Installation and Operating Manual Operator SWING-3000/5000
Contents 2. General information................................................................................................................3 2.1 Extent of use..................................................................................................................3 2.2 Specifications.................................................................................................................3 3. Delivery set......................................................................................
General Information 2. General Information The electromechanical linear operator produced by the company DoorHan is intended for automation of a street double-leaf swinging gate with the load-bearing structure. The body of the operator consists of 2 silumin parts, in which a motor, a reducer and a lead screw are positioned. The operator is equipped with built-in electrical end switches for opening and closing.
Safety instructions 4. Safety instructions For safe operation of the automated gate, do observe these installation instructions. • Incorrect installation can cause serious damage to persons and property. • Before installation read carefully this manual. • Do not make any modifications in the automated system, which are not mentioned in this manual. • The operator SWING is intended for automation of swinging gates. Do not install the operator for uses other than indicated in this manual.
SAFETY AT INSTALLATION SAFETY AT INSTALLATION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 5 ATTENTION! Read carefully these instructions, incorrect installation and improper use of the operator can cause injury of people. Before installation read carefully this manual. Remove the packing of this product and dispose of it. Do not leave the packing material within reach of children.
Tools 5. Tools 1 2 3 1. 2. 4 3. 4. 5. 6. 7. 8. 5 6 7 Set of spanners Set of screwdrivers for crosshead and cut-head screws Set of metal drills Set of concrete drills Flat-nose pliers Metal hacksaw Electric drill Folding rule 8 6. Operator Components Swing 3000 793 300 Stroke Nut M8 720 Swing 5000 Stroke 1. 2. 3. 6 Operator Front bracket Rear fork 4. 5. 6.
Installation 7. Installation Before installation make sure, that the gate move free and it is possible to fasten reliably the operator on the pole and the leaf. Installation of the operator is shown below: 7.1 Inward Gate Opening Attention! Make certain, that the dimension C does not exceeds the value indicated in the table. Otherwise it is necessary to improve the pole according to the indicated dimension value.
Outward opening of gate with operator SWING-5000 7.2 Outward opening of gate with operator SWING-5000 1) Measure dimensions A and B 2) Install and fasten the rear bracket on the pole using an additional bracket. 3) Open the gate, measure distance E and fasten the front bracket on the gate leaf. 130 B 130 Е 720 E А B External side of the object Internal side of the object Additional bracket A 8.
Control Unit Description 8.2 Control Unit Description Basic programming To go into the basic programming mode, press the key F. On the left display you will see name of the function, which is to be programmed and on the right display you will see current value of this function. The value can be changed by pressing keys + or -. If you press the key F again, you will see on the display the name of the next function and you will be able to program this and so on.
OPERATOR PROGRAMMING 14-15. CL FOTO – Contacts for connection of closing safety device (NC): these connections are used for protection from pinching people, animals and other objects in the gate aperture when leaves are closing. Response of the devices during operating the gate causes reverse movement of the gate leaves or immediate stop and follow-up reverse movement, if it is adjusted. Response of the devices, connected to these terminals does not effect operation of the automatic system during opening.
Advanced Programming Advanced Programming In order to go into ADVANCED PROGRAMMING mode, press the key F and holding it down, press the key +. You will see the name of the function to be programmed. On the right display you will see the current value of the function, which can be changed by pressing the keys + or -. If you press the key F repeatedly, you will se on the display the name of the next function and you will be able to program it.
Closed Position 10.3 Closed Position: 1. View A Put the gate leaf in fully closed position, which can be determined by the mechanical stop. Unscrew fastening of the closing microswitch. Move the end microswitch along the guide until the microswitch contacts with the slide. Move the microswitch ahead until the microswitch finger leaves response area. Fix the microswitch. 2. 3. 4. 5.
TROUBLESHOOTING 13. Troubleshooting Symptom Operator does not run Possible reason Solution Power is off. Make sure, that the power is on. Obstruction at gate’s movement Remove the obstruction. Bad wiring connection Check reliability of electric wiring connection. Operator is released Engage the operator. Operator stops suddenly. Thermal protection is active. Let the operator cool. The gate does not open or close in full. Wrong adjustment of end switches. Adjust the end switches.
Notes 14 I n s t a l l a t i o n a n d O p e r a t i n g M a n u a l O p e r a t o r S W I NG - 3 0 0 0 / 5 0 0 0
NOTES 15 I n s t a l l a t i o n a n d O p e r a t i n g M a n u a l O p e r a t o r S W I NG - 3 0 0 0 / 5 0 0 0 15
The company DoorHan thanks you for buying our products. We hope you will be satisfied with the quality of our product. If you need any further information about purchasing, distribution and maintenance, contact our regional agents or refer to our central office to the following address: Russia, 143002, Moscovskaya oblast, Odintsovskiy r-n, s. Akulovo, ul.Novaya, 120. Tel: +7(495)933-2400, 981-1133 E-mail: Info@doorhan.com www.doorhan.
