V20221009 Sliding Gate Opener User Manual 1400LB / 600KG
CONTENTS Safety Notice Parts List Technical Parameters Installation Others
Dear user: Thank you for choosing our product. Please read this manual carefully before assembly and use. Please do not forget to include this manual if you send this product to a third party. SAFETY NOTICE Please ensure that your power voltage matches with the supply voltage for the gate opener (110V AC) before installation. The installation and maintenance of this product and its components must be carried out by trained professionals to ensure safety and safe use.
PACKING LIST (STANDARD) No. Picture Name Quantity 1 Main engine 1 2 Manual release key 2 3 Remote control 2 4 Mounting accessories box 1 4-1 Sprocket cover 1 4-2 Chain link 2 4-3 20 ft.
No. Picture 4-11 Name Quantity Inner M6 20 mm bolt 4 M6 65 mm bolt 4 M8 25 mm bolt 4 M6 nut 16 M8 nut 16 φ6 flat washer 16 φ8 flat washer 16 φ6 spring washer 16 φ8 spring washer 12 4-12 4-13 4-14 4-15 TECHNICAL PARAMETERS Maximum weight of gate 1400 lb (600 kg) Power supply 110V/60Hz Motor power 180W Gate moving speed 39.36 ft./min. Remote control distance ≥98.4ft.
INSTALLATION This sliding gate opener works with gates weighing less than1400 lb (600 kg) and measuring less than 30 ft. in length. The drive mode uses a sprocket and chain transmission. This gate opener must be installed inside the enclosure or yard to prevent tampering with the device.
Size of mounting base 276 310±0.3 Detachable mounting base One-piece mounting base Figure 3 Installation Procedures Preparation work before installation Please ensure that the sliding gate is correctly installed, the gate rail is horizontal, and the gate can glide back and forth smoothly when moved manually before installing the gate opener.
Main engine installation Dismantle the plastic housing on the main engine before installation. Keep its fasteners handy.
Chain installation Close the gate. Connect the tie rod with the chain using its chain link; fasten the tie rod to the door connecting plate with washers and nuts as shown in Figure 8. If necessary, the elasticity of chain can be adjusted through the tie rod at both ends and the chain can be shortened. If it needs to be lengthened, make sure to use the same type of chain so it moves easily but securely.
Installation of sprocket cover is shown in Figure 11: Cross screw M4×10 Sprocket cover Figure 11 The distance between main engine and chain ends should be at least 11.8 in. (30 cm), as shown in Figure 12: ≥30CM Figure 12 Warning To ensure safety, install safety stop blocks on both ends of the rails to prevent the gate from getting out of the rail.
≤20mm Main engine Magnet Magnetic limit switch block Gate Chain Magnet Chain wheel Gate Magnetic limit switch block Nut M8 Spring washerφ8 Flat washerφ8 Chain Figure 13 Figure 14 Note: The default setting is right side mounting. (Please refer to “Adjustment and operation” in 4.3.5 for adjustment instructions.) Control Board Connections and Indicators Diagram Figure 15 Open/Close: Light indicators for gate movement direction. When OPEN is on, the gate should be opening.
Features ● Pair with up to 20 different 433.92 MHz remote controls and with wireless keypads. ● Compatible with and easily connected to alarm lamps, external control buttons, and infrared photocell sensors. ● Auto-close functionality for improved security. Gate Opener Installation Step 1 Ensure your gate can glide back and forth smoothly by hand before installing the gate opener.
DIP Switches The DIP switches on the control board control the external buttons control mode and the auto-close time settings.
PACKING LIST (STANDARD) Maintenance For the sake of safety, each gate should be equipped with an infrared protector, and regular inspection is required. You should check whether your device operates normally at least every month. Troubleshooting Problems Possible Reasons Solutions The gate cannot open or close normally, and LED light does not flash. 1. The power is off. 2. The fuse is burned. 3. There is a problem with the control board power wiring. 1. Turn on/connect the power supply. 2.
