). Note: • PUSH HANDLE (E) height needs to be predetermined and assembled in right order. • Shelves are adjustable in 1” increments and can be placed as needed to best fit storage needs. • Use a rubber mallet, if needed, to secure SHELVES (D) and PUSH HANDLE (E).
PAGE 5
ASSEMBLY INSTRUCTIONS Anti-tip Hardware Installation ANTI-TIP HARDWARE PACK (K) is used to protect against accidental tipping – especially due to curious children. Note that installing ANTI-TIP HARDWARE PACK (K) will no longer allow your rack to be mobile. Washer (2) Anchor (2) Screw (2) K (1) On Wood Stud Determine wood stud location and mark it on wall, level with topmost shelf. Do this on two different studs along top shelf. Place Shelving Rack into position.
PAGE 6
SERVICE PARTS LIST Customer Service provides the following replacement parts: Part Number Description Part Number Description 1) ZSV-03-079-2412 Shelf 8) XXX-97-002-0005 Wrench 2) ZSV-04-047-1650 Top Pole 9) ZSV-02-012-0003 Divider 3) ZSV-01-029-1922 Pole Connector 10) XBK-01-011-1936 Slip Sleeve 4) ZSV-04-048-1800 Middle Pole 11) ZSV-05-028-1200 Handle 5) ZSV-04-049-1825 Bottom Pole 12) ZSV-02-011-0001 Anti-tip Hardware Pack 6) ZSV-99-007-2008 Non-locking Caster 13) XB