Installation & Assembly

ManualsBrandsDotted Line ManualsGarage & Outdoor Storage & OrganizationJill 56.5" H x 18" W x 18" D Shelving Unit

PARTS LIST

Your 5-Tier Square Rack should include the following parts. Please inspect box contents to ensure you

have received all components.

You will NOT need additional tools for assembly.

SIDEBAR W/

HOOKS (1)

A B

SHELF (3)

TOP POLE (4)

End Cap (4) and

Pole Connector (4)

pre-installed

BOTTOM POLE (4)

Threaded Insert (4)

pre-installed

D F

Note: The black circular plastic spacers in between Shelves are used only for packaging

purposes. They are NOT needed. Please discard.

ANTI-TIP

HARDWARE PACK

(1)

G H I J

WRENCH (1)LOCKING

CASTER (4)

MIDDLE POLE (4)

Pole Connector (4)

pre-installed

BASKET (2)

SLIP SLEEVE

(42) + (4) extra

Summary of content (6 pages)

PAGE 1
PARTS LIST Your 5-Tier Square Rack should include the following parts. Please inspect box contents to ensure you have received all components. You will NOT need additional tools for assembly.
PAGE 2
ASSEMBLY INSTRUCTIONS STEP 1 A (4) Screw each LOCKING CASTER (H) into each BOTTOM POLE (A). Turn clockwise to screw in place. Use provided caster wrench to tighten completely. Failure to do as instructed could result in caster stem breaking. H (4) I (2) A I H STEP 2 For easiest assembly, do NOT attach TOP POLES (C), MIDDLE POLES (B) and BOTTOM POLES (A) until instructed. Once connected, these will be posts for the rack. Note that POLES (A+B+C) have slight horizontal line indentations at 1” intervals.
PAGE 3
ASSEMBLY INSTRUCTIONS STEP 3 Place SHELF (D) on its side and slide each BOTTOM POLE (A) through each corner cylinder on SHELF (D). Make sure SHELF (D) corner cylinders are positioned over SLIP SLEEVES (G). D (1) Stand unit upright. D Note: • Use a rubber mallet, if needed, to secure SHELF (D). STEP 4 In the same way as indicated in STEP 2 & 3, install BASKET (E). Note: • Use a rubber mallet, if needed, to secure BASKET (E).
PAGE 4
ASSEMBLY INSTRUCTIONS STEP 5 Screw MIDDLE POLE (B) into BOTTOM POLE (A). Repeat for each remaining MIDDLE POLE (B). B (4) C (4) F (1) G (26) C Screw TOP POLE (C) into MIDDLE POLE (B). Repeat for each remaining TOP POLE (C). B Note: Top of each TOP POLE (C) is indicated by a BLACK END CAP. STEP 6 In the same way as indicated in STEP 2 & 3, install 1 BASKET (E), 2 SHELVES (D) and then 1 SIDEBAR W/ HOOKS (F) as desired.
PAGE 5
ASSEMBLY INSTRUCTIONS Anti-tip Hardware Installation ANTI-TIP HARDWARE PACK (J) is used to protect against accidental tipping – especially due to curious children. Note that installing ANTI-TIP HARDWARE PACK (J) will no longer allow your rack to be mobile. Washer (2) Anchor (2) Screw (2) J (1) On Wood Stud Determine wood stud location and mark it on wall, level with topmost shelf. Do this on two different studs along top shelf. Place Shelving Rack into position.
PAGE 6
SERVICE PARTS LIST TRINITY Customer Service provides the following replacement parts: Description Description 1) Shelf 2) Sidebar w/ Hooks 3) Top Pole 4) Pole Connector 5) 6) Middle Pole Bottom Pole 12 7) Locking Caster 8) Wrench 9) Basket 10) Slip Sleeve 11) Anti-tip Hardware Pack 12) End Cap 1 2 11 3 10 4 5 9 8 6 7 6