User Manual

THE USER SHOULD NOT ATTEMPT TO SERVICE
OR REPAIR THE MONITOR. ALL SERVICING
SHOULD BE REFERRED TO CONSUMER CARE AT
www.safety1st.com/monitorsupport.
It is essential to check reception regularly.
Features & Components
Please read the following instructions and
warnings carefully. Keep these instructions for future
reference. No batteries needed. Tools required for mounting
camera: Phillips screwdriver and drill with 3/16” size bit.
User’s Guide
MO160
HD Wi-Fi Baby Monitor
Set Up
Plug In Camera
• Connect the micro USB power cable with power adapter to camera’s port.
• Plug the power adapter into a suitable wall socket.
• Wait for the Camera LED to blink purple.
Install Smart App
Download the Safety1
st
App by searching for Safety1
st
in the app store. You can also
visit www.safety1st.connected/apps in any browser on your smart device.
Note: If you already use the Safety1
st
App, make sure that you are using the latest
version. To nd out if an update is available, review the settings within the app or go to
the App store and search for Safety1
st
.
Setup
In your smart device, follow the screens in the Safety1
st
App for setup at
www.safety1st.com/apps .
Resetting Camera
If you have Camera setup issues, then the Camera may need to be reset.
If you received your camera from a friend/family or other third party the camera should
be removed from their account before attempting to setup the camera with your
account.
Please reset the Camera with the following procedures:
1. Find a paperclip or similar tool.
2. Insert the tool straight into the reset button hole.
3. The button will compress and you will hear a subtle click
4. Hold the button down for at least 3 seconds.
5. Release the button and wait for the camera to reboot.
6. The process is complete when the light is solid red.
7. You can add your Camera again by following the steps within the app.
Using your Baby Monitor
Note: Explore the features and functionality within the Safety1
st
App. Use the in-app
tutorial to help guide you where required.
Position Baby Monitor
Wall Mount
1. Mark the location on the wall where the camera will be
mounted.
2. Using a 3/16” drill bit drill a hole 1.0” (2.54 cm) deep.
3. Insert drywall anchor into hole. Lightly tap with a hammer
if necessary until the drywall anchor is ush with the
wall surface.
4. Using a screwdriver, hand screw a screw into the
drywall anchor leaving approximately 0.25” (0.63
cm) sticking out.
5. Insert the key hole on the base of the camera onto
the screw on the widest part.
6. Slide the camera DOWN on the screw locking the
camera into place. DO NOT slide the camera UP as
this will result in the camera falling off of the wall.
7. Use the provided wall clips to position and secure the cord 3 ft (0.9 m) away from
the crib. Repeat steps 2, 3 and 4 to place the wall anchors into the wall. Place each
wall anchors 2 ft (0.61 m) apart.
8. Place cords into the wall clips and pull tightly to align wall clip hole to wall anchor.
9. Close the top cover to secure the cord in place and insert provided screw and tighten
into wall anchor.
Table Top
1. Determine camera location keeping the camera at least 3 ft (0.9 m) away from crib.
The Camera should be placed on a at surface, such as a chest of drawers, desk or
shelf.
2. Use the provided wall clips to position and secure the cord 3 ft (0.9 m) away from
the crib.
App Upgrade
You can nd the latest version of Safety1
st
App by visiting your mobile device’s app
store (e.g.: iTunes App Store, Google Play). From there, you can see what’s new with
the app and install the latest version.
Occasionally, Safety1
st
will send you notications that a newer version of the Safety1
st
app is now available. While some of the upgrades simply keep your system running
efciently, some are critical to system functionality. We strongly recommend that you
complete the upgrade as soon as possible. Software upgrades will only be performed
in Wi-Fi mode.
Wi-Fi Connectivity
Check the Wi-Fi signal strength from your internet service provider.
To avoid signal interference or echoes, ensure that there is enough distance between
your device and the Camera. Use of other 2.4GHz products, such as Bluetooth systems
or microwave ovens, may cause interference with this product. Also avoid placement
near major electrical equipment, large metal or concrete objects or walls. Keep the
Camera at least 5 ft (1.5 m) away from these types of products, or turn them off if they
appear to be causing interference.
Troubleshooting
A blinking red light on your camera or parent unit indicates that your unit is discon-
nected from Wi-Fi. Check your Wi-Fi connection.
A solid purple light on your camera or parent unit indicates the unit needs to be paired.
To pair, press and hold the Pairing Button.
A red solid light on your parent unit indicates the battery is low.
Visit www.safety1st.com/monitorsupport for frequently asked questions and
video references. If your product is not working properly consult the quick start guide
or owners manual. Check your internet service connectivity. Check online FAQ and
community at safety1st.com/monitorsupport Tap the In-App support icon on
your smart device.
1 Year Warranty
Dorel Juvenile Group will replace or repair (at our option) your unit free of charge
from 12 months from the date of purchase if the unit is defective in workmanship
or materials. To make a claim, contact Consumer Care at 1-800-544-1108 or text
us at 812-566-2525 within one year of purchase from an authorized retailer. Please
be prepared to validate proof of purchase with your claim In the absence of a
purchase receipt, the warranty will be considered 12 months from the date of prod-
uct manufacture. This warranty does not apply to normal wear or damage from
misuse, abuse, improper storage and handling, installation, accident, unauthorized
repair or alteration, tampering, contact with liquid, water, rain, extreme humidity,
sand, dirt, extreme heat, placement or testing not in accordance with the user guide
placement or testing not in accordance with the user guide. Please contact our
Consumer Relations department for more details.
General Information
Baby Monitor Care
Cleaning
Clean your Camera with a slightly damp cloth or with an anti-static cloth. Never use
cleaning agents or abrasive solvents.
Do not clean any part of the product with thinners or other solvents and chemicals
- this may cause permanent damage to the product which is not covered by the
warranty.
Keep your Camera away from hot, humid areas or strong sunlight, and do not let
it get wet.
Every effort has been made to ensure high standards of reliability of your Camera.
However, if something does go wrong, please do not try to repair it yourself -
contact Customer Service for assistance.
Disposal
At the end of the product life cycle, you should not dispose of this product with
normal household waste. Take this product to a collection point for the recycling of
electrical and electronic equipment.
Some of the product materials can be re-used if you take them to a recycling point.
By reusing some parts or raw materials from used products you make an important
contribution to the protection of the environment.
Please contact your recycling center in case you need more information on the
collection points in your area.
WARNING!
Strangulation Hazard - Children have
STRANGLED in cords. Keep cords
out of reach of children more than
3 feet (0.9 m) away. Use Wall clips
provided to secure cord away from
baby’s reach. Only use the AC adapter provided by
the manufacturer. NEVER use an extension cord
with the AC adapter.
Microphone - For
audio input
Status LED Indicator -
Shows the camera status
Lens - Provides a
clear, wide angle
view
IR LED - Turns on/off
night vision automatically
Set Button - Press and
hold 3 seconds
Reset Hole
Reset the camera
Speaker
Swivel Joint - Tilt the
camera to maximize view
Micro USB Charging Port
Camera Power Cord –
3m (10ft)
Mounting Slot - Attach
the camera to screws
Rubber Base - Increases
friction to x camera on
smooth surface
Home & System Requirements
• Wireless internet (Wi-Fi) with >1mbps
download/upload speeds
• Smart phone or tablet
• Check your phone capability at
www.safety1st.com/devicecheck
which will direct you to the app store and our app
Screws (7)
Drywall anchors (7)
Wall clips (5)
Monitor uses encrypted transmission over FCC managed
frequencies. Always remember to password protect your
Wi-Fi router.
IMPORTANT SAFETY INSTRUCTIONS
• VENTILATION: DO NOT block ventilation openings. DO NOT place on a bed,
sofa, rug or similar surface. DO NOT place in a book case or cabinet that may
restrict air ow.
• HEAT: The Monitor should be situated away from heat sources such as radia-
tors, heat registers, stoves, or other appliances that produce heat. Also keep
these components out of direct sunlight.
• POWER CORD PROTECTION: The power supply cord should be routed so that
it is not likely to be walked on or pinched by items placed upon or against it. Pay
particular attention to the cord at the plug, convenience receptacle, and at the
point it exits from the Monitor.
FCC/IC Information
CAUTION: 1. To comply with FCC RF exposure compliance requirements, a separation
distance of at least 20 cm must be maintained between the antenna of this device and
all persons. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 15 of the FCC Rules. These Limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning this equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modications not expressively approved by Dorel Juvenile
Group can void your authority to operate this equipment under Federal Communica-
tions Commission’s rules.
Use of other accessories may not ensure compliance with the FCC exposure guide-
lines.
IC Information
This device complies with Industry Canada license-exempt RSS standard(s). Opera-
tion is subject to the following two conditions: (1) this device may not cause interfer-
ence, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using
an antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
This Class B digital apparatus complies with Canadian ICES-003.
WARNING!
STRANGULATION HAZARD -
Children have STRANGLED in cords.
Keep cords out of reach of children
(more than 3 feet (0.9 m) away). Use
Wall clips provided to secure cord
away from baby’s reach. Only use the AC adapter
provided by the manufacturer. NEVER use an exten-
sion cord with the AC adapter.
• For indoor use only. To reduce the risk of re or
electrical shock, DO NOT expose this product to
water or moisture. DO NOT use monitor near water
(such as bath tub, sink, etc.) or submerge in water.
• This monitor is not intended to be used as a medi-
cal monitor and its use should not replace proper
adult/parental supervision. You should check your
child’s activity at regular intervals as this moni-
tor will not alert parents to the silent activities of a
child.
• NEVER attempt to disassemble the product. This
is dangerous and will void the warranty.
• Test monitor periodically when in use and chang-
ing locations.
• Use only the adapter supplied with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
• To prevent entanglement and overheating, DO
NOT use extension cords.
• The adapter may become slightly warm to the
touch during operation. This is normal.
• ALWAYS unplug the AC adapter from the wall dur-
ing extended periods of non-use.
• Check to make sure wall outlet plates are not
unusually hot to the touch. If they are, immediately
unplug cords from these outlets. Check that all
outlet connections are in good condition so that
adapter is not loose or that no wiring is exposed.
Have a qualied, licensed electrician or that no wir-
ing is exposed.
• This baby monitor allows internet users to hear or
view activity. Use the security feature included with
this device to restrict internet viewership.
• DO NOT place adapter/wall plug under a window
where a child might use it to step on and/or to
reach something that might be dangerous.
• Adult assembly is required. Keep small parts away
from children when assembling. Exercise care when
unpacking the product.
• This product is not a toy. DO NOT allow children
to play with it.
3’ (91.4 cm)
Top Wall
(left side) (right side)
© 2017 Dorel Juvenile Group, Inc. Safety 1st
TM
and the Safety 1™ logo and
design are trademarks of Dorel Juvenile Group, Inc.
www.safety1st.com/monitorsupport Styles and colors may vary. Los estilos y
los colores pueden variar. Made in CHINA. Hecho en CHINA.
Distributed by (distribuido por) Dorel Juvenile Group, Inc., 2525 State
St.,Columbus, IN 47201-7494.
Dorel Juvenile Canada, 2855 Argentia Road, Unit 4, Mississauga, ON, L5N 8G6
09/19/17 4358-xxxx
Importado y Distribuido en Chile por: Comercial e Industrial Silfa S.A. - San Ignacio 0201 / Parque Industrial Portezuelo
Quilicura, Santiago Chile. Fono (562) 2339 9000. En Perú por: Comexa S.A. - Los Libertadores 455 – San Isidro, Lima
– Perú. Fono (511) 4469014. En Centro América, Caribe y Ecuador por: Best Brands Group S.A. – Av. Balboa, Bay Mall
Plaza, Planta Baja, local 9, Panamá. - Fono: [phone]. En Colombia por: Baby Universe S.A.S. - Vía 40 No. 77-29,
Barranquilla, Colombia - Fono: [phone]
Importador: DJGM, S.A. DE C.V. Gabriel Mancera No. 1041 Col. Del Valle Delegación Benito Juárez C.P. 03100
México, D.F. R.F.C. DJG140305GN9 Tel. [phone]