LCD TELEVISION INSTRUCTION MANUAL C32HDHB C37HDHB C42HDHB C42FHDHB Proper use guarantees product life. Before using the product, be advised that you read this owner’s manual well and try to operate it.
Caution CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk electric shock.
Caution FCC RF INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio communications.
IMPORTANT SAFETY INSTRUCTIONS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
IMPORTANT SAFETY INSTRUCTIONS 16. Wall or Ceiling Mounting When mounting the product on a wall or ceiling, be sure to install the product using the designated mounting tool according to the method recommended by the manufacturer. 17. Attachments and Equipment Never add any attachment and/or equipment without approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury. 18.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user's own safety, and the proper operation of the product. In case of an accident, please unplug the unit from the outlet immediately. To reduce the risk of electric shock, do not remove cover or back. No user -serviceable parts inside. Refer to qualified service personnel for repair.
Warning This section must be read carefully and followed by the user prior to the operation of the product. The manual states important instructions for the user's own safety, and the proper operation of the product. Please keep the user's manual in a safe place for future reference. Do not put volatile substance-such as benzene, naphtha- near the product since it may cause a change in the product's color. Do not spill water or drop the remote control since it may be a cause of malfunctioning.
Table of Contents Installation and Maintenance Stand Construction Antenna Connection Video Connection Camcorder & Video Game Connection DVD Player Connection STB(Set Top Box) Connection PC Connection USB Connection Cable TV Broadcasting Connection Connect with the Dolby Digital AMP Name of Each Part Basic Guide Functionsa of the Remote Control Method To Use Basic Menu To Watch TV Setting Up TV Stations Selection of TV/VIDEO Input Signal Selection of Multimedia Input Signal Selection of Media(USB) Input Sign
Supplied Accessories Make sure that the following accessories are provided with the product. - AC cord AC cord Instruction manual Batteries Cable holder Remote control Cover Bottom -When installing wall mount, set the cover bottom as shown above Wall Mounting Unit (OPTIONAL) The method of wire arrangement 1. Assemble the cable holder enclosed on the back of TV.
Stand Construction 32” Stand Assy Construction 1. Insert the cover frame stand to the stand base 2. Insert the frame stand into the stand base ز ز ز ز 3. Assemble plate stand base and frame stand with the 4 screws supplied. ز ز ز When attaching stand to TV set, be sure to cover the surface to protect from accidental damage. 4. Assemble TV set and stand with the 3 screws supplied.
Stand Construction 37” Stand Assy Construction 1. Insert the TV set to the stand assy. ز When attaching stand to TV set, be sure to cover the surface to protect from accidental damage. ز ز 2. Assemble TV set and stand with screw 5EA.
Antenna Connection Indoor Antenna Connection 1. Connect the feeder cable of the antenna to the combining adapter. WHEN THE IMAGE IS NOT CLEAR : Unclear screen image and bad reception may be a cause of wrong antenna connection. Be sure to check its direction and place when installing. Combining adapter 2. Connect the combining adapter to the antenna input at the left side of the TV set. WHEN USING THE COMBINING ADAPTER : You may obtain the combining adapter at your closest Service Center.
Antenna Connection Antenna Connection When a coaxial cable is used : Plug the coaxial cable to the antenna socket on the wall. Antenna socket at the back of the TV set ANT When a feeder cable is used : Plug the coaxial cable to the antenna socket on the wall.
Antenna Connection Outdoor Antenna Connection Outdoor Antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses Single Antenna Connection VHF Antenna REAR OF THE TV SET L-AUDIO-R VIDEO L-AUDIO-R COMP 2 VIDEO Pb Pr L-AUDIO-R S-VIDEO Y OU T HDMI 2 MONITOR OPTICAL DIGITAL AUDIO COMP 1 INPUT PC/HDMI 1 HDMI 1 AUDIO PC SERVICE AV1 UHF Antenna ANT ANT Separate Antenna Connection.
Video Connection Connecting with an External Source You may connect S-Video1(Rear of the TV) input to enjoy clearer and brighter picture images. You can make the connection with the AV1 or AV2 input.
Camcorder & Video Game Connection Watching the Camcorder Recording or Video Game on TV 1. You can use either the S-video or the RCA connector. 2. These connectors connect to AV1/2 or S-Video1 as shown below. 3. Turn on the TV set and camcorder/video game. 4. Press "INPUT" and then You can see input menu. Select AV1, AV2 or S-Video1 mode by pressing " " and “OK” key.
DVD player connection When connecting with a component cable REAR OF THE TV SET Pb Pr L-AUDIO-R S-VIDEO Y VIDEO L-AUDIO-R AV1 L-AUDIO-R COMP 2 VIDEO OU T HDMI 2 MONITOR OPTICAL DIGITAL AUDIO COMP 1 INPUT PC/HDMI 1 HDMI 1 AUDIO PC SERVICE ANT Note : When you connect with the component, please check the color of cable between DVD and TV set.
STB(Set Top Box) Connection When connecting with a HDMI cable REAR OF THE TV SET HDMI 2 L-AUDIO-R VIDEO L-AUDIO-R Pb Pr L-AUDIO-R S-VIDEO Y AV1 COMP 2 VIDEO OU T MONITOR OPTICAL DIGITAL AUDIO COMP 1 INPUT PC/HDMI 1 HDMI 1 AUDIO PC SERVICE ANT When connecting with a component cable REAR OF THE TV SET Pb Pr L-AUDIO-R S-VIDEO Y VIDEO L-AUDIO-R Set Top Box 17 AV1 L-AUDIO-R COMP 2 VIDEO OU T HDMI 2 MONITOR OPTICAL DIGITAL AUDIO COMP 1 INPUT PC/HDMI 1 HDMI 1 AUDIO PC SERVICE
PC Connection When connecting with PC(D-Sub) cable. 1. Adjust PC resolution to available resolution in LCD TV. 2. Connect the PC and TV set using the D-Sub and Audio cable like below the picture. 3. Turn on the PC and TV set. 4. Press "INPUT" and then You can see input menu. Select PC mode by pressing " " or "OK" key.
PC Connection PC CONNECTION NOTES: 1) If there is a [Vertical Frequency] setting menu in the [Screen] Menu of the PC, adjust the frequency to 60Hz. 2) If the PC resolution is too high, it may be hard to read letters. Select a suitable resolution. 3) HDMI input port receives only Digital Signal. 4) Depending on the graphic card when you plug & unplug the HDMI connection, the screen may not display correctly. Restart the computer if this happens. Note : 1.
USB Connection • Connect the USB device to the USB in jacks on the side of TV. R-AUDIO-L VIDEO AV2 INPUT USB USB CONNECTION NOTES: Only a USB mass storage device is recognizable. If the USB storage device is connected through a USB hub, the device is not recognizable. A USB storage device using an automatic recognition program may not be recognized. A USB storage device which uses its own driver may not be recognized. The recognition speed of a USB storage device may depend on each device.
Cable TV Broadcasting Connection External Input Connection Source Watching cable television is only possible after you have subscribed to the local broadcasting company and installed a cable receiver. You may make the connection to either the Component input, Video1 input or Video2 input.
Connect with the Dolby Digital AMP. If you connect the optical output to a Dolby digital AMP, you can listen to better sound.
Name of Each Part Front Panel and Side Buttons on the TV set have the same functions as those of the remote control. INPUT 1 MENU 2 VOL 3 CH 4 POWER 5 SIDE OF THE TV SET Control Key Buttons. INPUT Buttons : Each time you press this button, the TV will cycle through: AIR/CABLE AV1 AV2 Component1 Component2 HDMI1 HDMI2 PC MENU Button : Use this button to enter and exit the MENU. VOL Buttons : Use this buttons to change your TV’s volume or to move cursor in the menu.
Name of Each Part Rear of the TV set Pb Pr L-AUDIO-R S-VIDEO Y VIDEO L-AUDIO-R REAR OF THE TV SET 24 AV1 L-AUDIO-R COMP 2 VIDEO OU T HDMI 2 MONITOR OPTICAL DIGITAL AUDIO COMP 1 INPUT PC/HDMI 1 HDMI 1 AUDIO PC SERVICE ANT
Functionsa of the remote control - 1, POWER : Turns the TV on and off. 2, NUMBER : Press the numbers on this board; you can select CH directly in TV mode. (EX: When you want to select CH10, you should press down "1", "0" and "OK" within 5second. If you only press down "1", after 5second, CH1 will be selected.) 3, DTV(-) : Used to enter a program number for multiple program channels such as 2-1, 2-2, etc. 4. PREVIOUS CH : Press this button, you can tune to the previous channel.
Battery Installation Inserting Batteries into the Remote Control Unit To install the batteries, turn the remote control over and open the battery compartment. Insert the batteries (Two 1.5V, type AAA). Make sure that the polarity matches with the (+) and (-) marks inside of the battery compartment. Note: To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time.
Basic Menu Basic Menu - The basic menu appears on the screen if you press the menu button of the remote control. - There are 5 items Picture, Sound, Channel, Features, and Time in the basic menu. - Each item has sub-items under it. If the desired item is selected, the relevant sub-items are displayed upward. 1. Press the "MENU" button. • The main menu appears if you press the “MENU” button. User 42 81 58 R G 50 Noise Reduction Off Color temp. Dimming 10 Aspect Ratio 16 : 9 PC Screen Mode Move 2.
To Watch TV Power, Number, DTV, OK, Mute, Input, , - Buttons with same name in the main body performs the same function. Press the “POWER” button on TV set or Remote control. Note: • The buttons of the remote control and the main body operate only when AC power turn on. • You must pull out the plug of TV set to shut off the AC Power - When pressing the Digit Key button • Press the "OK" button if using the number button for channel selection. For example, to watch the No.
To Watch TV 1. Press the “POWER” button on TV set or remote control. • The Stand-by LED lamp turns on in blue color. • Press the “POWER” button on the TV set or remote control. • The Stand By LED lamp on the front panel begins to flicker in blue color and the TV turns on. 2. Press the “ CH ” button. • Select the desired program by pressing the “ CH ” button or the number buttons. Analog Air 26 3. Adjust volume. • Sound reduces by pressing the “VOL ” button.
Setting Up TV Stations Auto Search to find Channels - All stations that can be received are stored by this method. It is recommended that you use Auto tuning during installation of this set. 1. Press the “MENU” button to select the Channel menu. • Move the selection bar to the Channel menu with ” ” buttons. Antenna Edit Channel Fine Tune Signal Strength Move 2. Select the “Antenna” • Place the selection bar on Antenna and select Air or Cable with “ ” buttons.
Setting Up TV Stations Fine tune 1. Searching for channel finely • Select a Channel number you want to tune finely with the “ CH ” buttons. • Press the “MENU” button and move to the Channel menu. • Move the selection bar to the Fine tune with ” ” buttons. • Press the “CB“ buttons to adjust the fine tuning.
