Brochure

30
[phone]
■
dormont.com
LV BLACK COATED GAS CONNECTOR SPECIFICATIONS
DesignCerticationsandApprovals
• ANSI Z21.24/CSA 6.10 – Connectors for Gas Appliances
• ANSI Z21.75/CSA 6.27 – Connectors for Outdoor Appliances
and Manufactured Homes
• City of New York – MEA #376-92-M
• Approved by the Commonwealth of Massachusetts Board of
State Examiners of Plumbers and Gas Fitters – connector length
may not exceed 36"
FeaturesandSpecications
• Tubing Annealed, 304 stainless steel (ASTM A240)
• Black coating. Maximum temperature rating: 350°F
• Flare nuts Brass or steel with black plated steel
• Adapters Brass or steel with black plated steel
• Approved for indoor and outdoor use
• Designed for high-temperature applications up to 350°F.
• 100% factory leak tested.
• When installing a new appliance or when an existing appliance
is moved to a new location a NEW gas connector must be used
per manufacturer’s installation instructions and per product
standards ANSI Z21.24/CSA 6.10 and ANSI Z21.75/CSA 6.27.
• Avoid repeated bending, flexing, or extreme vibration. Do not use
on portable gas generators due to excessive vibration
Connector Minimum Flow Capacity – For Natural Gas
(per ANSI Z21.24/CSA 6.10 & ANSI Z21.75/CSA 6.27)
Straight Length Capacity – BTU per Hr 0.64 SG., 1000 BTU per Cu. Ft.
at 0.5 inch Water Column Pressure Drop
Series Nominal
OD (in)
Nominal
ID (in)
12" 18" 24" 30" 36"
10A 3/8" 1/4" 48,000 43,800 40,000 36,400 33,400
20A 1/2" 3/8" 102,000 93,100 85,000 77,100 71,100
• Coating reduces glare and
hides the connector from
view
• Black adapters and flare nuts
further reduce visibility of the
connector
• Black coating withstands up
to 350°F
• Exclusive No-Neck
®
design
provides protection against
stress fractures
• More corrugations per inch
increase flexibility and extend
service life
Specifically engineered for high-temperature
applications such as gas logs, fireplace inserts,
and free-standing fireplaces
• Designed to reduce glare and hide the connector from view to
enhance the beauty of the hearth.
• Hi-temperature black coating hides the connector while with-
standing up to 350°F.
• FLARE adapters and flare nuts are plated with black to further
reduce the visibility of the gas connection.
Connector Minimum Flow Capacity – For Propane Gas
(per ANSI Z21.24/CSA 6.10 & ANSI Z21.75/CSA 6.27)
Straight Length Capacity – BTU per Hr 1.55 SG., 2500 BTU per Cu. Ft.
at 0.5 inch Water Column Pressure Drop
Series Nominal
OD (in)
Nominal
ID (in)
12" 18" 24" 30" 36"
10A 3/8" 1/4" 76,800 70,080 64,000 58,240 53,440
20A 1/2" 3/8" 163,200 148,960 136,000 123,360 113,760
All installations must completely comply with all Dormont
manufacturing company warnings and instructions, nation-
al, state and local codes and all applicable ansi standards.
LV Black Coated
GasConnectorSpecications
NOTICE
When using 0.2 water column pressure drop, capacity can be determined by multiplying the values above by 0.632 (for both natural and propane gas).
For capacities at other than noted, contact Dormont at 1-800-DORMONT.
FIP endMIP end
WARNING
!