Owner's Manual
Wheel Loader
SD310
No. 108 8 , Xinche ng Stre e t. Muping Economic De ve loping Zone
Yantai Shandong 26 4 100 China
Te l: + 8 6 -10-8 4 54 -7075 Fax: + 8 6 -535-470-74 31
17,300
38,140
3.0
3.9
5000
17
161
36,194
30
3085
10'1"
1,297
4'2"
8260×2992×3450
Doosan DE08TIS (TIER-II Certified)
TURBO, DIRECT INJECTION
6
111 X 139 (mm)
902 N.m/1300 rpm
160kW(215HP)/2,000 rpm
2000 rpm
215 g/kw.h @ RATED SPEED
Single Stage, Single phase,
Three elements(single turbine)
2.142
4 SPEEDS, POWER-SHIFT,
COUNTERSHAFT
4 forward shift , 3 back
38.0 KPH
kg
lb
m3
yd3
kg
Ton
kN
lbf
Degree
mm
ft in
mm
ft in
mm
km/h
Overall working weight
Capacity heaped ISO/SAE
Rated load
Max traction force
Max breakout force (kN)
Max gradability
Dump height (at 45º) 1)
(at fully raised)
Dump reach (at 45º) 1)
(at fully raised)
Overall dimension(LxWxH)
Model
Type
Number of cylinder
Bore/stroke (mm)
Max torque
Rated power
Rated speed
Min fuel consume ratio
Torque converter type
Torque ratio
Transmission type
Gear shift
Max speed
Front and Rear Axles
Brake system
FULLY FLOATING PLANETARY-TYPE
HUB DRIVE
FIXED MOUNTING(FRONT)
TRUNNION MOUNTING(REAR)
PLANETARY
23.5 -25-16PR
0.38
0.34
Gear
40
5800
19'0"
6510
21'4"
170
< ~ 6.0
< ~ 11.3
AIR PUSH HYDRAULIC
SINGLE LINE
SPRING-APPLIED
AIR RELEASED DRUM BRAKE
330
177
Mpa
Mpa
degree
mm
ft in
mm
ft in
bar
sec
sec
liter
liter
TYPE
Final decelerate type
Tyre specification
Front tyre pressure
Rear type pressure
Type
Steering angle
Min. turning radius
(outside tires)
Min. turning radius
(outside bucket)
System working pressure
Boom lifting(full load)
Total time
Service brake
Parking brake
Fuel
Hydraulic oil
Engine
Transmission system
Tyre
Steering System
Hydraulic system
Fill capacity
I
J
K A
G
F
H
L
M
N
E
D
C
B
R
S
T
Q
O
P
Dimension
1) Measured to the tip of the bucket teeth or bolt-on edge. 2) SD310: All measurements with tyres 23.5-25-16PR(L3)
K. Dump height (at 45º) 1)
(at fully raised)
L. Maximum rollback at ground
Max. tilt angle at ground
M. Hinge pin height at carry position
N. Maximum digging depth
O. width over tires
P. Tread width
Q. turning radius outside tires
R. Maximum steering angle (each side)
S. Bucket width
T. Turning radius outside bucket
mm
ft in
degree
mm
mm
ft in
mm
ft in
mm
ft in
mm
ft in
degree
mm
ft in
mm
ft in
3085
10'1"
45
500
120
5"
2750
9'2"
2150
7'0"
5800
19'0"
40
2992
9'9"
6510
21'4"
A. Height to top of cab and canopy
B. Ground clearance
C. Machine center point to rear axle
D. Wheel base
E. Overall length
F. MAX. TILT ANGLE (fully raised)
G. Bucket dump at full height
H. Dump reach (at 45º) 1)
(at fully raised)
I. Maximum overall height
J. Hinge pin height at full lift
mm
ft in
mm
ft in
mm
ft in
mm
ft in
degree
degree
mm
ft in
mm
mm
ft in
3450
11'3"
420
1'37"
1600
3200
10'6"
8260
27'1"
60.5
49
1297
4'2"
5713
4150
13'7"
※Specificatiions are subject to change without notice for quality improvement.
Spe cification
Dime ns ion
https://www.tractormanualpdf.info/