User's Manual

ManualsBrandsDongguan Jin wen hua digital technology ManualsAudio EquipmentBluetooth Speaker

Table Of Contents

页 1

1 2

1.Volume down/Previous Track

2.Volume up/Next Track

3.Play/Pause/Answer/End call

4.Power Button

5.Aux In Port

6.USB Output Port

7.Micro USB Charging Port

8.Microphone Adjust Button

9.Microphone port

10.Line in Light(Red)

11.Charging LED Light(Red)

12.Bluetooth LED Light(Blue)

1211 10

Model:AOMAIS Go

Size:13.39 * 3.94 * 6.69 inch

Weight:61.73 Oz

Bluetooth version:V4.2

Waterproof Rating:IPX7

Battery capacity:7200 mAh lithium battey

Audio output:15W * 2

Range:10m/33ft

Input:5V/2A

THD:1% Volume max

Charging time:4 hours

Play time:7 hours(60% volume)

Charging the Battery

Low Charge Remaining Indicator

.When the battery running low the charging led light(Red) will begin slowly ﬂashing and will remain ﬂashing until the speaker is

turned off.

.The volume will decrease to preserve the remaining battery charge.

Fully Charged Indicator

.Solid red light indicates that speaker is charging, once the speaker is fully charged the red led light will turn off, power

indicator will turn green

Note:Please remember to close the USB and Aux port cover when not charging. The cover need to be closed to keep spaker

waterproof.

Playing while Charging

You can play the AOMAIS Go II while it is charging

Charing the Devices

AOMAIS Go can use as power bank, can charging your smartphone, Tablet, Bluetooth speaker or others

Turn On and Turn Off

.Turn on: Press and hold the power button to turn the speaker on/off.

Flashing blue led light indicates that the speaker is on and with voice prompts “power on”.

.Fast ﬂashing Blue: Indicators speaker is in pairing mode

.Slowly ﬂashing Blue: Indicators speaker is connected to a source device and ready to play

Pairing & Connecting

A:Bluetooth Mode

.Make sure your AOMAIS Go battery is full charge. Your source device needs to be within 33 unobstructed feet the AOMAIS Go

.If the blue led light is fast ﬂashing after turn on, indicator the AOMAIS Go is ready to pair and connect, also with the voice

prompts “Ready to Pair”.

.If the blue light is slowly ﬂashing and voice prompts “Paired”the .AOMAIS Go has automatically reconnected to the last source

device the speaker was connceted to and is ready to play.

Note: AOMAIS Go will automatically try to connect to the last source device it was connceted to each time it is turned on and that

source device is within range.

.AOMAIS Go can be connected to one device at a time.

To pair or connect to different source device, you need to disconnect the currently paired device. To disconnect it, press and

hold the Play/Pause button. The blue light will begin ﬂashing and will announce “Ready to pair”.

B:Audio Cable Mode

You can playing your Apple Mac, Laptop, Computer and non-Bluetooth devices with the 3.5mm audio cable. Like some older

Windows computers and operating systems may have difﬁculty pairing and connect over Bluetooth. If this occurs it is

recommended to connect using 3.5mm audio cable.

Note: The Bluetooth on the AOMAIS Go is disabled when the 3.5mm audio cable is connected to the speaker

.Please remember to close the USB and Aux port cover when not using 3.5mm audio cable. The cover need to be closed to keep

spaker waterproof.

Wireless Hands Free Personal Speakerphone

To answer and incoming call/To end a call

Press and release the phone button, same action for hanging up

To reject an incoming call

.Press and hold down the phone button for 2 seconds

.The wireless hands free personal speakerphone feature works over Bluetooth with smartphones for phone calls only

.Please keep the speaker close in front of you so you may be heard clearly by the listener

AOMAIS Go Stereo Pairing Guide

.Bring two AOMAIS Go speakers within 1m(3ft) from each other. Turn on both speakers. Flashing blue light indicates that

speaker is ready to be paired.

.Press and hold two volume buttons of one speaker until you hear a beep. Then you will hear “paired”, which means the

connection between the speakers is established.

.Start playing music on your device and adjust volume to a desirable level, both speakers have the same function after being

paired, you can control both speakers through one of them.

.If you want to disconnect the two speakers, press and hold two volume buttons on one speaker until you hear a beep,

afterwards you will hear “ready to pair”. The two speakers are now disconnected and can be used as single unit.

.Your Bluetooth device may be out of range, move closer within 30 unobstructed feet

.Turn your AOMAIS Go off and back on

No audio playing from the speaker when connected with the 3.5mm audio cable

.Make sure the 3.5mm audio cable is fully inserted the AOMAIS Go and device.

.Make sure your device is on and playing music

.Increase the volume level on the AOMAIS Go and device

Poor sound quality when connected over Bluetooth

.Your Bluetooth device may be out of range, move closer within 30 unobstructed feet

.Remove the AOMAIS Go from the Bluetooth device list on you source device, and then re-pair and conncet to the speaker.

.Turn your AOMAIS Go off and back on

.Some devices need to have their WIFI turned off to improve audio quality over Bluetooth

Poor sound quality when connected within the 3.5mm audio cable

.Reduce the volume level on the AUX source

.Remove the charging cable while playing

Customer Support:support@aomais.com

.12-month limited warranty .Lifetime technical support

Troubleshooting & Customer Support

For assistance with the questions or any issue with your AOMAIS Go that is not answered in the troubleshooting tips below,

please contact us by visiting: aomais.com/contact and sent the mail to our customer service

Can not turn on

.The battery may have become fully drained. Charge the AOMAIS Go use wall charger from a Smartphone/iPhone, then press

the power button to turn the speaker on. Then continue charging the battery

.Reset the AOMAIS Go

Can not pair or connect to Bluetooth

.Check the Bluetooth led light (Blue) to make sure it is quick ﬂashing. If it is slowly ﬂashing blue light the AOMAIS Go is already

connected to another source device.

.The speaker can be paired with only one device at a time. Meaning if you would like to pair the speaker with a second different

device, you must cut off the pairing between device and the speaker. Please see the instructions on page5

.Check that your AOMAIS Go has a sufﬁcient battery charge, the speaker may not connect when the battery has a low charge.

Connect the speaker to a charging source and try again pair and connect

.Your device may be out of range. Move it closer to within 33 unobstructed feet of your speaker

.Some older windows computers and operating systeams may have diffculty pairing and connceting over Bluetooth. If this

occurs it is recommended to connect using the 3.5mm audio cable.

No audio playing from the speaker when connceted over Bluetooth

.Remove the AOMAIS Go from the Bluetooth device list on you source device, and then re-pair and conncet to the speaker.

Safety and Precautions

.Follow all instructions - All operating and use instructions should be followed.

.If not use the device for long time, to protect the battery life, please full charge the Speaker and keep it always powered

.Do not recommened to fully submerged, which will lead to no sound under the water due to signal cut off

.Protect the Micro USB charging cable from pinched particularly at the connectors.

.Unplug the USB charging cable during storms or when unused for long periods of time.

How to use the microphone ?

insert your your microphone into the microphone audio jack

In the package........................................................................................................................................................1

Button and Connectors............................................................................................................................................2

Speciﬁcations.........................................................................................................................................................3

Charging the Battery................................................................................................................................................4

Turning On and Off..................................................................................................................................................5

Wireless Hands Free Personal Speakerphone...........................................................................................................5

Pairing & Connecting...............................................................................................................................................6

IPX7 Waterproof.....................................................................................................................................................7

AOMAIS Go Stereo Pairing Guide............................................................................................................................8

Troubleshooting & Customer Support.......................................................................................................................9

Troubleshooting & Customer Support......................................................................................................................10

Safety and Precautions.........................................................................................................................................11

DC Power Supply

User Manual

Product Name: Bluetooth Speaker

Model:F5

Manufacture: Dongguan Jin wen hua digital technology Co., LTD.

User Manual

FCC Caution.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in

portable exposure condition without restriction.

Bluetooth Speaker

Summary of content (1 pages)

PAGE 1
User Manual 1.Volume down/Previous Track In the package........................................................................................................................................................1 Button and Connectors............................................................................................................................................2 Speciﬁcations..............................................................................................................................