User's Manual

ManualsBrandsDongbu Daewoo Electronics ManualsElectronicsBluetooth Hands Free

Welcome

Welcome to GM’s “connected” world of Bluetooth

Personal area wireless networking. GM’s remote controlled CAR Kit with

Bluetooth Wireless Technology makes wireless connection simple and

quick.

GM’s remote controlled CAR Kit with Bluetooth Wireless Technology

offers these features:

z Seamless, wireless hands free audio through Bluetooth connection

z Digital audio interface with high quality, full-duplex, hands free speech

z Background noise reduction

z Acoustic echo cancellation

z Voice dialing through the phone

z Voice memo (duration 120 sec)

z Remote control keypad

z Speaker volume control with remote controller or audio volume knob

z Entertainment mute- automatically mutes radio during calls

z Compliance with Bluetooth Hands Free 1.1 profiles

z The “MDMTEC 1100” provides a wide array of functionality. Your specific

Bluetooth Phone may or may not fully support all of the “MDMTEC 1100”

functions.

Summary of content (13 pages)

PAGE 1
Welcome Welcome to GM’s “connected” world of Bluetooth ® Personal area wireless networking. GM’s remote controlled CAR Kit with Bluetooth Wireless Technology makes wireless connection simple and quick.
PAGE 2
Contents Welcome ………………………………………………………………………1 Safety and General Information…………………………………………..3 Installing the Bluetooth Hands free Kit . . . . . . . . . . . . . . . . . . . . . . . 4 Guidelines for Installation and Connection………………………………..4 How to install the Bluetooth hands free kit…………………………………4 Bluetooth Hands free kit contents…………………………………………..4 Installing the electronic Bluetooth module . . . . . . . . . . . …………………5 Installing the interface cable . . . . . . . . . . . . . . . . . . . …………………….
PAGE 3
Safety and General Information IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION. READ THIS INFORMATION BEFORE USING YOUR PHONE. Users are not permitted to make changes or modify the device in any way. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. See 47 CFR Sec. 15.21. This device complies with part 15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada.
PAGE 4
Declaration of Conformity Hereby, GM declares that this product MDMTEC 1100 is in compliance with: • The essential requirements and other relevant provisions of Directive 1999/5/EC • All other relevant EU Directives Installing the Bluetooth Handsfree Kit Guidelines for Installation and Connection • Only qualified personnel should install this car kit. If necessary, contact with vehicle manufacturer for air bag information specific to the vehicle. Caution: An air bag inflates with great force.
PAGE 5
Sensor with Microphone The microphone cable can be routed along the side of the vehicle, through the dash, and along the edge of the windshield. The microphone is placed best near the rearview mirror and aimed directly toward the user. Sensor with microphone is consisted of remote sensor,mic1,mic2 and indication led User Interface Remote Controller The User Interface Remote Controller(UIRC) can be mounted in several ways to provide a safe and comfortable environment for use. 1.
PAGE 6
Car radio with ISO( AMP 18 PIN, USCAR ) sockets : Disconnect the speaker harness. Connect the ISO( AMP 18 PIN, USCAR ) connector (car radio side) to the car radio, and connect the ISO( AMP 18 PIN, USCAR )connector (car speaker side), to the speaker harness. Installing the Sensor with Microphone 1. Select a suitable mounting location and mount the microphone: • It is recommended that the microphone be mounted on the headliner between the driver and passenger.
PAGE 7
Volume up/down Increase or decrease volume in a call or playback 0~9,*,# same function in phone Connecting Your Phone to the bluetooth hands free Car Kit Before you can use this car kit, you must complete a Bluetooth connection between the kit and your phone. You establish a Bluetooth connection between your car kit and phone with a paired link. When you set up a paired link, the car kit remembers the phone’s ID.
PAGE 8
Additional Pairing To pair additional phone to the system, with the car kit and phones in close proximity: Action 1 Press and hold the transfer button (phone diagram) in the Remote Control Keypad more 2 seconds until beep tone is generated. caution : Also you can disconnect your phone-> press and hold transfer button (phone diagram) button in the Remote Control Keypad more 2 seconds until beep tone is generated. 2 When prompted, display “TEL MUTE or VOICE IN” on the audio display for 4seconds.
PAGE 9
2. Select the device (MDMTEC 1100 o). The phone displays the passcode entry screen. 3 Enter the passkey (0000). The phone displays “PIN verified,” Note: Some phones ask you to accept the BT link. Enter Yes. Upon successful completion, connection is complete. Placing a Call with the Bluetooth Hands free Car Kit To place a call, you must first establish a Bluetooth link between the car kit and your phone .
PAGE 10
Using the Phone Press your phone’s END or hang up key(depending on your phone model) Using the UIRC (remote controller) Press the END button. LED wil be on(not blink) Using Features while on a Call Note: To use the functions described below: • A Bluetooth link must be established between the car kit and your phone. • A call must be initiating or in progress.
PAGE 11
If you want to erase the voice memo, press and hold “REC” until beep tone is generated. Turning Off System Prompts To turn off the system 1 Turn OFF the vehicle ignition 2 Also you can disconnect your phone-> press and hold “VC/PT”(PHONE diagram) button in the Remote Control Keypad more 2 seconds until beep tone is generated. 3 LED will be off. If You Need Help If you have any additional questions, please call your local hotline or dealer shop.
PAGE 12
Calling Features Quick Reference Dial Number Digit dial and press “HF” with UIRC(remote controller). Speed dial • Use the Speed Dial with UIRC(remote controller , only 2 digit). • Press 1st digit and press and hold 2nd digit (depend on the phone). Voice call • Press “VC/PT” (depend on the phone). Redial • Use last number redial from UIRC(remote controller). • Press the ‘HF” button. Some phone press the “HF” twice. Appendix Definitions Term Definition Boot The trunk. Handset The wireless phone.
PAGE 13
LED Indicator LED States states of connections Pairing off Pairing in progress Pairing on connected (in a Call) Not Connected OFF OFF ON N/A incoming call or connected(in a Call) OFF N/A blinking N/A RECORDING N/A N/A N/A blinking PLAYBACK N/A N/A blinking blinking z Turn OFF the vehicle ignition, LED is off.